MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK T905BN-2, Part A BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 1 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 03/25/2004
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Opaque paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
Reaction product of epichlorohydrin & bisphenol A 025085-99-8 5-30% See Ingredient Sheet 110104
Reaction product of epichlorohydrin and bisphenol A requires reporting according to OSHA鈥檚 Communication
Standards.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: > 220 F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this MSDS have been compiled from sources believed to be
reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No
warranty, guarantee, or representation is made as to the correctness or sufficiency of the information. The user of
this product must decide what measures are necessary to safely use this product, either alone or in combination with
other products, and to determine its environmental regulatory compliance obligations under applicable federal or state
laws.
V. HEALTH HAZARD DATA EPO-TEK T905BN-2, Part A
EFFECTS OF OVER EXPOSURE
INGESTION: May be toxic. Will cause gastric disturbances.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory irritation.
SKIN CONTACT: Contains corrosive constituent. Can cause dermatitis.
EYE CONTACT: Contains corrosive constituent. Irritating to the eyes. Can cause
injury.
CHRONIC EFFECTS OF OVER EXPOSURE: Can cause dermatitis and sensitization.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK T905-BN2, Part B BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 3 FIRE-1 REACTIVITY- 1 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 03/25/2004
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: <.1 mm Hg @20C
BOILING POINT: NA SOLUBILITY IN WATER: Moderate
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Dark Liquid SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA
Cycloaliphatic-Aromatic Polyamine Trade Secret 90% See Ingredient Sheet 708008.
Cycloaliphatic-Aromatic is the only hazardous ingredient that needs reporting, according to OSHA Hazard
Communication Standard 29CFR 1910.1200.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides
of nitrogen, carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this MSDS have been compiled from sources believed to be
reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No
warranty, guarantee, or representation is made as to the correctness or sufficiency of the information. The user of
this product must decide what measures are necessary to safely use this product, either alone or in the combination
with other products, and to determine its environmental regulatory compliance obligations under applicable federal or
state laws.
V. HEALTH HAZARD DATA EPO-TEK T905BN-2, Part B
EFFECTS OF OVER EXPOSURE
INGESTION: Contains materials that may be slightly toxic. Ingestion can
moderately upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: May cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause severe injury.
CHRONIC EFFECTS OF OVER EXPOSURE: See attached Ingredient Sheet
708008.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust is essential for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK T905-BN2 TEL: (978) 667 鈥? 3805
DATE REVISED: 11/9/2006
REV: B
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Part A
Not Restricted
Part B
Proper Shipping Name: Polyamines, Liquid, Corrosive, N.O.S. (Diethylenetriamine, Cycloaliphatic Polyamine)
Hazardous Class: 8
Packing Group: II
ID Number: UN2735
Transport Label(s): Corrosive Liquid
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
INGREDIENT SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
EMERGENCY PHONE:
INGREDIENT CODE NUMBER: 110104 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
*HMIS: HEALTH (1) FLAMMIBILITY (1) DATE REVISED: 10/13/00
REACTIVITY (0) REV: A
CARCINOGEN: NTP (No) IARC (No) OSHA (No)
*HMIS CODE rating are estimated by Epoxy Technology
I. IDENTIFICATION & PHYSICAL DATA
Color: Colorless to slight Yellow
Odor: Slight
Physical State: Liquid
Solubility in Water: None
Vapor Pressure: NA
Specific Gravity: 1.16
Boiling Point: NA
II. HAZARDOUS INGREDIENTS WT% CAS #
Reaction product of epichlorohydrin & Bisphenol A 100% 025085-99-8
TOXICITY DATA
Skin(LD50): in rabbits is 20,000mg/kg.
Ingestion(LD50): in rats is >5000mg/kg
Mutagenicity: Animal mutagenicity, studies were negative.
III. FIRE AND EXPLOSION DATA
FLASH POINT: 485 F
EXTINGUISHING MEDIA: Foam, CO2, dry chemical.
UNUSUAL FIRE AND EXPLOSION HAZARDS: None Known
FIRE FIGHTING EQUIPMENT: Wear positive pressure self-contained breathing apparatus and full protective
equipment.
IV. REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Avoid storage at high temperatures.
HAZARDOUS DECOMPOSITION PRODUCTS: None Known.
HAZARDOUS POLYMERIZATION: Will not occur
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to represent current opinion on the subject when the MSDS was prepared. No warranty, guarantee
or representation is made as to the correctness or sufficiency of the information. The user of this product must
decide what safety measures are necessary to safely use this product, whether alone or in combination with other
products, and determine its environmental regulatory compliance obligations under applicable federal or state laws.
V. HEALTH HAZARD DATA 110104
EFFECTS OF OVER EXPOSURE
None Established.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: Flush eyes with plenty of water.
SKIN CONTACT: Wash off in flowing water or shower.
INGESTION: No adverse effects anticipated by this route of exposure incidental to proper
industrial handling.
INHALATION: No adverse effects anticipated by this route of exposure.
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Soak up in absorbent material such as
sand, or polypropylene or polyethylene fiber products and collect in suitable containers. Residual
resin may be removed using steam or hot soapy water.
WASTE DISPOSAL METHOD: Employ waste disposal procedures that are in accordance with
federal, state and local regulations.
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever exposure to air born
vapors are anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves-neoprene or equivalent. A combination of barrier
cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a face shield
and impervious apron. A safety shower and eye wash facility should be available.
_____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors generated by heating.
Keep containers closed when not in use. Remove all contaminated clothing and wash.
INGREDIENT SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: Cycloaliphatic-Aromatic Polyamine EMERGENCY PHONE:
INGREDIENT CODE NUMBER: 708008 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
*HMIS: HEALTH (3) FLAMMIBILITY (1) DATE ISSUED: 1/6/00
REACTIVITY (0)
CARCINOGEN: NTP (No) IARC (No) OSHA (No)
*HMIS CODE rating are estimated by Epoxy Technology
II. IDENTIFICATION & PHYSICAL DATA
Color: Brown
Odor: Amine
Physical State: Viscous Liquid
Solubility in Water: Slight
Vapor Pressure: Not Determined
Specific Gravity: 8.7lb/gal@25C
Boiling Point: Not determined
II. HAZARDOUS INGREDIENTS WT% CAS #
Cycloaliphatic-Aromatic Polyamine 100% Trade Secret
TOXICITY DATA
Oral: LD50Lrat:50-1080mg/kg
Inhalation: LC50:Rat LCLO=750mg/m3/10min
Dermal Toxicity LD50: Rabbit 1110-1280mg/kg
IV. FIRE AND EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Wear a NIOSH approved self-contained breathing respirator. Use water spray to cool
containers exposed to fire. Containers may explode in heat of fire.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Dangerous fire and explosion hazard when exposed to heat or
flame.
FIRE FIGHTING EQUIPMENT: Use carbon dioxide, foam, dry chemical, and water spray after moving all ignition.
IV. REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Avoid storage at high temperatures.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide, aldehydes, and nitrogen oxides.
HAZARDOUS POLYMERIZATION: Will not occur
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS
was prepared. No warranty, guarantee, or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what measures are necessary to safely use this product, either
alone or in the combination with other products, and to determine its environmental regulatory compliance obligations
under applicable federal or state laws.
IX. HEALTH HAZARD DATA 708008
EFFECTS OF OVER EXPOSURE
INGESTION: May be harmful by ingestion. Irritating the gastro intestinal tract.
INHALATION: May be harmful by inhalation. Irritating to the respiratory tract.
SKIN CONTACT: Severe irritation to the skin.
EYE CONTACT: Irritating to the eyes. May cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: May cause headaches and irritate
respiratory tract.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes. Get
medical attention immediately.
SKIN CONTACT: Wash immediately with plenty of soap and water. Take off
contaminated clothing and shoes.
INGESTION: Remove visible material, clean the face with water; lay down quiet and seek
medical advice immediately.
INHALATION: Remove employee to fresh air. If not breathing, give artificial respiration.
If breathing is difficult, give oxygen Call a physician.
X. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Avoid personal contact. Take up with
absorbent material and shovel into a closed container.
WASTE DISPOSAL METHOD: Employ waste disposal procedures that are in accordance with
federal, state and local regulations.
XI. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever exposure to air born
vapors are anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves-neoprene or equivalent. A combination of barrier
cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a face shield
and impervious apron. A safety shower and eye wash facility should be available.
_____________________________________________________________________________________________
XII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors generated by heating.
Keep containers closed when not in use. Remove all contaminated clothing and wash.
|