MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK OH105, Part A BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 2/7/2006
* HMIS CODE ratings are estimated by Epoxy Technology. REV: C
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Black Paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT %
Reaction product of epichlorohydrin & bisphenol A 025085-99-8 45-65%
1,4 Butanediol Diglycidyl Ether 2425-79-8 15-35%
Carbon Black, Amorphous 1333-86-4 15-30%
Reaction product of epichlorohydrin & bisphenol A and carbon black, amorphous are considered hazardous
according to OSHA鈥檚 Hazardous Communication Standards, 29CFR, 1910.1200. 1,4 Butanediol Diglycidyl Ether
requires reporting according to Sara Title III, under sections 311 and 312.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendation contained in this Material Safety Data Sheet have been compiled from sources
believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS was
prepared. No warranty, guarantee, or representation is made as to the correctness or sufficiency of the information.
The user of this product must decide what measures are necessary to safely use this product, either alone or in
combination with other products, and to determine its environmental regulatory compliance obligations under
applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK OH105, Part A
EFFECTS OF OVER EXPOSURE
IINGESTION: Contains materials that may be moderately toxic. Ingestion can
severely upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: Contains corrosive material; may cause skin damage with burns
and blistering.
EYE CONTACT: Moderately irritating with possible permanent eye injury.
CHRONIC EFFECTS OF OVER EXPOSURE: Combinations of above conditions can be
experienced.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH-approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK OH105, Part B BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 3 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 2/7/2006
REV: C
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: NA
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Amber liquid SPECIFIC GRAVITY: 1.02
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT %
Imidazole 288-32-4 25-50% .
Imidazole is the only hazardous ingredient that requires reporting per Sara Title III, under 311 and 312.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides
of nitrogen, carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendation contained in this MSDS have been compiled from sources believed to be
reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No
warranty, guarantee or representation is made as to the correctness or sufficiency of the information. The user of this
product must decide what safety measures are necessary to safely use this product, either alone or in combination
with other products, and determine its environmental regulatory compliance obligations under any applicable federal
or state laws.
V. HEALTH HAZARD DATA EPO-TEK OH105, Part B
EFFECTS OF OVEREXPOSURE
INGESTION: Ingestion can severely upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory irritation, if
inhaled.
SKIN CONTACT: Mildly irritating in rabbit dermal irritation studies. May cause
dermatitis and skin sensitization in some individuals.
EYE CONTACT: Causes eye burns in rabbit irritation studies. Irritating to the eyes.
Can cause injury.
CHRONIC EFFECTS OF OVEREXPOSURE: Repeated and/or prolonged exposures may result in:
adverse
Respiratory effects( such as cough, tightness of chest or shortness of breath), adverse eye effects
(such as
Conjunctivitis corneal damage), adverse eye effects (such as rash, irritation or corrosion).
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed when
not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water after
handling. Solvents should not be used to clean skin because of increased penetration potential - protective skin oils
can be dissolved by solvents
REGULATORY INFORMATION
EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK OH105 TEL: (978) 667 鈥? 3805
DATE REVISED: 6/26/2006
REV: D
1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
2. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
3. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
4. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
5. Transportation
Part A
Not Restricted
Part B
Proper Shipping Name: Corrosive, Liquid, Basic, Organic, N.O.S (Imidazole)
Hazard Class: 8
Packing Group: III
ID Number: UN3267
Transport Label(s): Corrosive Liquid
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
|