MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: Epo Tek T7139, Part A BILLERICA, MA 01821
INGREDIENT CODE NUMBER: Not applicable
EMERGENCY PHONE:
*HMIS: HEALTH- 3 FIRE-2 REACTIVITY- 1 US/CANADA: 800-255-3924
*ANSI CODE: 3 INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 2/7/06
REV: A
* HMIS and ANSI CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: <2 % VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Opaque paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
1,4 Butanedioldiglycidyl Ether 2425-79-8 <10 NA
Silica 14808-60-7 <23% NA
Silica is the only hazardous ingredient that requires reporting, according to OSHA 29CFR 1910.1000.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: NA
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, carbon dioxide, and oxides of nitrogen.
____________________________________________________________________________________________
To the best of our knowledge, the information contained herein is accurate. Epoxy Technology Inc., however,
assumes no liability for the accuracy or completeness of the information contained herein. Final determination of
suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and
should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the
only hazards which exist.
V. HEALTH HAZARD DATA Epo Tek T7139, Part A
EFFECTS OF OVER EXPOSURE
INGESTION: Contains materials that may be moderately toxic.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation.
SKIN CONTACT: Can cause irritation and dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: No specific information available.
Can cause dermatitis and sensitization
____________________________________________________________________________________________
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: Epo Tek T7139, Part B BILLERICA, MA 01821
INGREDIENT CODE NUMBER: Not applicable
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 1 US/CANADA: 800-255-3924
*ANSI CODE: 2 INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 2/7/06
REV: A
* HMIS and ANSI CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Amber Liquid SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
There are no hazardous ingredients that require reporting according to OSHA 29CFR standards, or by Mass RTK.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides
of nitrogen, carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
To the best of our knowledge, the information contained herein is accurate. Epoxy Technology Inc., however,
assumes no liability for the accuracy or completeness of the information contained herein. Final determination of
suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and
should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the
only hazards which exist.
V. HEALTH HAZARD DATA Epo Tek T7139, Part B
EFFECTS OF OVER EXPOSURE
INGESTION: Contains materials that may be moderately toxic. Ingestion can
severely upset the gastric system.
INHALATION: Can cause respiratory irritation and sensitization. This type of contact
can be avoided by the use of local, exhaust ventilation.
SKIN CONTACT: May cause dermatitis and sensitization. This type of exposure is
avoidable by the use of local, exhaust ventilation, adequate clothing, gloves and
chemical splash goggles.
EYE CONTACT: Irritating to the eyes. Can cause injury. This type of exposure is
avoidable by the use of local, exhaust ventilation, adequate clothing, gloves and
chemical splash goggles.
CHRONIC EFFECTS OF OVER EXPOSURE: May cause dermatitis and sensitization.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In event of eye contact, flush well with water and get medical attention
immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Can be irritating to respiratory tract.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear a NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Local exhaust ventilation recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: This type of contact can be avoided through the use of Chemical
splash goggles.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye must be located in close
proximity to work and handling areas.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers
closed when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly
with soap and water after handling. Solvents should not be used to clean skin because of increased
penetration potential - protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION
EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: T7139 TEL: (978) 667 鈥? 3805
DATE REVISED: 2/7/06
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Part A
Not Restricted
Part B
Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
|