MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK T7109-14, Part A BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH-2 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 4/4/2006
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE: NA
APPEARANCE: White Paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT%
Bisphenol F 28064-14-4 15-35%
Isopropylidenebisphenol 71033-08-4 25-50%
Bisphenol F and Isopropylidenebisphenol both require reporting according to OSHA Communication Standards under 29CFR,
1910.1200.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal protective equipment.
Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon monoxide,
and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from sources believed to
be reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No warranty,
guarantee, or representation is made as to the correctness or sufficiency of the information. The user of this product must decide
what measures are necessary to safely use this product, either alone or in combination with other products, and to determine its
environmental regulatory compliance obligations under applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK T7109-14, Part A
EFFECTS OF OVEREXPOSURE
INGESTION: May be moderately toxic. Ingestion can severely upset the gastric
system
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory irritation.
SKIN CONTACT: Can cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC/ACUTE EFFECTS OF EXPOSURE: Can cause dermatitis and sensitization.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush well with water. Get medical attention
immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever high level
exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed when not in
use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water after handling. Solvents
should not be used to clean skin because of increased penetration potential - protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK T7109-14, Part B BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 1 FIRE-1 REACTIVITY- 1 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 4/4/2006
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: mild
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Clear liquid SPECIFIC GRAVITY: 1.10
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
There are no hazardous ingredients that require reporting according to Mass RTK or by OSHA Communication Standards.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >210C
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal protective
equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides of nitrogen,
carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from sources believed to
represent current opinion on the subject when the msds was prepared. No warranty, guarantee or representation is made as to the
correctness or sufficiency of the information. The user of this product must decide what safety measures are necessary to safely
use this product, whether alone or in combination with other products, and determine its environmental regulatory compliance
obligations under under applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK T7109-14, Part B
EFFECTS OF OVEREXPOSURE
INGESTION: Contains materials that may be moderately toxic. Ingestion can
severely upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: May cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC/ACUTE EFFECTS OF EXPOSURE: Combinations of above conditions may be
experienced.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush well with water. Get medical attention
immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever high level
exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed when not in
use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water after handling. Solvents
should not be used to clean skin because of increased penetration potential - protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION
EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK T7109-14 TEL: (978) 667 鈥? 3805
DATE REVISED: 4/4/2006
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning
and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Part A
Not Restricted
Part B
Not Restricted
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or implied is
made with respect to this information.
|