PRODUCT DATA SHEET
CLEAR GENERAL PURPOSE ADHESIVE
PART NO. 4005Z
DESCRIPTION
Dynatex庐 General Purpose Adhesive is a single component, medium to high viscosity
Cyanoacrylate adhesive. Designed for general purpose bonding on all types of
substrates where gap filling is required.
PHYSICAL PROPERTIES
MONOMER (Liquid)
Base Compound ........................................................... Ethyl Cyanoacrylate
Appearance........................................................................ Colorless Liquid
Viscosity (cps @ 680F) ..................................................................... 800 cP
Specific Gravity (g/cc)......................................................................... 1.06
Flash Point (TCC) ............................................................................. 1850F
Shelf Life @ 400F...................................... One year in unopened containers
Military Specifications...................................... Mil-A-46050C Type ll, Class 3
CURING PROPERTIES
Ambient surface moisture will initiate the hardening process. Handling strength is
reached in a short period of time and varies depending on environmental conditions
and substrates being bonded. Product will continue to cure for at least 24 hours before
full strength and resistances are developed.
Setting Time (68 F, 65% R.H.)
Steel ...............................................................................10 to 20 seconds
Aluminum ........................................................................ 10 to 17 seconds
Neoprene............................................................................... <10 seconds
ABS...................................................................................5 to 10 seconds
Polycarbonate ..................................................................10 to 20 seconds
PVC...................................................................................8 to 15 seconds
CURING PERFORMANCE
The gap of the bond line will affect set speed. Smaller gaps tend to increase the speed.
Activators can be applied to improve set speed but may also impair overall adhesive
performance.
Pg. 2 of 3
P/N 4005Z
POLYMER (Cured)
Appearance..........................................................................Colorless Solid
Service Temperature Range ..................................................-650F to 2000F
Softening Point................................................................................. 3290F
Refractive Index (ND 20) .................................................................... 1.49
C. CURE SPEED (Seconds)
Full Cure Time............................................................................. 24 Hours
Dielectric Strength KV/mm .................................................................. 11.6
Dielectric Constant @ 1Kc ..................................................................... 5.4
Coefficient of Thermal Expansion (in./in./F) ..................................... .000126
Tensile Strength (Steel/Steel) ........................................................ 3200 psi
Solubility................................... Nitromethane, Acetone, Dimethylformamide
Performance of Cured Materials
(Tensile shear strength after 48 hours @ 20-250C (68-770F)
Substrate Range in N/mm2
Blasted Steel .................................................................................17 to 23
Etched Aluminum ..........................................................................12 to 22
Neoprene............................................................................................>10
ABS..................................................................................................... >6
Polycarbonate ...................................................................................... >5
PVC..................................................................................................... >6
CHEMICAL RESISTANCE
Sheer strength on steel after 12 month soak
Solvent % Strength Retained
Motor Oil .............................................................................................. 90
Gasoline ............................................................................................. 100
Trichloroethane ................................................................................... 100
Freon TA ............................................................................................ 100
10% NaOH .............................................................................................0
10% Hcl .................................................................................................0
Water .....................................................................................................0
GENERAL DIRECTIONS
1. Make sure the surfaces to be bonded are clean and dry.
2. Dispense a drop or drops to one surface only. Apply only enough to leave a thin film
after compression.
3. Press parts together and hold firmly for a few seconds. Good contact is essential. An
adequate bond develops in less than one minute. (Maximum strength is attained in 24
hours.
Pg. 3 of 3
P/N 4005Z
4. Wipe off excess adhesive from the top of the container and recap. Dynatex庐 General
Purpose Adhesive, if left uncapped, may deteriorate by contamination from moisture in
the air.
5. Because Dynatex庐 General Purpose Adhesive condenses by polymerization,
sometimes whitening will occur on the surface of the container or the bonded
materials. Should this happen, wipe surfaces well with acetone.
STORAGE
Product should be stored unopened in a cool, dry place out of direct sunlight. Products
can be refrigerated for improved shelf life but should be brought back to room
temperature before use.
For safe handling information on this product, consult the Material Safety Data
Sheet (MSDS).
USERS PLEASE READ
The information and data contained herein is believed to be accurate and reliable; however, it the
user鈥檚 responsibility to determine suitable of use. Since the supplier cannot know all the uses, or
the conditions of use to which there products may be exposed, no warranties concerning the fitness
or suitability for a particular use or purpose are made.
It is the user鈥檚 responsibility to thoroughly test any proposed use of our products and independently
conclude satisfactory performance in the application.
Likewise, if the application, product specifications or manner in which our products are used require
government approval or clearance, it is the sole responsibility of the user to obtain sure
authorization.
The supplier warrants only that its products will meet its specifications. There is no use, nor any
other express or implied warranty. The users exclusive remedy and the suppliers sole liability is
limited to refund of the purchase price or replacement of any product when to be otherwise than as
warranted. The supplier will not be liable for incidental or consequential damages of any kind.
Suggestions of uses should not be taken as inducements to infringe any patents.
A division of Accumetric, LLC
350 Ring Road Elizabethtown, Kentucky 42701 USA (800) 999-2937 TEL (270) 769-5557 FAX (270) 769-6418
Outside U.S. TEL +1(270) 769-5557 FAX +1(270) 769-6418
Email: sales@dynatexinc.com Website: www.dynatexinc.com
03074005Z MADE IN U.S.A.
|