POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 1 of 11
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
POLYETHER POLYOL DL-2000D
SYNONYMS
(C3-H8-O2)n.H2O, PG, "polyalkylene oxide polyol", "poly propylene glycol", "poly
propyleneglycol", "poly[oxy(methyl-1, 2-ethanediyl)], alpha-hydro-omega-hydroxy-",
"poly[oxy(methyl-1, 2-ethanediyl)], alpha-hydro-omega-hydroxy-", "polyoxypropylene
glycol", "polyoxypropylene ether", "polyether polyol", polyglycol, "1, 2-epoxypropane
polymer", "1, 2-epoxypropane polymer", "1, 2-propanediol, polymer with methyloxirane",
"1, 2-propanediol, polymer with methyloxirane", "alpha-hydro-omega-hydroxy
-poly[oxy(methyl-1, 2-ethanediyl)]", "alpha-hydro-omega-hydroxy-poly[oxy(methyl-1, 2
-ethanediyl)]"
PRODUCT USE
Hydraulic fluids, rubber lubricants, antifoam agents, intermediates in urethane foams,
adhesives, coatings, elastomers, plasticizers, paint formulations, lab reagent, solvent
for vegetable oils, waxes and resins.
SUPPLIER
Company: Quantum Chemicals Pty Ltd
Address:
70 Quantum Close
Dandenong South
Victoria 3175
Telephone: 03 8795 8000
Emergency Tel: 1300 131 001
Fax: 03 8795 8099
HAZARD RATINGS
Flammability
Toxicity
Body Contact
Reactivity
Chronic
SCALE: Min/Nil=0 Low=1 Moderate=2 High=3 Extreme=4
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 2 of 11
Section 2 - HAZARDS IDENTIFICATION
STATEMENT OF HAZARDOUS NATURE
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of
NOHSC, and the ADG Code.
POISONS SCHEDULE
None
RISK SAFETY
Harmful in contact with skin. Do not breathe gas/ fumes/ vapour/ spray.
Ingestion may produce health damage*. Avoid contact with eyes.
May produce discomfort of the eyes and skin*. Wear suitable protective clothing.
* (limited evidence). To clean the floor and all objects contaminated
by this material use water.
Keep away from food drink and animal feeding
stuffs.
Take off immediately all contaminated clothing.
In case of contact with eyes rinse with plenty
of water and contact Doctor or Poisons
Information Centre.
If swallowed IMMEDIATELY contact Doctor or
Poisons Information Centre (show this container
or label).
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
polyether polyol dl-2000d 25322-69-4 100
Section 4 - FIRST AID MEASURES
SWALLOWED
路 If swallowed do NOT induce vomiting.
路 If vomiting occurs, lean patient forward or place on left side (head-down position, if
possible) to maintain open airway and prevent aspiration.
路 Observe the patient carefully.
路 Never give liquid to a person showing signs of being sleepy or with reduced awareness;
i.e. becoming unconscious.
路 Give water to rinse out mouth, then provide liquid slowly and as much as casualty can
comfortably drink.
路 Seek medical advice.
EYE
If this product comes in contact with the eyes:
路 Wash out immediately with fresh running water.
路 Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 3 of 11
Section 4 - FIRST AID MEASURES
moving the eyelids by occasionally lifting the upper and lower lids.
路 If pain persists or recurs seek medical attention.
路 Removal of contact lenses after an eye injury should only be undertaken by skilled
personnel.
SKIN
If skin contact occurs:
路 Immediately remove all contaminated clothing, including footwear.
路 Flush skin and hair with running water (and soap if available).
路 Seek medical attention in event of irritation.
INHALED
路 If fumes or combustion products are inhaled remove from contaminated area.
路 Other measures are usually unnecessary.
NOTES TO PHYSICIAN
Treat symptomatically.
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
路 Water spray or fog.
路 Foam.
路 Dry chemical powder.
路 BCF (where regulations permit).
路 Carbon dioxide.
FIRE FIGHTING
路 Alert Fire Brigade and tell them location and nature of hazard.
路 Wear full body protective clothing with breathing apparatus.
路 Prevent, by any means available, spillage from entering drains or water course.
路 Use water delivered as a fine spray to control fire and cool adjacent area.
路 Avoid spraying water onto liquid pools.
路 DO NOT approach containers suspected to be hot.
路 Cool fire exposed containers with water spray from a protected location.
路 If safe to do so, remove containers from path of fire.
FIRE/EXPLOSION HAZARD
路 Combustible.
路 Slight fire hazard when exposed to heat or flame.
路 Heating may cause expansion or decomposition leading to violent rupture of containers.
路 On combustion, may emit toxic fumes of carbon monoxide (CO).
路 May emit acrid smoke.
路 Mists containing combustible materials may be explosive.
Combustion products include: carbon dioxide (CO2), other pyrolysis products typical of
burning organic material.
May emit poisonous fumes.
May emit corrosive fumes.
FIRE INCOMPATIBILITY
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine
bleaches, pool chlorine etc. as ignition may result.
HAZCHEM: None
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 4 of 11
Section 6 - ACCIDENTAL RELEASE MEASURES
EMERGENCY PROCEDURES
MINOR SPILLS
路 Remove all ignition sources.
路 Clean up all spills immediately.
路 Avoid breathing vapours and contact with skin and eyes.
路 Control personal contact by using protective equipment.
路 Contain and absorb spill with sand, earth, inert material or vermiculite.
路 Wipe up.
路 Place in a suitable labelled container for waste disposal.
MAJOR SPILLS
Moderate hazard.
路 Clear area of personnel and move upwind.
路 Alert Fire Brigade and tell them location and nature of hazard.
路 Wear breathing apparatus plus protective gloves.
路 Prevent, by any means available, spillage from entering drains or water course.
路 No smoking, naked lights or ignition sources.
路 Increase ventilation.
路 Stop leak if safe to do so.
路 Contain spill with sand, earth or vermiculite.
路 Collect recoverable product into labelled containers for recycling.
路 Absorb remaining product with sand, earth or vermiculite.
路 Collect solid residues and seal in labelled drums for disposal.
路 Wash area and prevent runoff into drains.
路 If contamination of drains or waterways occurs, advise emergency services.
EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all individuals could be exposed
for up to one hour WITHOUT experiencing or developing
life-threatening health effects is:
polypropylene glycol 75 mg/m鲁
irreversible or other serious effects or symptoms which could impair an individual's ability to take
protective action is:
polypropylene glycol 40 mg/m鲁
other than mild, transient adverse effects without perceiving a clearly defined odour is:
polypropylene glycol 10 mg/m鲁
The threshold concentration below which most people will experience no appreciable risk of health effects:
polypropylene glycol 10 mg/m鲁
American Industrial Hygiene Association (AIHA)
Ingredients considered according to the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 5 of 11
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
DO NOT allow clothing wet with material to stay in contact with skin.
路 Avoid all personal contact, including inhalation.
路 Wear protective clothing when risk of exposure occurs.
路 Use in a well-ventilated area.
路 Prevent concentration in hollows and sumps.
路 DO NOT enter confined spaces until atmosphere has been checked.
路 Avoid smoking, naked lights or ignition sources.
路 Avoid contact with incompatible materials.
路 When handling, DO NOT eat, drink or smoke.
路 Keep containers securely sealed when not in use.
路 Avoid physical damage to containers.
路 Always wash hands with soap and water after handling.
路 Work clothes should be laundered separately.
路 Use good occupational work practice.
路 Observe manufacturer's storing and handling recommendations.
路 Atmosphere should be regularly checked against established exposure standards to
ensure safe working conditions.
SUITABLE CONTAINER
路 Metal can or drum
路 Packaging as recommended by manufacturer.
路 Check all containers are clearly labelled and free from leaks.
STORAGE INCOMPATIBILITY
Avoid reaction with oxidising agents.
Avoid strong acids.
STORAGE REQUIREMENTS
路 Store in original containers.
路 Keep containers securely sealed.
路 No smoking, naked lights or ignition sources.
路 Store in a cool, dry, well-ventilated area.
路 Store away from incompatible materials and foodstuff containers.
路 Protect containers against physical damage and check regularly for leaks.
路 Observe manufacturer's storing and handling recommendations.
_____________________________________________________
SAFE STORAGE WITH OTHER CLASSIFIED CHEMICALS
+ X + X 0 +
_____________________________________________________
+: May be stored together
O: May be stored together with specific preventions
X: Must not be stored together
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
The following materials had no OELs on our records
鈥? polypropylene glycol: CAS:25322- 69- 4 CAS:29434- 03- 5
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 6 of 11
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
MATERIAL DATA
Sensory irritants are chemicals that produce temporary and undesirable side-effects on
the eyes, nose or throat. Historically occupational exposure standards for these
irritants have been based on observation of workers' responses to various airborne
concentrations. Present day expectations require that nearly every individual should be
protected against even minor sensory irritation and exposure standards are established
using uncertainty factors or safety factors of 5 to 10 or more. On occasion animal no
-observable-effect-levels (NOEL) are used to determine these limits where human results
are unavailable. An additional approach, typically used by the TLV committee (USA) in
determining respiratory standards for this group of chemicals, has been to assign ceiling
values (TLV C) to rapidly acting irritants and to assign short-term exposure limits (TLV
STELs) when the weight of evidence from irritation, bioaccumulation and other endpoints
combine to warrant such a limit. In contrast the MAK Commission (Germany) uses a five
-category system based on intensive odour, local irritation, and elimination half-life.
However this system is being replaced to be consistent with the European Union (EU)
Scientific Committee for Occupational Exposure Limits (SCOEL); this is more closely
allied to that of the USA.
OSHA (USA) concluded that exposure to sensory irritants can:
路 cause inflammation
路 cause increased susceptibility to other irritants and infectious agents
路 lead to permanent injury or dysfunction
路 permit greater absorption of hazardous substances and
路 acclimate the worker to the irritant warning properties of these substances thus
increasing the risk of overexposure.
CEL TWA: 10 mg/m3 (compare WEEL-TWA)
The polypropylene glycols (PPG) are not significantly irritating to the eyes or skin. The
polypropylene glycols with average molecular weights of >2000 have very low oral
toxicities and those with molecular weights of 200-1200 have moderate acute oral
toxicity. All PPGs have low chronic oral toxicity. All the PPGs have extremely low vapour
pressure and inhalation
exposure is limited to mists. Industrial exposure would not be expected to
produce central nervous system stimulant effects observed in animals fed
at high oral doses with lower molecular weight products. The workplace
environmental exposure limit (WEEL) recommended by the AIHA is that for
nuisance dusts (mists).
PERSONAL PROTECTION
EYE
路 Safety glasses with side shields.
路 Chemical goggles.
路 Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens or
restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account
of injury experience. Medical and first-aid personnel should be trained in their removal
and suitable equipment should be readily available. In the event of chemical exposure,
begin eye irrigation immediately and remove contact lens as soon as practicable. Lens
should be removed at the first signs of eye redness or irritation - lens should be
removed in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 7 of 11
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
HANDS/FEET
#726#72glove#76a-p()
OTHER
路 Overalls.
路 P.V.C. apron.
路 Barrier cream.
路 Skin cleansing cream.
路 Eye wash unit.
RESPIRATOR
Selection of the Class and Type of respirator will depend upon the level of breathing
zone contaminant and the chemical nature of the contaminant. Protection Factors (defined
as the ratio of contaminant outside and inside the mask) may also be important.
Breathing Zone Level Maximum Protection Half- face Respirator Full- Face Respirator
ppm (volume) Factor
1000 10 A- AUS P -
1000 50 - A- AUS P
5000 50 Airline * -
5000 100 - A- 2 P
10000 100 - A- 3 P
100+ Airline**
* - Continuous Flow ** - Continuous-flow or positive pressure demand.
The local concentration of material, quantity and conditions of use determine the type of
personal protective equipment required.
For further information consult site specific
CHEMWATCH data (if available), or your
Occupational Health and Safety Advisor.
ENGINEERING CONTROLS
General exhaust is adequate under normal operating conditions. Local exhaust ventilation
may be required in specific circumstances. If risk of overexposure exists, wear approved
respirator. Correct fit is essential to obtain adequate protection. Provide adequate
ventilation in warehouse or closed storage areas. Air contaminants generated in the
workplace possess varying "escape" velocities which, in turn, determine the "capture
velocities" of fresh circulating air required to effectively remove the contaminant.
Type of Contaminant: Air Speed:
solvent, vapours, degreasing etc., evaporating 0.25- 0.5 m/s (50- 100 f/min)
from tank (in still air).
aerosols, fumes from pouring operations, 0.5- 1 m/s (100- 200 f/min.)
intermittent container filling, low speed
conveyer transfers, welding, spray drift,
plating acid fumes, pickling (released at low
velocity into zone of active generation)
direct spray, spray painting in shallow booths, 1- 2.5 m/s (200- 500 f/min.)
drum filling, conveyer loading, crusher dusts,
gas discharge (active generation into zone of
rapid air motion)
grinding, abrasive blasting, tumbling, high 2.5- 10 m/s (500- 2000 f/min.)
speed wheel generated dusts (released at high
initial velocity into zone of very high rapid
air motion).
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 8 of 11
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Within each range the appropriate value depends on:
Lower end of the range Upper end of the range
1: Room air currents minimal or favourable to 1: Disturbing room air currents
capture
2: Contaminants of low toxicity or of nuisance 2: Contaminants of high toxicity
value only.
3: Intermittent, low production. 3: High production, heavy use
4: Large hood or large air mass in motion 4: Small hood- local control only
Simple theory shows that air velocity falls rapidly with distance away from the opening
of a simple extraction pipe. Velocity generally decreases with the square of distance
from the extraction point (in simple cases). Therefore the air speed at the extraction
point should be adjusted, accordingly, after reference to distance from the contaminating
source. The air velocity at the extraction fan, for example, should be a minimum of 1-2
m/s (200-400 f/min) for extraction of solvents generated in a tank 2 meters distant from
the extraction point. Other mechanical considerations, producing performance deficits
within the extraction apparatus, make it essential that theoretical air velocities are
multiplied by factors of 10 or more when extraction systems are installed or used.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Family of products which vary in their physical properties as a result of variations in
production. Data presented here is for typical family member. Colourless liquid with a
sweet, faint odour. Classified by molecular weight as 425, 1025, 2025, 3025, 4025. Lower
molecular weight grades are lower viscosity and soluble in water. High molecular grades
are viscous.
PHYSICAL PROPERTIES
Liquid.
Mixes with water.
Molecular Weight: Not applicable. Boiling Range (掳C): 133 (typical).
Melting Range (掳C): - 60 (typical). Specific Gravity (water=1): 1 approx.
Solubility in water (g/L): Miscible pH (as supplied): Not applicable
pH (1% solution): Not available. Vapour Pressure (kPa): Not available.
Volatile Component (%vol): 100 approx. Evaporation Rate: Not available
Relative Vapour Density (air=1): Not available. Flash Point (掳C): 185
Lower Explosive Limit (%): Not available. Upper Explosive Limit (%): Not available.
Autoignition Temp (掳C): 201 Decomposition Temp (掳C): Not available.
State: Liquid Viscosity: Not Available
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
路 Presence of incompatible materials.
路 Product is considered stable.
路 Hazardous polymerisation will not occur.
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 9 of 11
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
Accidental ingestion of the material may be damaging to the health of the individual.
Adverse effects associated with the administration of central nervous system stimulants
include labored breathing, coughing, narrowed airways, chest tightness, and throat spasm.
Muscular involvement may produce contraction of small localised muscle fibres (visible
through the skin) or seizures. Headache, dizziness, fever and confusion may also result.
Other symptoms may include nausea, vomiting, diarrhoea and difficulty in urination,
alterations in blood pressure and irregular heart beat.
EYE
Limited evidence or practical experience suggests, that the material may cause eye
irritation in a substantial number of individuals. Prolonged eye contact may cause
inflammation characterised by a temporary redness of the conjunctiva (similar to
windburn).
SKIN
Skin contact with the material may be harmful; systemic effects may result following
absorption.
There is some evidence to suggest that the material may cause moderate inflammation of
the skin either following direct contact or after a delay of some time. Repeated exposure
can cause contact dermatitis which is characterised by redness, swelling and blistering.
Entry into the blood-stream, through, for example, cuts, abrasions or lesions, may
produce systemic injury with harmful effects. Examine the skin prior to the use of the
material and ensure that any external damage is suitably protected.
INHALED
The material is not thought to produce either adverse health effects or irritation of the
respiratory tract following inhalation (as classified by EC Directives using animal
models). Nevertheless, adverse systemic effects have been produced following exposure of
animals by at least one other route and good hygiene practice requires that exposure be
kept to a minimum and that suitable control measures be used in an occupational setting.
CHRONIC HEALTH EFFECTS
Long-term exposure to the product is not thought to produce chronic effects adverse to
the health (as classified by EC Directives using animal models); nevertheless exposure by
all routes should be minimised as a matter of course.
TOXICITY AND IRRITATION
unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances.
TOXICITY IRRITATION
Oral (rat) LD50: 9760 mg/kg Skin (rabbit): 500 mg Mild
Oral (Rat) LD50: 2410 mg/kg **
Dermal (Rabbit) LD50: 500 mg/kg **
The material may be irritating to the eye, with prolonged contact causing inflammation.
Repeated or prolonged exposure to irritants may produce conjunctivitis.
The material may cause skin irritation after prolonged or repeated exposure and may
produce on contact skin redness, swelling, the production of vesicles, scaling and
thickening of the skin.
** Rohm and Haas Paraplex WP-1 MSDS
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 10 of 11
Section 12 - ECOLOGICAL INFORMATION
Fish LC50 (96hr.) (mg/l): 650- 1700
DO NOT discharge into sewer or waterways.
Ecotoxicity
Fish LC50: 1000 mg/l
Daphnia magna EC50: 4000 mg/l
Anaerobic effects: no degradradataion
Degradation Biological: only with synth. sewage
Section 13 - DISPOSAL CONSIDERATIONS
路 Containers may still present a chemical hazard/ danger when empty.
路 Return to supplier for reuse/ recycling if possible.
Otherwise:
路 If container can not be cleaned sufficiently well to ensure that residuals do not
remain or if the container cannot be used to store the same product, then puncture
containers, to prevent re-use, and bury at an authorised landfill.
路 Where possible retain label warnings and MSDS and observe all notices pertaining to the
product.
Legislation addressing waste disposal requirements may differ by country, state and/ or
territory. Each user must refer to laws operating in their area. In some areas, certain
wastes must be tracked.
A Hierarchy of Controls seems to be common - the user should investigate:
路 Reduction,
路 Reuse
路 Recycling
路 Disposal (if all else fails)
This material may be recycled if unused, or if it has not been contaminated so as to make
it unsuitable for its intended use. If it has been contaminated, it may be possible to
reclaim the product by filtration, distillation or some other means. Shelf life
considerations should also be applied in making decisions of this type. Note that
properties of a material may change in use, and recycling or reuse may not always be
appropriate.
DO NOT allow wash water from cleaning or process equipment to enter drains.
It may be necessary to collect all wash water for treatment before disposal.
In all cases disposal to sewer may be subject to local laws and regulations and these
should be considered first. Where in doubt contact the responsible authority.
路 Recycle wherever possible or consult manufacturer for recycling options.
路 Consult State Land Waste Authority for disposal.
路 Bury or incinerate residue at an approved site.
路 Recycle containers if possible, or dispose of in an authorised landfill.
Section 14 - TRANSPORTATION INFORMATION
HAZCHEM: None
NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN, IATA,
IMDG
POLYETHER POLYOL DL-2000D
Chemwatch Material Safety Data Sheet (REVIEW)
Issue Date: 15-Jul-2007 CHEMWATCH 24770
NC317TCP Version No:4
CD 2007/3 Page 11 of 11
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE: None
REGULATIONS
polypropylene glycol (CAS: 25322-69-4) is found on the following regulatory lists;
Australia Inventory of Chemical Substances (AICS)
No data available for polypropylene glycol as CAS: 29434-03-5.
Section 16 - OTHER INFORMATION
INGREDIENTS WITH MULTIPLE CAS NUMBERS
Ingredient Name CAS
polypropylene glycol 25322- 69- 4, 29434- 03- 5
MSDS SECTION CHANGES
The following table displays the version number of and date on which each section was last changed.
Section Name Version Date Section Name Version Date Section Name Version Date
First Aid 4 15- Jul- 2007 Exposure Standard 4 15- Jul- 2007 Acute Health 4 15- Jul- 2007
(swallowed) (skin)
Fire Fighter (fire 4 15- Jul- 2007 Personal 4 15- Jul- 2007 Acute Health 4 15- Jul- 2007
fighting) Protection (eye) (swallowed)
Fire Fighter 4 15- Jul- 2007 Personal 4 15- Jul- 2007 Chronic Health 4 15- Jul- 2007
(fire/explosion Protection
hazard) (hands/feet)
Spills (major) 4 15- Jul- 2007 Personal 4 15- Jul- 2007 Toxicity and 4 15- Jul- 2007
Protection (other) Irritation (Other)
Handling Procedure 4 15- Jul- 2007 Physical 4 15- Jul- 2007 Toxicity and 4 15- Jul- 2007
Properties Irritation
(Toxicity Figure)
Storage (storage 4 15- Jul- 2007 Acute Health (eye) 4 15- Jul- 2007 Environmental 4 15- Jul- 2007
incompatibility)
Engineering 4 15- Jul- 2007 Acute Health 4 15- Jul- 2007 Disposal 4 15- Jul- 2007
Control (inhaled)
Classification of the preparation and its individual components has drawn on official and
authoritative sources as well as independent review by the Chemwatch Classification
committee using available literature references.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written permission
from CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 15-Jul-2007
Print Date: 2-Jan-2008
|