MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK T6067 BILLERICA, MA 01821
Single Component
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 1 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 02/04/2004
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: <0.5 VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Opaque Paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT % TOXICITY DATA
Bisphenol F 28064-14-4 15-35% See Ingredient Sheet 708003
Diuron 330-54-1 < 15 N/A
Bisphenol F and Diuron are the only hazardous ingredients that require reporting under OSHA Communication
Standards, under 29CFR, 1910.1200.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, carbon dioxide, and oxides of nitrogen.
____________________________________________________________________________________________
The information and recommendations contained in this MSDS have been compiled from sources believed to be
reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No
warranty, guarantee, or representation is made as to the correctness or sufficiency of the information. The user of
this product must decide what measures are necessary to safely use this product, either alone or in combination with
other products, and to determine its environmental regulatory compliance obligations under applicable federal or state
laws.
V. HEALTH HAZARD DATA EPO-TEK T6067
EFFECTS OF OVEREXPOSURE
INGESTION: No specific information available. Contains materials that
may be moderately toxic.
INHALATION: No specific information available. Hot vapors could cause headaches,
nausea, dizziness, and respiratory irritation, if inhaled.
SKIN CONTACT: May cause dermatitis in some individuals.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: No specific information available.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear a NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream, applied before exposure, and gloves is recommended. Do not apply
cream after exposure.
EYE PROTECTION: Chemical splash goggles recommended where applicable.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers
closed when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly
with soap and water after handling. Solvents should not be used to clean skin because of increased
penetration potential.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK T6067 TEL: (978) 667 鈥? 3805
DATE ISSUED: 02/04/2004
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
INGREDIENT SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
EMERGENCY PHONE:
INGREDIENT CODE NUMBER: 110201 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
*HMIS: HEALTH (2) FLAMMIBILITY (1) DATE ISSUED: 8/18/00
REACTIVITY (0)
CARCINOGEN: NTP (No) IARC (No) OSHA (No)
*HMIS CODE rating are estimated by Epoxy Technology
I. IDENTIFICATION & PHYSICAL DATA
Color: Clear
Odor: Slight
Physical State: Liquid
Solubility in Water: Insoluable
Vapor Pressure: <0.01 mm Hg@20掳C
Specific Gravity: 1.19
Boiling Point: >200掳C
II. HAZARDOUS INGREDIENTS WT% CAS
Bisphenol F 100% 28064-14-4
TOXICITY DATA
Acute Oral Effects (LD50): Rat: > 10,000mg/kg
Acute Dermal Toxity (LD50): Rabbit: 3,000mg
Inhalation Toxicity (LC50): LCLO=1.7mg
III. FIRE AND EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Carbon dioxide, foam, dry chemical, water spray.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Decomposition and combustion products may be toxic.
FIRE FIGHTING EQUIPMENT: Use self-contained breathing apparatus.
IV. REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Avoid strong acids or bases in bulk and elevated temperatures.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide, aldehydes.
HAZARDOUS POLYMERIZATION: Will not occur
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to represent current opinion on the subject when the msds was prepared. No warranty, guarantee
or representation is made as to the correctness or sufficiency of the information. The user of this product, must
decide what safety measures are necessary to safely use this product, whether alone or in combination with other
products, and determine its environmental regulatory compliance obligations under applicable federal or state laws.
110201
V. HEALTH HAZARD DATA
EFFECTS OF OVER EXPOSURE
INGESTION: No specific information available.
INHALATION: No specific information available.
SKIN CONTACT: May cause skin irritation, dermatitis.
EYE CONTACT: Irritating to the eyes. May cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: May cause dermatitis if it gets on your skin.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes. Get
medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Avoid personal contact. Take up with
absorbent material and shovel into a closed container.
WASTE DISPOSAL METHOD: Employ waste disposal procedures that are in accordance with
federal, state and local regulations.
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever exposure to air born
vapors are anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves-neoprene or equivalent. A combination of barrier
cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a face shield
and impervious apron. A safety shower and eye wash facility should be available.
_____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors generated by heating.
Keep containers closed when not in use. Remove all contaminated clothing and wash.
|