Aexcel Corporation
Material Safety Data Sheet
I. PRODUCT AND COMPANY IDENTIFICATION
Product Name: 72W-A057
72W-A057
Product Code:
White Jet-Dry Waterborne Traffic Marking Paint
Description:
Aexcel Corporation
Manufacturer:
7373 Production Drive
Mentor, OH 44060
Information: 440-974-3800
Phone Numbers:
Emergency/CHEMTREC: 800-424-9300
2 2005-05-09 15:11:48
MSDS Rev No./Date:
II. COMPOSITION/INFORMATION ON POTENTIALLY HAZARDOUS INGREDIENTS
Chemical Name CAS No. Wt % OSHA Permissible Exposure Limits (PEL)
STEL TWA
TEXANOL 25265-77-4 1.84 N.E. N.E.
METHYL ALCOHOL 67-56-1 1.47 250 PPM (SKIN) 200 PPM (SKIN)
III. HAZARDS IDENTIFICATION
HMIS Safety Ratings Health Flammability Reactivity
1 0 0
(0 - 4, 4 = severe hazard)
Health Hazards
Skin contact, Inhalation, Absorption, Eye contact
Routes of Entry:
Kidneys, Liver, Lungs, Pancreas, Heart, Brain
Target Organs:
Immediate (Acute) Health Effects by Route of Exposure:
Repeated exposure by inhalation may cause systemic poisoning, brain disorders,
Inhalation Irritation:
impaired vision and blindness.
Can cause minor skin irritation, defatting, and dermatitis.Continued or prolonged
Skin Contact:
contact may irritate the skin and cause a skin rash (dermatitis).
May cause mild skin irritation.
Skin Absorption:
Can cause minor irritation, tearing and reddening.Can causes slight irritation.
Eye Contact:
May be fatal or cause blindness if swallowed.Harmful if swallowed.
Ingestion Irritation:
Long-Term (Chronic) Health Effects:
None of the substances have been shown to cause cancer in long term animal
Carcinogenicity:
studies. Not a carcinogen according to NTP, IARC, or OSHA.Material did not
cause cancer in long-term animal studies.
Reproductive/Developmental: No data available to indicate product or any components present at greater than
0.1% may cause birth defects.A component in this product has been shown to
cause birth defects and reproductive disorders in laboratory animals at high
doses.
No data available to indicate product or any components present at greater than
Mutagenicity:
0.1% is mutagenic or genotoxic.
Repeated exposure by inhalation may cause system poisoning, brain disorders,
Inhalation:
impaired vision and blindness.
Upon prolonged or repeated contact, can cause minor skin irritation, defatting,
Skin Contact:
72W-A057
Page 1 of 4
and dermatitis.
Upon prolonged or repeated exposure, harmful if absorbed through the skin. May
Skin Absorption:
cause minor systemic damage.
May be fatal or cause blindness if swallowed.
Ingestion:
IV. FIRST-AID MEASURES
If breathing stops or shows signs of failing, give artificial respiration Remove to
Inhalation:
fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Get immediate medical attention.
Use an eye wash to remove a chemical from your eye regardless of the level of
Eyes:
hazard. Flush the affected eye for at least twenty minutes. Tilt the head to prevent
chemical from transferring to the uncontaminated eye. Seek medical advice after
flushing.
Wash with soap and water. Immediately flush skin with plenty of water. Remove
Skin Contact:
clothing. Get medical attention immediately. Wash clothing separately from other
articles before reuse.
If swallowed, have a trained medical professional induce vomiting immediately.
Ingestion:
Never give anything by mouth to an unconscious person.
V. FIRE FIGHTING MEASURES
Non-Flammable
Flammability Summary:
Foam, carbon dioxide (CO2) dry chemical or water fog spray. Steams of water
Extinguishing Media:
are not ordinarily effective. Solid hose streams tend to scatter liquid and spread
the fire. Water foams, water foam nozzles cool the burning surface and exclude
air.
Keep containers tightly closed, isolate from heat, sparks and open flame. Closed
Fire Fighting Instructions:
containers may explode when exposed to extreme heat. In a test "Evaluation of
the Fire Hazard of Water Borne Coatings" (Factory Mutual Research
Corporation Scientific Circular 804 December 1977) for water-borne coatings,
"Represented not fire hazard". It was also concluded that results from laboratory
(flash point) tests are not a representative indication of the fire hazard of water-
borne coatings".
Flash Point: > 200 Deg. F. TCC
Flashpoint TCC deg F Autoignition Temp UEL % in air LEL % in air
Component Parameters:
deg F
TEXANOL 248 740.00 0.6 4.2
METHYL ALCOHOL 54 725.00 36.0 6.0
VI. ACCIDENTAL RELEASE MEASURES
Small Spill/Large Spill: Collect in retaining area or container. Then transfer to a closed container. Avoid
exposure to heat, sparks, fire or open flame. Avoid hot metal surfaces.
VII. HANDLING AND STORAGE
Handling/Storage: Containers of this material may be hazardous when emptied. Since emptied containers retain
product residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed. All
five-gallon pails and larger metal containers, including tank cars and tank trucks, should be grounded and/or bonded
when material is transferred. Emergency eyewash fountains and safety showers should be available in the
immediate vicinity of potential exposure.
72W-A057
Page 2 of 4
KEEP FROM FREEZING
VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION
Provide sufficient general end/or local exhaust ventilation to maintain
Engineering Measures:
exposure below TLV(s).
If workplace exposure limit(s) of product or any component is exceeded,
Respiratory Protection:
a NIOSH/MSHA approved air supplied respirator is advised in absence
of proper environmental control. OSHA regulations also permit other
NIOSH/MSHA respirators under specified conditions. Engineering or
administrative controls should be implemented to reduce exposure.
Wear safety glasses when handling this product.
Eye Protection:
Avoid skin contact by wearing chemically resistant gloves, an apron and other
Skin Protection:
protective equipment depending upon conditions of use. Inspect gloves for
chemical break-through and replace at regular intervals. Clean protective
equipment regularly. Wash hands and other exposed areas with mild soap and
water before eating, drinking, and when leaving work. Use impervious gloves.}
Chemically resistant gloves
Gloves:
Control Parameters:
ACGIH TLV-TWA ppm ACGIH STEL ppm IDLH ppm
Chemical Name
TEXANOL NE NE
METHYL ALCOHOL 200 250 0
IX. PHYSICAL AND CHEMICAL PROPERTIES
Heavy White Liquid
Appearance:
13.62 s/gal
Bulk Density:
24.2%
Volatiles, by weight:
40.3%
Volatiles, by volume:
VP mmHg @ deg F Vapor Density Evaporation Rate BP F
Component Properties:
(1 = air) (1 = n-butyl acetate) at 1 atm
TEXANOL 1.000 189 7.450 0.00 471
METHYL ALCOHOL 47.300 77 1.110 5.90 149
X. STABILITY AND REACTIVITY
Stable under normal conditions.
Stability/Reactivity:
Sparks, open flame, other ignition sources, and elevated temperatures.Avoid all
Conditions to Avoid:
sources of ignition.
Acetaldehydes Strong acids Oxidizing materials
Chemical Incompatibility:
XI. TOXICOLOGICAL INFORMATION
No data
XII. ECOLOGICAL INFORMATION
No data
XIII. DISPOSAL CONSIDERATIONS
Dispose of in accordance with all applicable local, state and federal regulations.
Disposal Methods:
XIV. TRANSPORTATION INFORMATION
72W-A057
Page 3 of 4
Paint, Latex
DOT Basic Description:
Non-Hazardous
Hazard Class:
Non-Regulated
UN Number:
XV. REGULATORY INFORMATION
A component or components of this product are listed on the TSCA Inventory of Existing Chemical
TSCA Status:
Substances.
Chemical Name CAS # Regulation
Methanol 67-56-1 CERCLA
Methanol 67-56-1 SARA 312
Methanol 67-56-1 SARA 313
Ammonia 7664-41-7 SARA EHS
Methanol 67-56-1 CAA HAP
Methanol 67-56-1 PA Regulated Mat'l
Methanol 67-56-1 MA Right-to Know
Methanol 67-56-1 NJ Regulated Mat'l
XVI. ADDITIONAL INFORMATION
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS TO THE BEST
Disclaimer:
OF OUR KNOWLEDGE TRUE AND ACCURATE, BUT IS OFFERED WITHOUT WARRANTY,
EXPRESS OR IMPLIED. CONDITIONS OF USE ARE BEYOND OUR CONTROL. NEITHER
AEXCEL CORPORATION NOR ITS AGENTS SHALL BE LIABLE FOR ANY DIRECT OR
CONSEQUENTIAL INJURY, LOSS, OR DAMAGE ARISING FROM THE USE OR INABILITY
TO USE THE PRODUCT DESCRIBED HEREIN. NO PERSON IS AUTHORIZED TO MAKE ANY
STATEMENT OR RECOMMENDATION NOT CONTAINED IN THIS MSDS. ANY SUCH
STATEMENT OR RECOMMENDATION IF MADE SHALL NOT BIND THE CORPORATION.
72W-A057
Page 4 of 4
|