MATERIAL SAFETY DATA SHEET
ACCUMETRIC INC.
BOSS庐 PRODUCTS
350 RING ROAD
ELIZABETHTOWN, KY 42701
800-928-2677
BOSS庐 286
______________________________________________________________________________
SECTION 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Tradename: BOSS庐 286
General Use: When fully cured, the mixed product is non-hazardous
Chemical Family: Epoxy Resin & Polycaptan Curing Agent
Accumetric Inc.
350 Ring Road
Elizabethtown, KY 42701
Emergency Information: Chemtrec: 800-424-9300
Other Calls; Accumetric Inc.: 502-769-3385
______________________________________________________________________________
SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous Constituents
Constituent Abbr. CAS No. Wt. % ACGIH OSHA Other
Bisphenol A diglycidyl ether resin
DGEBPA 25068386 10-45 n/e n/e n/e
2,4,6-Tri-(dimethylaminomethyl)phenol
DMP 90722 1-15 n/e n/e n/e
Mercaptan amine blend 10-40 n/e n/e n/e
"TLV" means the Threshold Limit Value exposure (eight-hour, time-weighted average, unless otherwise noted)
established by the American Conference of Governmental Industrial Hygienists. "STEL" indicates a short-term
exposure limit. "PEL" indicates the OSHA Permissible Exposure Limit. "n/e" indicates that no exposure limit has
been established. An asterisk (*) indicates a substance whose identity is a trade secret of our supplier and unknown
to us.
- MATERIAL SAFETY DATA SHEET - PAGE 2
______________________________________________________________________________
SECTION 3. HAZARDS IDENTIFICATION
Emergency Overview
Appearance, form, odor: (Color varies) putty with low odor.
Caution! Eye and skin irritant. Potential skin sensitizer. Avoid eye contact. May be
harmful if swallowed. Wash with soap and water after use. In case of eye contact, flush
with water for 15 minutes and seek medical attention.
Potential Health Effects
Primary Routes of Exposure: Skin Contact X
Skin Absorption
Eye Contact X
Inhalation
Ingestion
Symptoms of acute overexposure:
Skin: May cause irritation and sensitization to sensitive skin
Eyes: Mild irritation
Inhalation: No data
Ingestion: No data. May cause irritation
Effects of chronic overexposure:
Prolonged or repeated overexposure may cause allergic sensitization.
Carcinogenicity - OSHA regulated: No ACGIH: No
National Toxicology Program: No
International Agency for Research on Cancer: No
Cancer-suspect constituent(s): None
Medical Conditions which may be aggravated by exposure:
Dermatitis and skin allergies.
Other effects:
See SECTION 11.
- MATERIAL SAFETY DATA SHEET - PAGE 3
______________________________________________________________________________
SECTION 4. FIRST AID MEASURES
First aid for eyes: Flush with clear water for 15 minutes.
First aid for skin: Wash thoroughly with soap and water.
First aid for inhalation: Remove to fresh air.
First aid for ingestion: Contact a physician. Do not induce vomiting.
______________________________________________________________________________
SECTION 5. FIRE FIGHTING PROCEDURES
Extinguishing Media: Water
Carbon dioxide X
Dry chemical X
Foam X
Alcohol Foam
Flash Point (oF): >300
Method: TOC
Explosive limits in air (percent) - Lower: n/d Upper: n/d
Special firefighting procedures:
Firefighters should wear self-contained breathing apparatus and protective clothing.
Unusual fire and explosion hazards:
None.
Hazardous products of combustion:
Oxides of carbon and nitrogen. Ammonia.
Other unknown, potentially toxic contaminants.
______________________________________________________________________________
SECTION 6. ACCIDENTAL RELEASE MEASURES
Spill Control:
Avoid personal contact. Eliminate ignition sources. Ventilate area.
Contaminant:
Dike, contain and absorb with clay, sand or other suitable material.
Cleanup:
Pick up and dispose of in an appropriate container.
Flush area with water to remove trace residue.
Special Procedures:
Prevent spill from entering
- MATERIAL SAFETY DATA SHEET - PAGE 4
______________________________________________________________________________
SECTION 7. HANDLING AND STORAGE
Handling Precautions:
Avoid contact with skin, eyes, or clothing. Wash thoroughly with soap and water after using and
particularly before eating, drinking, smoking, applying cosmetics or using toilet facilities.
Launder contaminated clothing and protective gear before reuse. Discard contaminated leather
articles.
Handle mixed resin and hardener in accordance with the potential hazard of the curing agent
used. Provide appropriate ventilation/respiratory protection against decomposition products (see
SECTION 10) during welding/flame cutting operations and particles (silica) during
sanding/grinding operations.
Storage:
Store in a cool, dry area away from high temperatures and flames.
______________________________________________________________________________
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering controls
Ventilation:
General mechanical is satisfactory. If odor is disagreeable, use local exhaust.
Other engineering controls:
Have emergency shower and eye wash available
Personal protective equipment
Eye and face protection:
Safety glasses
Skin protection:
Polyethylene gloves for prolonged use.
Respiratory protection:
Non needed in normal use with proper ventilation.
______________________________________________________________________________
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Boiling point (oF):
Specific gravity: 1.9 n/d
Melting point: n/d Vapor density (air=1): >1
- MATERIAL SAFETY DATA SHEET - PAGE 5
Vapor pressure Evaporation rate
Nil at 78 oF
(mmHg): (butyl acetate =1): <1
VOC (grams/liter): 0 Solubility in water: negligible
Percent volatile
by volume: 0 pH (5% solution or slurry in water): n/d
Percent solids by weight: 100
______________________________________________________________________________
SECTION 10. STABILITY AND REACTIVITY
This material is chemically stable. Hazardous polymerization will not occur.
Conditions to avoid:
Exposure to open flame or excessive heat.
Incompatible materials:
Strong oxidizing agents
Hazardous products of decomposition:
Oxides of carbon, sulfur and nitrogen. Aldehydes and acids. Other, unknown and potentially
toxic contaminants.
Conditions under which hazardous polymerization may occur.
None.
______________________________________________________________________________
SECTION 11.TOXICOLOGICAL INFORMATION
Acute oral effects: LD50 (rat): Not determined
Acute dermal effects: LD50 (rabbit): Not determined
Acute inhalation effects: LC50 (rat): Not determined Exposure: hours
Eye irritation: Slight irritant (rabbit)
Subchronic effects: No data available
Carcinogenicity, teratogenicity, and mutagenicity:
Both the resin and the diglycidyl ether of bisphenol A (a component of this product) have proved
to be inactive when listed by in vivo mutagenicity assays. Both have shown activity by In Vitro
microbial mutagenicity screening and have produced chromosomal aberrations in cultured rat
liver cells.
- MATERIAL SAFETY DATA SHEET - PAGE 6
Other chronic effects:
2-year bioassays in mice exposed by the dermal route to EPON 828, DGEBPA, or other
commercial resins yielded limited evidence of weak carcinogenicity. The authors concluded that
the renal tumor evidence with EPON 828 "was of no biological significance" and that the resin
"is not a systemic carcinogen when applied to the dorsal skin of CF1 mice." Overexposure to
fumes and vapors of amine components may cause lung injury or chemical pneumonia.
Toxicological information on hazardous chemical constituents of this product:
Constituent Oral LD50 Dermal LD50 Inhalation LC50
(rat) (rabbit) 4 hr, (rat)
Bisphenol A diglycidyl ether resin
30 g/kg >20 ml/kg no deaths
2,4,6-Tri(dimethylaminomethyl)phenol
1200 mg/kg 1350 mg/kg >0.5 mg/L
Mercaptan amine blend
n/d n/d n/d
"n/d" = not determined
______________________________________________________________________________
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity: No data
Mobility and persistence: No data
Environmental fate: No data
______________________________________________________________________________
SECTION 13. DISPOSAL CONSIDERATIONS
Please see also SECTION 15, Regulatory Information
Waste Management recommendations:
If this resin becomes a waste, it would not be a hazardous waste by RCRA criteria (40CFR 261).
Dispose of according to applicable federal, state, and local regulations.
- MATERIAL SAFETY DATA SHEET - PAGE 7
______________________________________________________________________________
SECTION 14. TRANSPORT INFORMATION
Proper shipping name: Non-regulated material
Technical name:
Hazard class:
UN number:
Packing group:
Emergency Response Guide No.:
IMDG page number:
Other:
______________________________________________________________________________
SECTION 15. REGULATORY INFORMATION
U.S. Federal Regulations
TSCA
All ingredients of this product are listed, or are exempt from listing, on the TSCA inventory.
The following RCRA code(s) applies to this material if it becomes waste: None
Regulatory status of hazardous chemical constituents of this product:
Constituent Extremely Toxic CERCLA TSCA 12B Export
Hazardous* Chemical** RQ (lbs) Notification
Bisphenol A diglycidyl ether resin
No No None Required
2,4,6 Tri(dimethylaminomethyl)phenol
No No None Not Required
Mercaptan amine blend
No No None Not Required
*Consult the appropriate regulations for emergency planning and release reporting requirements for substances on
the SARA Section 301 Extremely Hazardous Substance list.
**Substances for which the "Toxic Chemical" column is marked "Yes" are on the SARA Section 313 list of Toxic
Chemicals, for which release reporting may be required. For specific requirements, consult the appropriate
regulations.
- MATERIAL SAFETY DATA SHEET - PAGE 8
For purposes of SARA Section 312 hazardous materials inventory reporting, the following
hazard classes apply to this material.
Immediate Health Hazard - Delayed Health Hazard
Canadian Regulations
WHMIS hazard class(es): None
All components of this product are on the Domestic Substances List.
______________________________________________________________________________
SECTION 16. OTHER INFORMATION
Hazardous Materials Information
System (HMIS) ratings: Health 1, Flammability 1, Reactivity 0
The information and recommendations in this document are based on the best information available to us at the time
of preparation, but we make no other warranty, express or implied, as to its correctness or completeness, or as to the
results of reliance on this document.
|