Hyperdrill AF 204 RD
Page 1 of 4
MATERIAL SAFETY DATA SHEET
SECTION I: IDENTIFICATION OF PRODUCT
PRODUCT NAME: Hyperdrill AF 204 RD
PRODUCT USE: Oil Well Fluid Additive
CHEMICAL FAMILY: Anionic acrylamide copolymer powder
WORK PLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS)
WHMIS CLASSIFICATION: Not a Controlled Product Under WHMIS
WORK PLACE HAZARD: N/A
TRANSPORTATION OF DANGEROUS GOODS (TDG)
SHIPPING NAME: Not Regulated Under TDG
TDG CLASSIFICATION: N/A
UN NUMBER (PIN): N/A
PACKING GROUP: N/A
SECTION II: HAZARDOUS INGREDIENTS
INGREDIENT PERCENT CAS NUMBER LD(50) Oral-Rat OSHA PEL ACGIH TLV
No Hazardous Ingredients
SECTION III: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY: [XX] SKIN [XX] EYE CONTACT [XX] INHALATION [XX] INGESTION
EFFECTS OF Skin irritation of dermatitis may occur upon frequent of prolonged contact. Repeated of
CHRONIC EXPOSURE: prolonged contact may cause sensitisation in some individuals.
EYE CONTACT: No effects of exposure expected with the exception of possible irritation.
SKIN CONTACT: No effects of exposure expected due to contact. Prolonged contact may cause skin
irritation or dermatitis in some individuals.
INGESTION: No adverse effects expected. LD (oral rat): >2,000 mg/kg.
50
INHALATION: May cause sneezing, slight irritation of nose and throat.
SECTION IV: FIRST AID MEASURES
Hyperdrill AF 204 RD
Page 2 of 4
MATERIAL SAFETY DATA SHEET
SKIN CONTACT: Wash exposed area with soap and water. If irritation or abnormalities persist, call a
physician.
EYE CONTACT: Immediately flush eyes with water for 15 minutes and call a physician.
INGESTION: Do not induce vomiting. Dilute by giving two glasses of water. Never give anything by mouth
to an unconscious person. Call a physician.
INHALATION: Remove to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. If
breathing is difficult, give oxygen. Call a physician.
SECTION V: PHYSICAL DATA
APPEARANCE AND ODOUR: White granular solid; faint odour
SPECIFIC GRAVITY: 0.80 g/cc
Decomposes
BOILING POINT (掳C):
N/A
MELTING POINT (掳C):
pH: 6.5-8.5
SOLUBILITY IN WATER: Soluble
PERCENT VOLATILE BY VOLUME: N/A
EVAPORATION RATE: N/A
VAPOUR PRESSURE (mm Hg): Very Low
VAPOUR DENSITY (Air = 1): N/A
SECTION VI: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: N/A
FLAMMABLE LIMITS: N/A
EXTINGUISHING MEDIA: Dry chemical, foam, CO
2
SPECIAL FIRE FIGHTING PROCEDURES: Self-contained respirators required for fire fighting personnel. Water
may cause excessive slipperiness.
HAZARDOUS COMBUSTION PRODUCTS: Oxides of carbon, nitrogen and products of incomplete combustion.
UNUSUAL FIRE/EXPLOSION HAZARDS: Requires a source of ignition, the presence of air, and a
temperature greater than the flash point.
Hyperdrill AF 204 RD
Page 3 of 4
MATERIAL SAFETY DATA SHEET
SECTION VII: REACTIVITY DATA
STABILITY: Stable [XX] Unstable [ ]
INCOMPATIBILITY (CONDITIONS TO AVOID): Avoid contamination with reactive substances such as strong
oxidizing agents and caustic solutions.
HAZARDOUS DECOMPOSITION PRODUCTS: N/A
HAZARDOUS POLYMERIZATION: Will Not Occur [XX] May Occur [ ]
SECTION VIII: PREVENTIVE MEASURES
SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Suggest NIOSH/MESA approved dust mask.
VENTILATION: 10 changes per hour suggested.
PROTECTIVE GLOVES: Suggest plastic or rubber.
EYE PROTECTION: Suggest goggles.
OTHER PROTECTIVE EQUIPMENT (Specify): Clothing as required to prevent contact.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Avoid prolonged or frequent contact when handling material. Do not inhale dust. Keep container closed when not in
use. Store in cool and dry location away from oxidizing and reducing agents.
Wear a NIOSH-approved mechanical-filter respirator, if adequate ventilation cannot be provided. Avoid skin or eye
contact. Protective measures during repair/maintenance of equipment: Wash equipment thoroughly with steam or
warm water until clean. In all cases, follow good industrial safety practices before entering equipment.
STEPS TO BE TAKEN IN CASE THE MATERIAL IS SPILLED OR RELEASED
Ventilate area. Wear rubber boots, gloves, and a self-contained breathing apparatus if ventilation is not adequate.
Collect into waste container. Avoid raising dust. Wash spill site after material pick-up. Water solutions are very
slippery. May constitute a hazard following a spill.
WASTE DISPOSAL METHOD
Dispose of waste according to federal, provincial, and local regulations.
SECTION IX: PREPARATION
THE INFORMATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESSED OR
IMPLIED, IS MADE.
Hyperdrill AF 204 RD
Page 4 of 4
MATERIAL SAFETY DATA SHEET
DATE PRINTED: April 6, 2006 BY: MILLENNIUM TECHNOLOGIES LTD.
DATE MODIFIED: May 18, 2004 APPROVED BY:
SUPERSEDES: October 1, 2003
|