MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK OG175 BILLERICA, MA 01821
Single Component
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 (978) 667 3805
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 2/15/01
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: NA.
VAPOR DENSITY: NA EVAPORATION RATE:
APPEARANCE: Clear Liquid SPECIFIC GRAVITY: NA
ODOR: Slight
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
There are no hazardous ingredients that require reporting per OSHA鈥檚 Hazardous Communication Standards or by Sara
Title III.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200 F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide. Water may be ineffective.
UNUSUAL FIRE & EXPLOSION HAZARDS: Vapors may flow along surfaces to distant ignition sources and flash back. Closed
containers exposed to heat may explode.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal protective equipment.
Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat, sources of ignition, flame. Direct sunlight will polymerize adhesive
MATERIALS TO AVOID: Strong acids or alkalies
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon monoxide,
and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from sources believed to
be reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No warranty,
guarantee, or representation is made as to the correctness or sufficiency of the information. The user of this product must
decide what measures are necessary to safely use this product, either alone or in the combination with other products, and to
determine its environmental compliance obligations under applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK OG175
EFFECTS OF OVER EXPOSURE
INGESTION: No specific information available.
INHALATION: Prolonged breathing of vapor may be irritating and may cause nausea
and vomiting.
SKIN CONTACT: Can cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: Combinations of the above conditions can
be experienced.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area. Absorb
spillage with inert material and dispose. Wear self contained breathing apparatus.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations. Do not
discharge into natural water sources.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed when not in
use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water after handling. Solvents
should not be used to clean skin because of increased penetration potential - protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK OG175 TEL: (978) 667 鈥? 3805
DATE REVISED: 2/15/01
REV: A
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency
Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or implied is
made with respect to this information.
|