MATERIAL SAFETY DATA SHEET
PRODUCT NAME: CP-37A DATE PREPARED: April 14, 1999
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Identifier: CP-37A General Use: Coating and Adhesive
Product Description: Solvent Based Elastomeric Material
MANUFACTURER: EMERGENCY TELEPHONE NUMBERS:
Childers Products Co. Health (215) 943-7600 8 am-5 pm EST M-F
34799 Curtis Blvd. Transportation (215) 943-7600 8 am-5 pm EST M-F
Eastlake, Ohio USA 44095 CHEM-TEL (800)255-3924 24 hours Everyday
2. COMPOSITION/INFORMATION ON INGREDIENTS
OSHA HAZARDOUS COMPONENTS (29 CFR 1910.1200):
INGREDIENT CAS EXPOSURE LIMITS
NUMBER PERCENT OSHA PEL / ACGIH TLV
(ppm) (mg/m3)
Aromatic Hydrocarbon 1330-20-7 0-13 100/100 435 /435
Aromatic Hydrocarbon 108-88-3 0-16 100/100 525/525
Aliphatic Hydrocarbon NA 16-32 5/5
Silicone Dioxide 14808-60-7 0-8 0.1/0.1
Hydrated Alumina NA 0-16 10/10
p-Quinone Dioxime 105-11-3 0-8 ND
Metal Oxide NA 0-8 0.5/0.5
Brominated Compound NA 0-8 ND
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM鈥橲 RATING
Health 3
Flammability 3
VOC CONTENT Reactivity 1
CP 37A 2.34 lbs/gl (281 g/l) Protection H
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW: Harmful if inhaled. May affect the brain or nervous system causing dizziness, headache, or nausea.
POTENTIAL HEALTH EFFECTS:
INHALATION: May cause lung injury. Can be irritating, may cause nasal irritation, dizziness, weakness and fatigue., nausea, or headache.
Extreme overexposure can lead to unconsciousness and even asphyxiation.
EYE CONTACT: Moderately irritating. Can cause corneal damage. SKIN CONTACT:Causes skin burns. May be absorbed through skin.
INGESTION: Ingestion could result in irritation, burns, and some corrosive action in the mouth, stomach tissue, and digestive tract.
CHRONIC: Repeated excessive exposures to this product may cause: central nervous system, liver and/or kidney effects and respiratory and
eye irritation. Overexposure to this material (or its components) has been suggested to cause liver abnormalities in humans. Some individuals
may be hypersensitive to this material.
4. FIRST AID MEASURES
INHALATION: If breathing difficulties, dizziness, or lightheadedness occur when working in areas with high vapor concentrations
victim should seek air free of vapors. If victim experiences continued breathing difficulties, administer oxygen until medical assistance
can be rendered. If breathing stops, begin artificial respiration and seek immediate medical attention.
EYE CONTACT: Flush thoroughly with water for at least 15 minutes. Consult a physician if irritation persists.
SKIN CONTACT: Remove contaminated clothing and shoes. Wash thoroughly with soap and water.
INGESTION: If this product is swallowed, DO NOT induce vomiting. If patient is conscious, give several cups of water or milk and transport to
a medical facility.
5. FIRE FIGHTING MEASURES
FLASHPOINT: 45F 7C FLAMMABLE LIMITS: 1%-ND AUTOIGNITION TEMPERATURE: Not Established.
GENERAL HAZARD: The vapors from these products can be ignited by open flames, welding operations, sparks, or any other
source of ignition.
FIRE FIGHTING INSTRUCTIONS: Use Foam, CO2, or dry chemical. Water may be used to keep adjacent containers cool. Avoid
spreading burning liquid with water used for cooling.
FIRE FIGHTING EQUIPMENT: The use of self-contained breathing apparatus is recommended for fire fighters.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide and/or carbon monoxide and other toxic gases.
6. ACCIDENTAL RELEASE MEASURES
LAND SPILL: Keep away from heat, sparks, open flames, or any other ignition sources. Vapor is heavier than air. Vapors may cause
flash fires. Avoid contact with skin and breathing of vapors. Ventilate area. Scrape material into containers using non sparking tools.
WATER SPILL: Product is heavier than water and is insoluble. Solvents that leach out of the product will float. Keep heat, sparks,
open flames, or any other ignition sources away from the water. Use absorbent pads to collect any solvent. Dike any flowing water.
Absorb solvent behind the dike.
7. HANDLING AND STORAGE
GENERAL: Keep container tightly closed. Loosen closure cautiously before opening. Store in a dry, ventilated area. Protect from
static discharge. Keep away from open flames, sparks, and all other ignition sources. Follow all MSDS/label warnings even after
container is emptied.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS: Maintain positive ventilation. Do not suck vapor laden air through non explosion proof fans or
equipment.
PERSONAL PROTECTION:
RESPIRATOR: RESPIRATORS ARE TO BE USED BY PROPERLY TRAINED PERSONNEL ONLY.
Use with adequate ventilation. Do not breathe vapors or spray mist. Wear an appropriate, properly fitted respirator (NIOSH/MSHA
approved) during and after application unless air monitoring demonstrates vapor/mist levels are below applicable limits. Follow
respirator manufacturer鈥檚 directions for respirator use.
PROTECTIVE CLOTHING: Safety glasses, chemical goggles and/or face shields are recommended. Wear impermeable gloves.
Impermeable aprons are recommended.
9. PHYSICAL AND CHEMICAL PROPERTIES
Vapor Pressure: Not established Boiling Point: 230F/110C Freezing Point: Not established Specific Gravity: 1.2
Vapor Density: Heavier than air Viscosity: Thick liquid Appearance: Pigmented liquid Odor: Naptha like odor
Solubility in Water: Negligible Evaporation Rate: Not established pH: Not applicable Physical State: paste
10. STABILITY AND REACTIVITY
GENERAL: This product is stable and hazardous polymerization will not occur.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: This product is incompatible with oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide and/or carbon dioxide.
11. TOXICOLOGICAL INFORMATION: No data is available on the product itself.
CAS# 1330-20-7 has the following characteristics:
acute oral LD50 4.3G/KG (rat) acute inhalation LC50 6700PPM/4H(rat) acute dermal LD50>3.95ML/KG(rabbit)
CAS number 108-88-3 has the following characteristics:
acute oral LD50 5000mg/KG(rat) acute inhalation LC50 5320 ppm/ 8hr(mouse) acute dermal LD50 14 g/KG(rabbit)
12. ECOLOGICAL INFORMATION: No data available.
13. DISPOSAL CONSIDERATIONS
RCRA Hazard Class: D001 Consult with disposal company. Ensure disposal is in compliance with government requirements
and ensure conformity to local disposal regulations.
14. TRANSPORT INFORMATION
DOT (United States Department of Transportation): CANADIAN TDG (Transportation of Dangerous Goods):
PROPER SHIPPING NAME: Coating Solution FLAMMABILITY CLASSIFICATION: 3.2
HAZARD CLASS:3.2
IDENTIFICATION NUMBER:UN1139
15. REGULATORY INFORMATION
TSCA (Toxic Substance Control Act): All components of this product are listed on the TSCA Inventory.
CERCLA (Comprehensive Response Compensation, and Liability Act):RQ for 1330-20-7 is 100 pounds.
RQ for 108-88-3 is 1000 pounds
Contact local authorities to determine if there may be other local reporting requirements.
SARA TITLE III (Superfund Amendments and Reauthorization Act):
311/312 HAZARD CATAGORIES: Immediate Health, Delayed Health, Fire
313 REPORTABLE INGREDIENTS: 1330-20-7, 108-88-3
WARNING: This product contains a chemical(s) known to the State of California to cause cancer.
16. OTHER INFORMATION: REVISION SUMMARY: Supersedes August 10, 1998
THE INFORMATION RELATES TO THIS SPECIFIC MATERIAL. IT MAY NOT BE VALID FOR THIS MATERIAL IF USED IN
COMBINATION WITH ANY OTHER MATERIALS OR IN ANY PROCESS. IT IS THE USER鈥橲 RESPONSIBILITY TO SATISFY
ONESELF AS TO THE SUITABILITY AND COMPLETENESS OF THIS INFORMATION FOR HIS OWN PARTICULAR USE.
CP-37A
|