Search   
MSDS 
:
 Benzylamine, 99%
CAS 
:
 100-46-9
SYNONYMS 
:
 Benzenemethanamine; (Phenylmethyl)amine; alpha-Aminotoluene;     Monobenzylamine.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 100-46-9 |Benzylamine | 99 | 202-854-1 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 21/22 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Harmful in contact with skin and if swallowed. Causes
burns.Corrosive.Lachrymator (substance which increases the flow of
tears).The toxicological properties of this material have not been
fully investigated.

Potential Health Effects
Eye:
Causes eye burns. Lachrymator (substance which increases the flow
of tears).
Skin:
Harmful if absorbed through the skin. Causes skin burns.
Ingestion:
Harmful if swallowed. Causes gastrointestinal tract burns. May cause
severe gastrointestinal tract irritation with nausea, vomiting and
possible burns. The toxicological properties of this substance have
not been fully investigated.
Inhalation:
Causes chemical burns to the respiratory tract. The toxicological
properties of this substance have not been fully investigated.
Inhalation of vapors causes irritation of the mucous membranes.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
In case of contact, immediately flush eyes with plenty of water for
at least 15 minutes. Get medical aid immediately.
Skin:
In case of contact, immediately flush skin with plenty of water for
at least 15 minutes while removing contaminated clothing and shoes.
Get medical aid immediately. Wash clothing before reuse.
Ingestion:
If swallowed, do NOT induce vomiting. Get medical aid immediately.
If victim is fully conscious, give a cupful of water. Never give
anything by mouth to an unconscious person.
Inhalation:
If inhaled, remove to fresh air. If not breathing, give artificial
respiration. If breathing is difficult, give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.
Antidote:
None reported.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Use water
spray to keep fire-exposed containers cool. Contact with metals may
evolve flammable hydrogen gas. Combustible liquid and vapor. Vapors
are heavier than air and may travel to a source of ignition and flash
back. Vapors can spread along the ground and collect in low or
confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, or water spray.
For large fires, use dry chemical, carbon dioxide, alcohol-resistant
foam, or water spray. Cool containers with flooding quantities of
water until well after fire is out.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Provide ventilation. A vapor suppressing foam
may be used to reduce vapors.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Wash hands before eating. Remove
contaminated clothing and wash before reuse. Use only in a
well-ventilated area. Do not get in eyes, on skin, or on clothing.
Empty containers retain product residue, (liquid and/or vapor), and
can be dangerous. Keep container tightly closed. Keep away from heat,
sparks and flame. Do not ingest or inhale. Discard contaminated
shoes. Do not pressurize, cut, weld, braze, solder, drill, grind, or
expose empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Keep container closed when not in use. Store in a tightly
closed container. Store in a cool, dry, well-ventilated area away
from incompatible substances.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Personal Protective Equipment

Eyes:
Wear chemical goggles and face shield.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant a respirator's use. Follow the
OSHA respirator regulations found in 29 CFR 1910.134
or European Standard EN 149. Always use a NIOSH or
European Standard EN 149 approved respirator when
necessary.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: clear slightly yellow
Odor: ammonia-like
pH: Strongly alkaline
Vapor Pressure: 133 mbar @ 120
Viscosity: Not available.
Boiling Point: 182-185 deg C
Freezing/Melting Point: 10 deg C
Autoignition Temperature: 390 deg C ( 734.00 deg F)
Flash Point: 72 deg C ( 161.60 deg F)
Explosion Limits, lower: 0.70
Explosion Limits, upper: 8.20
Decomposition Temperature: Not available.
Solubility in water: Slightly soluble.
Specific Gravity/Density: 0.98
Molecular Formula: C7H9N
Molecular Weight: 107.15

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures. Absorbs carbon
dioxide from the air.
Conditions to Avoid:
High temperatures, mechanical shock, ignition sources, excess heat,
temperatures above 65C, plastics.
Incompatibilities with Other Materials:
Strong oxidizing agents, acids, anhydrides, isocyanates, acid
anhydrides, acid chlorides, aldehydes, N-chlorosuccinimide.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide.
Hazardous Polymerization: Will not occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 100-46-9: DP1488500
LD50/LC50:
Not available.
LD50- Lethal dose, 50 percent kill]
unspecified) = 700
Carcinogenicity:
Benzylamine -
Not listed by ACGIH, IARC, or NTP.
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****

Ecotoxicity:
Fish: Fathead Minnow: LC50 = 94.5-106 mg/L; 96 Hr.; Flow-through,
23.9 degrees C, pH 7.9Fish: Fathead Minnow: EC50 = 17-21.4 mg/L;
5,10,15 Minutes; Microtox test

**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.*
Hazard Class: 8
UN Number: 2735
Packing Group: II
IMO
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.
Hazard Class: 8
UN Number: 2735
Packing Group: II
RID/ADR
Shipping Name: AMINES, LIQUID, CORROSIVE, N.O.S.
Hazard Class: 8
UN Number: 2735
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 21/22 Harmful in contact with skin and if
swallowed.
R 34 Causes burns.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 100-46-9: 1
United Kingdom Occupational Exposure Limits

United Kingdom Maximum Exposure Limits

Canada
CAS# 100-46-9 is listed on Canada's DSL List.
CAS# 100-46-9 is not listed on Canada's Ingredient Disclosure List.
Exposure Limits
US FEDERAL
TSCA
CAS# 100-46-9 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 4/30/1999 Revision #5 Date: 10/05/2004

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Zincon, monosodium salt 62625-22-3
Propylamine, 98% 107-10-8
Phenylmercuric Acetate, 98.0-100.5% 62-38-4
Kaolin 1332-58-7
Triethyl orthoformate, 98% 122-51-0
n-Methylbenzylamine, 97% 103-67-3
Triphenylmethyl chloride 76-83-5
8-Hydroxy-1,3,6-Pyrenetrisulfonic Acid Trisodium Salt, 98% (UV-Vis) 6358-69-6
Trans-2-Aminocyclohexanol Hydrochloride, 99% 5456-63-3
Benzoin methyl ether, 96% (tlc) 3524-62-7
Heptanoic Acid, 98% 111-14-8
Diisobutylaluminum hydride(DIBAL-H), 1.0M solution in hexane 110-54-3
Diisobutylaluminum hydride (1.0M solution in toluene) 108-88-3
1-Phenyltridecane 123-02-4
Glycolic Acid, 99% 79-14-1
Phenylacetyl chloride, 98% 103-80-0
Rubidium Hydroxide, 99%, 50 wt% Solution In Water 1310-82-3
Adenosine 5'-Triphosphate, Disodium Salt Hydrate, 98%(HPLC) 987-65-5
TRICHLOROACETYL CHLORIDE, 99% 76-02-8
Silver Carbonate, 99% 534-16-7
Tetrabutylammonium Hydrogen Sulfate, 98% 32503-27-8
Adipoyl Chloride, 99+% (Titr.) 111-50-2
Benzylamine, 99% 100-46-9
1,3-Cyclopentanedione, 97% 3859-41-4
Poly(n-vinylcarbazole), secondary standard 25067-59-8
Nonanoic Acid, Tech., 90% 112-05-0
(D,L)-4-Fluoro-alpha-methylbenzylamine, 97% 403-40-7
Selenium(iv) oxide, p.a. 7446-08-4
Selenium(IV) oxide 7446-08-4
4'-Nitroacetanilide 104-04-1
Manganese(II) chloride, anhydrous 7773-01-5
Pinacolone, 96% (gc) 75-97-8
Cis-Dicyclohexano-18-Crown-6, Mixture of Syn-Cis and Anti-Cis 16069-36-6
cis-Dicyclohexano-18-crown-6, cis-anti-cis isomer, 98+% 15128-66-2
1-Nitroso-2-naphthol-3,6-disulfonic acid, disodium salt hydrate, 98% 525-05-3
2-Naphthol, 98% 135-19-3
2-Naphthol (techn) 135-19-3
3-Bromopropionic Acid, 97% 590-92-1
4'-Chloroacetophenone, 97% 99-91-2
Ethyl chloroformate, 99% 541-41-3
6-Chloro-1-Hexanol, 95% 2009-83-8
1,3-Cyclohexadiene, 96%, stabilized with 50 ppm BHT 592-57-4
N-(4-Chlorophenyl)-p-toluenesulfonamide, pract. 2903-34-6
Camphene, 80% 79-92-5
N,N'-Methylenebisacrylamide, 96% 110-26-9
3-Chlorobenzoic Acid, 99+% 535-80-8
3,5-Dimethylphenol, 98% 108-68-9
4-Chlorostyrene, stabilized with 0.1% tert-butylcatechol 98-29-3
Cyanogen Bromide, 97% 506-68-3
Tin, Powder, 99.9999% 7440-31-5

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net