**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 122-51-0 |Triethyl orthoformate | 98.0 | 204-550-4 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI F
Risk Phrases: 10 36/38
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Irritating to eyes and skin.
Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
May cause irritation of the digestive tract.
Inhalation:
May cause respiratory tract irritation. Vapors may cause dizziness
or suffocation.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. Use water
spray to keep fire-exposed containers cool. Flammable liquid and
vapor. Vapors may be heavier than air. They can spread along the
ground and collect in low or confined areas. Containers may explode
when heated.
Extinguishing Media:
Use water spray to cool fire-exposed containers. This material is
lighter than water and insoluble in water. The fire could easily be
spread by the use of water in an area where the water cannot be
contained. Do NOT use straight streams of water. For small fires,
use dry chemical, carbon dioxide, water spray or regular foam. Cool
containers with flooding quantities of water until well after fire
is out. For large fires, use water spray, fog or regular foam.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Remove all sources of ignition. A
vapor suppressing foam may be used to reduce vapors. Water spray may
reduce vapor but may not prevent ignition in closed spaces.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use with adequate ventilation.
Ground and bond containers when transferring material. Avoid contact
with eyes, skin, and clothing. Empty containers retain product
residue, (liquid and/or vapor), and can be dangerous. Keep container
tightly closed. Keep away from heat, sparks and flame. Avoid
ingestion and inhalation. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose empty containers to heat, sparks or
open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate general or local exhaust ventilation to keep airborne
concentrations below the permissible exposure limits.
Exposure Limits
CAS# 122-51-0:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: Clear
Odor: pungent odor
pH: Not available.
Vapor Pressure: 10 mm Hg @40.5C
Viscosity: Not available.
Boiling Point: 146 deg C @ 760.00mm Hg
Freezing/Melting Point: 30 deg C
Autoignition Temperature: 180 deg C ( 356.00 deg F)
Flash Point: 30 deg C ( 86.00 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: 1.35 g/l in water (decomposes)
Specific Gravity/Density: .8910g/cm3
Molecular Formula: C7H16O3
Molecular Weight: 148.20
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, strong oxidants.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 122-51-0: RM6475000
LD50/LC50:
CAS# 122-51-0: Dermal, guinea pig: LD50 = >10 mL/kg; Draize test,
rabbit, eye: 100 mg/24H Moderate; Draize test, rabbit, skin: 500
mg/24H Mild; Oral, rat: LD50 = 7060 mg/kg; Skin, rabbit: LD50 = 20
mL/kg.
Carcinogenicity:
Triethyl orthoformate -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: ETHYL ORTHOFORMATE
Hazard Class: 3
UN Number: 2524
Packing Group: III
IMO
Shipping Name: ETHYL ORTHOFORMATE
Hazard Class: 3.3
UN Number: 2524
Packing Group: III
RID/ADR
Shipping Name: ETHYL ORTHOFORMATE
Hazard Class: 3
UN Number: 2524
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI F
Risk Phrases:
R 10 Flammable.
R 36/38 Irritating to eyes and skin.
Safety Phrases:
S 16 Keep away from sources of ignition - No
smoking.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 37/39 Wear suitable gloves and eye/face
protection.
WGK (Water Danger/Protection)
CAS# 122-51-0: 1
Canada
CAS# 122-51-0 is listed on Canada's DSL List.
CAS# 122-51-0 is listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 122-51-0 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 10/24/1997 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Zincon, monosodium salt
| 62625-22-3 |
|
Propylamine, 98%
| 107-10-8 |
|
Phenylmercuric Acetate, 98.0-100.5%
| 62-38-4 |
|
Kaolin
| 1332-58-7 |
|
Triethyl orthoformate, 98%
| 122-51-0 |
|
n-Methylbenzylamine, 97%
| 103-67-3 |
|
Triphenylmethyl chloride
| 76-83-5 |
|
8-Hydroxy-1,3,6-Pyrenetrisulfonic Acid Trisodium Salt, 98% (UV-Vis)
| 6358-69-6 |
|
Trans-2-Aminocyclohexanol Hydrochloride, 99%
| 5456-63-3 |
|
Benzoin methyl ether, 96% (tlc)
| 3524-62-7 |
|
Heptanoic Acid, 98%
| 111-14-8 |
|
Diisobutylaluminum hydride(DIBAL-H), 1.0M solution in hexane
| 110-54-3 |
|
Diisobutylaluminum hydride (1.0M solution in toluene)
| 108-88-3 |
|
1-Phenyltridecane
| 123-02-4 |
|
Glycolic Acid, 99%
| 79-14-1 |
|
Phenylacetyl chloride, 98%
| 103-80-0 |
|
Rubidium Hydroxide, 99%, 50 wt% Solution In Water
| 1310-82-3 |
|
Adenosine 5'-Triphosphate, Disodium Salt Hydrate, 98%(HPLC)
| 987-65-5 |
|
TRICHLOROACETYL CHLORIDE, 99%
| 76-02-8 |
|
Silver Carbonate, 99%
| 534-16-7 |
|
Tetrabutylammonium Hydrogen Sulfate, 98%
| 32503-27-8 |
|
Adipoyl Chloride, 99+% (Titr.)
| 111-50-2 |
|
Benzylamine, 99%
| 100-46-9 |
|
1,3-Cyclopentanedione, 97%
| 3859-41-4 |
|
Poly(n-vinylcarbazole), secondary standard
| 25067-59-8 |
|
Nonanoic Acid, Tech., 90%
| 112-05-0 |
|
(D,L)-4-Fluoro-alpha-methylbenzylamine, 97%
| 403-40-7 |
|
Selenium(iv) oxide, p.a.
| 7446-08-4 |
|
Selenium(IV) oxide
| 7446-08-4 |
|
4'-Nitroacetanilide
| 104-04-1 |
|
Manganese(II) chloride, anhydrous
| 7773-01-5 |
|
Pinacolone, 96% (gc)
| 75-97-8 |
|
Cis-Dicyclohexano-18-Crown-6, Mixture of Syn-Cis and Anti-Cis
| 16069-36-6 |
|
cis-Dicyclohexano-18-crown-6, cis-anti-cis isomer, 98+%
| 15128-66-2 |
|
1-Nitroso-2-naphthol-3,6-disulfonic acid, disodium salt hydrate, 98%
| 525-05-3 |
|
2-Naphthol, 98%
| 135-19-3 |
|
2-Naphthol (techn)
| 135-19-3 |
|
3-Bromopropionic Acid, 97%
| 590-92-1 |
|
4'-Chloroacetophenone, 97%
| 99-91-2 |
|
Ethyl chloroformate, 99%
| 541-41-3 |
|
6-Chloro-1-Hexanol, 95%
| 2009-83-8 |
|
1,3-Cyclohexadiene, 96%, stabilized with 50 ppm BHT
| 592-57-4 |
|
N-(4-Chlorophenyl)-p-toluenesulfonamide, pract.
| 2903-34-6 |
|
Camphene, 80%
| 79-92-5 |
|
N,N'-Methylenebisacrylamide, 96%
| 110-26-9 |
|
3-Chlorobenzoic Acid, 99+%
| 535-80-8 |
|
3,5-Dimethylphenol, 98%
| 108-68-9 |
|
4-Chlorostyrene, stabilized with 0.1% tert-butylcatechol
| 98-29-3 |
|
Cyanogen Bromide, 97%
| 506-68-3 |
|
Tin, Powder, 99.9999%
| 7440-31-5 |
|
|