MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: Epo Tek T6116R BILLERICA, MA 01821
INGREDIENT CODE NUMBER: Not applicable
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE- 1 REACTIVITY- 1 (978) 667 3805
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 7/7/00
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Opaque paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
Bisphenol F 28064-14-4 15-30% See Ingredient Sheet 708003.
Bispjhenol F is the only ingredient that requires reporting under OSHA鈥檚 Hazardous Communication Standards, 29
CFR 1910.1200.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: NA
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include
carbon monoxide, carbon dioxide, and oxides of nitrogen.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS
was prepared. No warranty, guarantee or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what safety measures are necessary to safely use this product,
either alone or in the combination with other products, and determine its environmental regulatory compliance
obligations under any applicable federal or state laws.
V. HEALTH HAZARD DATA Epo Tek T6116R
EFFECTS OF OVER EXPOSURE
INGESTION: Contains materials that may be moderately toxic.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation.
SKIN CONTACT: Can cause irritation and dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: No specific information available.
Can cause dermatitis and sensitization
____________________________________________________________________________________________
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION
EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: T6116R TEL: (978) 667 鈥? 3805
DATE ISSUED: 7/7/00
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed
or implied is made with respect to this information.
|