MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK P1011 BILLERICA, MA 01821
Single Component
EMERGENCY PHONE:
*HMIS: HEALTH- 3 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 5/22/2007
REV: D
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Silver Paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT %
Silver Flake 7440-22-4 55-75%
Diglycidyl Ether of Bisphenol A 001675-54-3 <10%
1-Cyclohexyl-2-Pyrrolidinone 6837-24-7 < 30%
1-(2-Hydroxyethyl)-2-Pyrrolidinone 3445-11-2 < 10%
Silver Flake requires reporting per Sara Title III, under section 313. Diglycidyl Ether of Bisphenol A, 1-Cyclohexyl-2-
Pyrrolidinone and 1-(2-Hydroxyethyl)-2-Pyrrolidinone are the only hazardous ingredients that require reporting
according to OSHA鈥檚 Hazardous Communication Standards or by Mass RTK.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, carbon dioxide, and oxides of nitrogen.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion o the subject when the MSDS
was prepared. No warranty, guarantee, or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what measures are necessary to safely use this product, either
alone or in the combination with other products, and to determine its environmental the combination with other
products, and to determine its environmental regulatory compliance obligations under applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK P1011
EFFECTS OF OVER EXPOSURE
INGESTION: Contains materials that may be moderately toxic.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory irritation.
SKIN CONTACT: Can cause irritation and dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: No specific information available.
Can cause dermatitis and sensitization
____________________________________________________________________________________________
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
______________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK P1011 Tel: (978) 667-3805
DATE REVISED: 5/22/2007
REV: D
SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): Silver Flake as listed above.
1. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
2. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
3. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
4. Transportation
Proper Shipping Name: Corrosive liquids, N.O.S (1-Cyclohexyl-2-Pyrrolidone)
Hazard Class: 8
Packing Group: II
ID Number: UN1760
Transport Label(s): Corrosive Liquid
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
|