139377 Page 1 of 4
MATERIAL SAFETY DATA SHEET
Ford Internal Reference Number(Tox No. : 139377)
Print Date : 09/19/03
Language: English
Part Type and Number Part name
--------------------------------------- --------------------------------------
Motorcraft - U.S. XG-4 MOTORCRAFT MULTI-PURPOSE GREASE (4
OZ TUBE)
Approved to Active Production-North American spec ESB-M1C93-B
====================== CHEMICAL AND PHYSICAL PROPERTIES =======================
Appearance : Physical State GREASE
Form GREASE
Color TAN
Specific Gravity (Relative Density) 0.904
Boiling Point >+288 掳C
Flash Point +227 掳C (+440 F) (CLEVELAND OPEN CUP)
pH full strength -
pH diluted -
Odor BLAND
Odor Threshold -
Viscosity 1,000 at +37.8C
Vapor Density >5 (AIR=1)
Vapor Pressure 0.01
Evaporation Rate <0.01 (N-BUTYL ACETATE=1)
Freezing Point -22 掳C
Explosion Properties : UEL 7.0
LEL 0.9
Auto-ignition Temperature -
Solubility NEGLIGIBLE
Partition Coefficient -
================== HAZARDOUS AND OTHER DISCLOSED INGREDIENTS ==================
Percent Exposure Limits - TWA
Range ACGIH/OSHA(where est.) CAS number Chemical Name
------------ ---------------------- ------------ --------------------------
45-50 5/5 64742-62-7 RESIDUAL OILS
Ford= 1.0 mg/m3 (PETROLEUM), SOLVENT
DEWAXED
35-40 5/5 64742-52-5 PETROLEUM DISTILLATES,
Ford= 1.0 mg/m3 HYDROTREATED HEAVY
NAPHTHENIC
0-3 Not Regulated 68649-42-3 PHOSPHORODITHIOIC ACID,
O,O-DI-C1-14-ALKYL
ESTERS, ZINC SALTS
http://www.mats.ford.com/mats/cgi-bin/aft_msds_generation.cgi?language=US&tox=139377 9/19/2003
...
139377 Page 2 of 4
Exposure Limit Abbreviations
--------------------------------------
TWA=Time Weighted Average C=Ceiling
S=Short Term Exposure Sk=Skin
Sol=Soluble Compounds Fu=Fumes
Insol=Insoluble Compounds Du=Dust I=IARC Resp=Respirable
=========================== REGULATORY INFORMATION ============================
This product contains an ingredient present on the WHMIS (0.1%) Ingredient
Disclosure List.
This product contains a toxic chemical or chemicals subject to the reporting
requirements of Section 313 of Title III of the Superfund Amendments and
Reauthorization Act of 1986 and 40 CFR Part 372.
The supplier of this product did not provide information concerning the
classification of this product under the Canadian Controlled Products Act.
================================= SIGNAL WORD =================================
CAUTION
========================== HEALTH HAZARD INFORMATION ==========================
=(A)=============================== HAZARDS ===================================
Exposure to oil mist/fume/vapor may cause respiratory tract irritation.
Prolonged and/or repeated skin contact with this product may cause
irritation/dermatitis.
This product may cause irritation to the eyes.
=(B)================ TARGET ORGANS AND MEDICAL CONDITIONS =====================
Overexposure to some hazardous ingredients in this product has been found
to affect certain body organs and systems in experimental animals and/or
humans. These include:
Skin, Eyes, and Respiratory System
Medical conditions which may be aggravated by exposure to this product are
pre-existing disorders of the:
Skin, Eyes, and Respiratory System
=(C)===================== ACUTE TOXICITY INFORMATION ==========================
Based on the composition of the product identified by the supplier,
selected portions of the acute toxicity information from RTECS are
as follows:
9002-88-4 POLYETHYLENE
Inhalation, mouse, LC50 = 12 gm/m3 (30 Minutes)
======================= FIRE AND EXPLOSION INFORMATION ========================
EXTINGUISHER INFORMATION: Dry chemical, foam, carbon dioxide, water fog.
Wear self-contained breathing apparatus.
Water or foam may cause frothing if the product is heated above
http://www.mats.ford.com/mats/cgi-bin/aft_msds_generation.cgi?language=US&tox=139377 9/19/2003
...
139377 Page 3 of 4
93 degrees C (200 degrees F).
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or
low molecular weight hydrocarbons.
Water may be used to cool exposed containers to prevent pressure build-up
and explosion when exposed to extreme heat.
=============================== REACTIVITY DATA ===============================
This is a stable material.
Hazardous polymerization will not occur.
This product may react with strong oxidizing agents (bleach--sodium
hypochlorite, calcium hypochlorite, hydrogen peroxide, permanganate,
nitric acid, concentrated OXYGEN, perchlorates).
============================= PREVENTIVE MEASURES =============================
=(A)====================== SAFE HANDLING AND STORAGE ==========================
Avoid getting this material into contact with your eyes.
Avoid prolonged or repeated skin contact with this material.
Use this product with adequate ventilation.
Avoid the generation of oil mists.
Petroleum distillate base oils used in the product are severely hydrotreated
and/or solvent refined.
=(B)========================= PROTECTIVE MEASURES =============================
Wear safety glasses.
Use general ventilation and use local exhaust, where possible, in confined or
enclosed spaces.
The use of nitrile-latex gloves is recommended.
Barrier creams that are specific for oil based materials are recommended when
gloves are impractical to use.
Use NIOSH approved respirator in compliance with OSHA Respiratory Standard
29CFR 1910.134 or Canadian Z94.4 for the particular hazard or airborne
concentration to be encountered in the work environment. U.S. plants should
consult OSHA 29CFR 1910.134 for selection of proper respirator(s). Canadian
plants should consult CSA Standard Z94.4-96
=(C)===================== SPILLS, LEAKS AND DISPOSAL ==========================
Wear appropriate protective equipment and clothing during clean-up.
Attempt to reclaim the free product, if this is possible.
Waste disposal - This material should be disposed of separately or with plant
used motor oils, indicating the material's potential to cause skin
cancer with prolonged and repeated contact.
Transport waste material to an authorized waste location, or incinerate under
controlled conditions.
Absorb the spilled material with an inert absorbent (nonflammable) material.
Vacuum up the spilled material.
Avoid excessive skin contact with the spilled material.
Do not allow the spilled product to enter public drainage system or open water
courses.
Surfaces may become slippery after spillage.
Dispose of waste material according to Local, State, Federal, and
Provincial Environmental Regulation.
============================= FIRST AID TREATMENT =============================
In case of contact with eyes, rinse immediately with plenty of water and seek
http://www.mats.ford.com/mats/cgi-bin/aft_msds_generation.cgi?language=US&tox=139377 9/19/2003
...
139377 Page 4 of 4
medical advice.
Remove contaminated clothing and wash before reuse.
If the material is swallowed, get immediate medical attention or advice --
Do not induce vomiting.
Wash thoroughly after handling.
If inhalation of gas/fume/vapor/dust/mist from the material is excessive (air
concentration is greater than the TLV or health effects are noticed),
immediatly remove the affected person(s) to fresh air.
===================== ENVIRONMENTAL INFORMATION: ECOLOGY ======================
Material contains a chemical which is a Ford Motor Company Material of
Concern. Use and release of this material should be minimized to the
greatest extent possible.
============================ Transport Information ============================
U.S. Department of Transportation (DOT) 49 - CFR 172.101
This product is not regulated as a dangerous good.
Canadian Transportation of Dangerous Goods (T.D.G.) -TDGR
This product has not been reviewed for this regulation.
Secretary of Communication and Transportation (SCT)- NOM-002-SCT2/1994 (Mexico)
This product has not been reviewed for this regulation.
International and Domestic Air Transportation - ICAO & IATA Section 4.2
This product has not been reviewed for this regulation.
International Water Transportation - IMDG Code Amendment 31-02
This product has not been reviewed for this regulation.
=========================== PREPARATION INFORMATION ===========================
Health and safety information has been evaluated by:
Occupational & Environmental Health Sciences Department
Ford Motor Company
Central Laboratory Building - Rm S-120
15000 Century Drive
Dearborn, Michigan 48120
For 24 hour emergency information dial 1-800-959-3673.
This is the last page of this MSDS.
Date of Preparation: 02/07/02
http://www.mats.ford.com/mats/cgi-bin/aft_msds_generation.cgi?language=US&tox=139377 9/19/2003
...
|