MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK OM100 BILLERICA, MA 01821
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 EMERGENCY PHONE:
US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 03/07/2003
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE:
APPEARANCE: Clear liquid SPECIFIC GRAVITY: NA
ODOR: Mild VOC: NA
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT % TOXICITY DATA
Reaction product of epichlorohydrin & bisphenol A 025085-99-8 65-85% See Ingredient Sheet 110104
1,4 Butanediol Diglycidyl Ether 2425-79-8 15-35% NA
Reaction product of epichlorohydrin & bisphenol A is considered hazardous under OSHA鈥檚 Hazardous
Communication Standards under 29CFR, 1910.1200. 1,4 butanediol diglycidyl ether is considered hazardous under
311 and 312 of Sara Title III.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >400F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS
was prepared. No warranty, guarantee, or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what measures are necessary to safely use this product, either
alone or in the combination with other products, and to determine its environmental regulatory compliance obligations
under applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK OM100, Part A
EFFECTS OF OVEREXPOSURE
INGESTION: Contains materials that may be moderately toxic. Ingestion can
upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: Skin irritation may be experienced with some individuals.
EYE CONTACT: Extremely irritating with the possibility of permanent eye injury.
CHRONIC/ACUTE EFFECTS OF EXPOSURE: Combinations of above conditions can
be experienced.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush well with water. Get medical attention
immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever high level
exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water
after handling. Solvents should not be used to clean skin because of increased penetration potential - protective skin
oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK OM100, Part B BILLERICA, MA 01821
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 03/07/2003
REV: A
* HMIS CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA
PERCENT VOLATILE: NA VAPOR PRESSURE: No Data
BOILING POINT: > 100掳C SOLUBILITY IN WATER: Slight
VAPOR DENSITY: NA EVAPORATION RATE: NA
APPEARANCE: Amber liquid SPECIFIC GRAVITY: 1.1
ODOR: Strong
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS # WT % TOXICITY DATA
Boron Trifluoride Amine Complex Trade Secret 75-100% NA
Boron Trifluoride Amine Complex requires reporting under OSHA鈥檚 Hazardous Communication Standards and also
Via Sara Title III, under section 312.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA
FLASH POINT: >250F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides
of nitrogen, carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
The information and recommendations contained in this MSDS have been compiled from sources believed to be
reliable and to represent the most reasonable current opinion on the subject when the MSDS was prepared. No
warranty, guarantee, or representation is made as to the correctness or sufficiency of the information. The user of
this product must decide what measures are necessary to safely use this product, either alone or in combination with
other products, and to determine its environmental regulatory compliance obligations under applicable federal or state
laws.
V. HEALTH HAZARD DATA Epo Tek OM100, Part B
EFFECTS OF OVEREXPOSURE
INGESTION: Contains materials that may be moderately toxic. Ingestion can
severely upset the gastric system.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: Corrosive; expected to cause severe skin damage with burns and
blistering.
EYE CONTACT: Extremely irritating with possible permanent eye injury.
CHRONIC/ACUTE EFFECTS OF EXPOSURE: Combinations of above conditions can
be experienced.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: In case of eye contact, flush well with water. Get medical attention
immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever high level
exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and water
after handling. Solvents should not be used to clean skin because of increased penetration potential - protective skin
oils can be dissolved by solvents.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK OM100 Tel: (978) 667-3805
DATE REVISED: 6/12/01
REV: A
SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None
1. TSCA Inventory Status
All the components of this product are listed on the TSCA Inventory.
2. RCRA Status
This product contains the following chemicals listed on the 40 CFR Part 261.33: None
3. CERCLA Status
This product contains the following chemicals listed on the 40 CFR Part 302.4: None
4. Transportation
Part A
Not Restricted
Part B
Not Restricted
_____________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.
INGREDIENT SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
EMERGENCY PHONE:
INGREDIENT CODE NUMBER: 110104 US/CANADA: 800-255-3924
INT鈥橪 COLLECT: + 813-248-0585
*HMIS: HEALTH (1) FLAMMIBILITY (1) DATE REVISED: 10/13/00
REACTIVITY (0) REV: A
CARCINOGEN: NTP (No) IARC (No) OSHA (No)
*HMIS CODE rating are estimated by Epoxy Technology
I. IDENTIFICATION & PHYSICAL DATA
Color: Colorless to slight Yellow
Odor: Slight
Physical State: Liquid
Solubility in Water: None
Vapor Pressure: NA
Specific Gravity: 1.16
Boiling Point: NA
II. HAZARDOUS INGREDIENTS WT % CAS #
Reaction product of epichlorohydrin & bisphenol A 100% 025085-99-8
TOXICITY DATA
Skin(LD50): in rabbits is 20,000mg/kg.
Ingestion(LD50): in rats is >5000mg/kg
Mutagenicity: Animal mutagenicity, studies were negative.
III. FIRE AND EXPLOSION DATA
FLASH POINT: 485 F
EXTINGUISHING MEDIA: Foam, CO2, dry chemical.
UNUSUAL FIRE AND EXPLOSION HAZARDS: None Known
FIRE FIGHTING EQUIPMENT: Wear positive pressure self-contained breathing apparatus and full protective
equipment.
IV. REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Avoid storage at high temperatures.
HAZARDOUS DECOMPOSITION PRODUCTS: None Known.
HAZARDOUS POLYMERIZATION: Will not occur
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to represent current opinion on the subject when the MSDS was prepared. No warranty, guarantee
or representation is made as to the correctness or sufficiency of the information. The user of this product must decide
what safety measures are necessary to safely use this product, whether alone or in combination with other products,
and determine its environmental regulatory compliance obligations under applicable federal or state laws.
V. HEALTH HAZARD DATA 110104
EFFECTS OF OVER EXPOSURE
None Established.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT: Flush eyes with plenty of water.
SKIN CONTACT: Wash off in flowing water or shower.
INGESTION: No adverse effects anticipated by this route of exposure incidental to proper
industrial handling.
INHALATION: No adverse effects anticipated by this route of exposure.
VI. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Soak up in absorbent material such as
sand, or polypropylene or polyethylene fiber products and collect in suitable containers. Residual
resin may be removed using steam or hot soapy water.
WASTE DISPOSAL METHOD: Employ waste disposal procedures that are in accordance with
federal, state and local regulations.
VII. SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Wear an approved respirator whenever exposure to air born
vapors is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves-neoprene or equivalent. A combination of barrier
cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a face shield
and impervious apron. A safety shower and eye wash facility should be available.
____________________________________________________________________________________________
VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors generated by heating.
Keep containers closed when not in use. Remove all contaminated clothing and wash.
|