Aexcel Corporation
Material Safety Data Sheet
I. PRODUCT AND COMPANY IDENTIFICATION
Product Name: 75Y-D015
75Y-D015
Product Code:
Lane Lite Yellow Two-Component Polyester Traffic Marking Paint
Description:
Aexcel Corporation
Manufacturer:
7373 Production Drive
Mentor, OH 44060
Information: 440-974-3800
Phone Numbers:
Emergency/CHEMTREC: 800-424-9300
2 2005-05-05 16:27:58
MSDS Rev No./Date:
II. COMPOSITION/INFORMATION ON POTENTIALLY HAZARDOUS INGREDIENTS
Chemical Name CAS No. Wt % OSHA Permissible Exposure Limits (PEL)
STEL, ppm TWA, ppm
STYRENE 100-42-5 29.31 50 50
LEAD CPDS (AS PB) NONE 7.63 N.E. .05 mg/m3 (as Pb)
CHROME COMPOUNDS (AS CR03) NONE 3.6 N.E. 0.1 mg/m3 (as Cro3)
ceiling
III. HAZARDS IDENTIFICATION
HMIS Safety Ratings Health Flammability Reactivity
3* 3 1
(0 - 4, 4 = severe hazard)
Health Hazards
Skin contact, Eye contact
Routes of Entry:
Skin
Target Organs:
Immediate (Acute) Health Effects by Route of Exposure:
Harmful if inhaled.
Inhalation Irritation:
Substance may cause slight skin irritation.
Skin Contact:
Can cause minor irritation, tearing and reddening.
Eye Contact:
Overexposure to lead compounds may cause neurological, kidney and
Ingestion Irritation:
reproductive effects and anemia.Overexposure to lead compounds may cause
neurological, kidney and possible reproductive effectd and anemia.
Long-Term (Chronic) Health Effects:
See Section XV.Contains a substance(s) that is a possible reproductive system
Carcinogenicity:
Reproductive/Developmental: hazard based on high dose tests with laboratory animals.
No data available to indicate product or any components present at greater than
Mutagenicity:
0.1% is mutagenic or genotoxic.
Breathing large amounts may cause harmful effects.
Inhalation:
May cause slight irritation, burning and reddening.
Skin Contact:
Swallowing large amounts is harmful, seek medical attention. Overexposure to
Ingestion:
lead compounds may cause neurological, kidney and reproductive effects and
anemia.
75Y-D015
Page 1 of 4
Notice: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent
brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may
be harmful or fatal.
IV. FIRST-AID MEASURES
Remove to fresh air. If breathing is difficult, have a trained individual administer
Inhalation:
oxygen. If not breathing, give artificial respiration and have a trained individual
administer oxygen. Get medical attention immediately
Use an eye wash to remove a chemical from your eye regardless of the level of
Eyes:
hazard. Flush the affected eye for at least twenty minutes. Tilt the head to prevent
chemical from transferring to the uncontaminated eye. Seek medical advice after
flushing.Immediately flush eyes with plenty of water for at least 20 minutes. Get
immediate medical attention. Hold eyelids apart periodically while flushing.
Wash with soap and water. Get medical attention if irritation develops or persists.
Skin Contact:
Seek medical attention. If individual is drowsy or unconscious, do not give
Ingestion:
anything by mouth; place individual on the left side with the head down. Contact
a physician, medical facility, or poison control center for advice about whether to
induce vomiting. If possible, do not leave individual unattended.
V. FIRE FIGHTING MEASURES
Flammable88 Deg. F. TCC
Flammability Summary:
Flash Point:
Flashpoint TCC deg F Autoignition Temp UEL % in air LEL % in air
Component Parameters:
deg F
STYRENE 88 914.00 6.1 1.1
Unusual Fire & Explosive
Hazards: Styrene vapors may form explosive mixtures with air.
This polyester is one part of a two-part system of traffic safety paints. In
use, this polyester is combined with small amounts of an organic peroxide
to produce rapidly cured paint films.
Organic peroxides are unstable in the presence of heat or contaminants,
such as strong acids, strong alkalies, strong oxiders, acetone and reducing
agents. Handle these peroxides with strict attention to the peroxide
manufacturer's safety instructions.
VI. ACCIDENTAL RELEASE MEASURES
Small Spill: Eliminate all sources of ignition such as flares, flames, pilot lights, and sparks. Absorb liquid on
vermiculite, floor absorbent, or other absorbent material.
Large Spill: Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not
wearing protective equipment should be excluded from area of spill until clean-up has been completed. Stop spill at
source. Prevent from entering bare ground, drains, sewers, streams or other bodies of water. Prevent from spreading.
Pump or vacuum-transfer spilled product for recovery. Absorb unrecoverable product. Transfer contaminated
absorbent, soil and other materials to containers for disposal. Prevent run-off to bare ground, sewers, streams or other
bodies of water. If run-off occurs, notify proper authorities as required that a spill has occurred.
VII. HANDLING AND STORAGE
75Y-D015
Page 2 of 4
Handling/Storage: Containers of this material may be hazardous when emptied. Since emptied containers retain
product residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed. All
five-gallon pails and larger metal containers, including tank cars and tank trucks, should be grounded and/or bonded
when material is transferred. Emergency eyewash fountains and safety showers should be available in the
immediate vicinity of potential exposure.
VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION
Provide sufficient general and/or local exhaust ventilation to maintain exposure
Engineering Measures:
below TLV(s).
If workplace exposure limit(s) of product or any component is exceeded,
Respiratory Protection:
a NIOSH/MSHA approved air supplied respirator is advised in absence of proper
environmental control. OSHA regulations also permit other NIOSH/MSHA
respirators under specified conditions. Engineering or administrative controls
should be implemented to reduce exposure.
Wear safety glasses when handling this product.
Eye Protection:
Chemically resistant gloves
Gloves:
Control Parameters:
ACGIH TLV-TWA ppm ACGIH STEL ppm IDLH ppm
Chemical Name
STYRENE 20 100
LEAD CPDS (AS PB) .05 mg/m3 .05 mg/m3
CHROME COMPOUNDS (AS CR03) .1 mg/mg .1 mg/m3
IX. PHYSICAL AND CHEMICAL PROPERTIES
Heavy Yellow Liquid
Appearance:
11.94 lbs/gal
Bulk Density:
29.4%
Volatiles, by weight:
46.6%
Volatiles, by volume:
VP mmHg at deg F Vapor Density Evaporation Rate BP F
Component Properties:
(1 = air) (1 = n-butyl acetate) at 1 atm
STYRENE 4.5 68 7.52 0.49 293
X. STABILITY AND REACTIVITY
Stable under normal conditions.
Stability/Reactivity:
Avoid heat, sparks, open flame and other ignition sources.
Conditions to Avoid:
Strong oxidizing agents
Chemical Incompatibility:
XI. TOXICOLOGICAL INFORMATION
No data
XII. ECOLOGICAL INFORMATION
No data
XIII. DISPOSAL CONSIDERATIONS
Dispose of in accordance with all applicable local, state and federal regulations.
Disposal Methods:
XIV. TRANSPORTATION INFORMATION
Paint, Flammable Liquid
DOT Basic Description:
3
Hazard Class:
75Y-D015
Page 3 of 4
UN 1263
UN Number:
XV. REGULATORY INFORMATION
A component or components of this product are listed on the TSCA Inventory of Existing Chemical
TSCA Status:
Substances.
Chemical Name CAS # Regulation
Styrene Monomer 100-42-5 SARA 312
Lead Compounds (AS PB) NONE SARA 312
Chrome Compounds (AS CR03) NONE SARA 312
Styrene Monomer 100-42-5 SARA 313
Lead Compounds (AS PB) NONE SARA 313
Chrome Compounds (AS CR03) NONE SARA 313
Lead Compounds (AS PB) NONE CA Prop 65 - WARNING: This component known to the State
of California to cause cancer.
Chrome Compounds (AS CR03) NONE CA Prop 65 - WARNING: This component known to the State
of California to cause cancer.
Styene Monomer 100-42-5 NJ Regulated Mat'l
XVI. ADDITIONAL INFORMATION
THE INFORMATION IN THIS MATERIAL SAFETY DATA SHEET (MSDS) IS TO THE BEST
Disclaimer:
OF OUR KNOWLEDGE TRUE AND ACCURATE, BUT IS OFFERED WITHOUT WARRANTY,
EXPRESS OR IMPLIED. CONDITIONS OF USE ARE BEYOND OUR CONTROL. NEITHER
AEXCEL CORPORATION NOR ITS AGENTS SHALL BE LIABLE FOR ANY DIRECT OR
CONSEQUENTIAL INJURY, LOSS, OR DAMAGE ARISING FROM THE USE OR INABILITY
TO USE THE PRODUCT DESCRIBED HEREIN. NO PERSON IS AUTHORIZED TO MAKE ANY
STATEMENT OR RECOMMENDATION NOT CONTAINED IN THIS MSDS. ANY SUCH
STATEMENT OR RECOMMENDATION IF MADE SHALL NOT BIND THE CORPORATION.
75Y-D015
Page 4 of 4
|