**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 111-50-2 |Adipoyl chloride | 99 % | 203-876-4 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 14 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Reacts violently with water. Causes burns.Corrosive.Water-Reactive.
Potential Health Effects
Eye:
Causes eye burns. When substance becomes wet or comes in contact
with moisture of the mucous membranes, it will cause irritation. May
cause chemical conjunctivitis and corneal damage.
Skin:
Causes skin burns. Contact with skin causes irritation and possible
burns, especially if the skin is wet or moist. May cause irritation
and dermatitis. May cause cyanosis of the extremities. May cause
skin rash (in milder cases), and cold and clammy skin with cyanosis
or pale color.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns. May cause perforation of the digestive
tract. May cause systemic effects.
Inhalation:
Causes chemical burns to the respiratory tract. Inhalation may be
fatal as a result of spasm, inflammation, edema of the larynx and
bronchi, chemical pneumonitis and pulmonary edema. Aspiration may
lead to pulmonary edema. May cause systemic effects. Inhalation at
high concentrations may cause CNS depression and asphixiation.
Chronic:
Effects may be delayed.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Get medical aid immediately. Do NOT allow victim to rub or keep eyes
closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
soap and water for at least 15 minutes while removing contaminated
clothing and shoes. Wash clothing before reuse. Destroy contaminated
shoes. If water-reactive products are embedded in the skin, no water
should be applied. The embedded products should be covered with a
light oil.
Ingestion:
Do NOT induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure to fresh air
immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation. If breathing has ceased apply artificial respiration
using oxygen and a suitable mechanical device such as a bag and a
mask.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Water
Reactive. Material will react with water and may release a flammable
and/or toxic gas. Use water spray to keep fire-exposed containers
cool. Combustible Liquid. May ignite or explode on contact with
steam or moist air. Containers may explode when heated. Containers
may explode when heated or if contaminated with water.
Extinguishing Media:
Use dry sand or earth to smother fire. Do NOT use water directly on
fire. Use foam, dry chemical, or carbon dioxide. DO NOT USE WATER!
Do NOT get water inside containers. Contact professional
fire-fighters immediately. Cool containers with flooding quantities
of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. Do
not expose spill to water. Do not get water inside containers.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Wash hands before eating. Use only
in a well-ventilated area. Do not allow water to get into the
container because of violent reaction. Do not breathe dust, vapor,
mist, or gas. Do not get in eyes, on skin, or on clothing. Empty
containers retain product residue, (liquid and/or vapor), and can be
dangerous. Keep container tightly closed. Avoid contact with heat,
sparks and flame. Do not allow contact with water. Discard
contaminated shoes. Do not pressurize, cut, weld, braze, solder,
drill, grind, or expose empty containers to heat, sparks or open
flames. Keep from contact with moist air and steam.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances. Corrosives
area. Do not get water inside containers.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use explosion-proof ventilation equipment. Facilities storing or
utilizing this material should be equipped with an eyewash facility
and a safety shower. Use adequate general or local exhaust
ventilation to keep airborne concentrations below the permissible
exposure limits.
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR ??1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant a respirator's use.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Appearance: colorless to yellow
Odor: Pungent odor.
pH: Not available.
Vapor Pressure: 2 mm Hg @ 20 C
Viscosity: Not available.
Boiling Point: 105.0 - 107.0 deg C @ 2.00mm
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 72 deg C ( 161.60 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Reacts.
Specific Gravity/Density: 1.2600g/cm3
Molecular Formula: C6H8Cl2O2
Molecular Weight: 183.03
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures. Combines vigorously
or explosively with water.
Conditions to Avoid:
Incompatible materials, ignition sources, contact with water, excess
heat, exposure to moist air or water.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, phosgene, carbon monoxide, irritating and toxic
fumes and gases, carbon dioxide.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 111-50-2 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Adipoyl chloride -
Not listed by ACGIH, IARC, NIOSH, NTP, or OSHA.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: CORROSIVE LIQUID, NOS
Hazard Class: 8
UN Number: 1760
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, NOS
Hazard Class: 8
UN Number: 1760
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, NOS
Dangerous Goods Code: 8(36B)
UN Number: 1760
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 14 Reacts violently with water.
R 34 Causes burns.
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 111-50-2: No information available.
United Kingdom Occupational Exposure Limits
Canada
CAS# 111-50-2 is listed on Canada's DSL List.
CAS# 111-50-2 is not listed on Canada's Ingredient Disclosure List.
Exposure Limits
US FEDERAL
TSCA
CAS# 111-50-2 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 12/12/1997 Revision #7 Date: 8/02/2000
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Zincon, monosodium salt
| 62625-22-3 |
|
Propylamine, 98%
| 107-10-8 |
|
Phenylmercuric Acetate, 98.0-100.5%
| 62-38-4 |
|
Kaolin
| 1332-58-7 |
|
Triethyl orthoformate, 98%
| 122-51-0 |
|
n-Methylbenzylamine, 97%
| 103-67-3 |
|
Triphenylmethyl chloride
| 76-83-5 |
|
8-Hydroxy-1,3,6-Pyrenetrisulfonic Acid Trisodium Salt, 98% (UV-Vis)
| 6358-69-6 |
|
Trans-2-Aminocyclohexanol Hydrochloride, 99%
| 5456-63-3 |
|
Benzoin methyl ether, 96% (tlc)
| 3524-62-7 |
|
Heptanoic Acid, 98%
| 111-14-8 |
|
Diisobutylaluminum hydride(DIBAL-H), 1.0M solution in hexane
| 110-54-3 |
|
Diisobutylaluminum hydride (1.0M solution in toluene)
| 108-88-3 |
|
1-Phenyltridecane
| 123-02-4 |
|
Glycolic Acid, 99%
| 79-14-1 |
|
Phenylacetyl chloride, 98%
| 103-80-0 |
|
Rubidium Hydroxide, 99%, 50 wt% Solution In Water
| 1310-82-3 |
|
Adenosine 5'-Triphosphate, Disodium Salt Hydrate, 98%(HPLC)
| 987-65-5 |
|
TRICHLOROACETYL CHLORIDE, 99%
| 76-02-8 |
|
Silver Carbonate, 99%
| 534-16-7 |
|
Tetrabutylammonium Hydrogen Sulfate, 98%
| 32503-27-8 |
|
Adipoyl Chloride, 99+% (Titr.)
| 111-50-2 |
|
Benzylamine, 99%
| 100-46-9 |
|
1,3-Cyclopentanedione, 97%
| 3859-41-4 |
|
Poly(n-vinylcarbazole), secondary standard
| 25067-59-8 |
|
Nonanoic Acid, Tech., 90%
| 112-05-0 |
|
(D,L)-4-Fluoro-alpha-methylbenzylamine, 97%
| 403-40-7 |
|
Selenium(iv) oxide, p.a.
| 7446-08-4 |
|
Selenium(IV) oxide
| 7446-08-4 |
|
4'-Nitroacetanilide
| 104-04-1 |
|
Manganese(II) chloride, anhydrous
| 7773-01-5 |
|
Pinacolone, 96% (gc)
| 75-97-8 |
|
Cis-Dicyclohexano-18-Crown-6, Mixture of Syn-Cis and Anti-Cis
| 16069-36-6 |
|
cis-Dicyclohexano-18-crown-6, cis-anti-cis isomer, 98+%
| 15128-66-2 |
|
1-Nitroso-2-naphthol-3,6-disulfonic acid, disodium salt hydrate, 98%
| 525-05-3 |
|
2-Naphthol, 98%
| 135-19-3 |
|
2-Naphthol (techn)
| 135-19-3 |
|
3-Bromopropionic Acid, 97%
| 590-92-1 |
|
4'-Chloroacetophenone, 97%
| 99-91-2 |
|
Ethyl chloroformate, 99%
| 541-41-3 |
|
6-Chloro-1-Hexanol, 95%
| 2009-83-8 |
|
1,3-Cyclohexadiene, 96%, stabilized with 50 ppm BHT
| 592-57-4 |
|
N-(4-Chlorophenyl)-p-toluenesulfonamide, pract.
| 2903-34-6 |
|
Camphene, 80%
| 79-92-5 |
|
N,N'-Methylenebisacrylamide, 96%
| 110-26-9 |
|
3-Chlorobenzoic Acid, 99+%
| 535-80-8 |
|
3,5-Dimethylphenol, 98%
| 108-68-9 |
|
4-Chlorostyrene, stabilized with 0.1% tert-butylcatechol
| 98-29-3 |
|
Cyanogen Bromide, 97%
| 506-68-3 |
|
Tin, Powder, 99.9999%
| 7440-31-5 |
|
|