Material
CPS Coatings, Inc. Safety
Data
Sheet
SUPPLIER NOTIFICATION
UNDER SECTION 313 OF SARA
Pursuant to Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR 372, our product,
AS-5599 RAPID LINER URETHANE BEDLINER CATALYST (Part B), contains toxic chemicals in quantities
subject to the reporting requirements under Section 313 (See below).
Effective January 1, 1989 any persons who sells or otherwise distributes a mixture of trade name product containing toxic chemicals
must provide written notice to the recipient with the first shipment in each calendar year. If the recipient repackages or otherwise
redistributes this product, a notice indicating that this product is subject to the reporting requirements of Section 313, including the
reporting chemical name/category, CAS number and percent by weight, must accompany the shipment. Please note that the
Notification letter must be attached and remain attached to the Material Safety Data Sheet.
Contains: CAS Number Percent by Weight
Homopolymer of Hexamethylene Diisocyanate 28182-81-2 40%
Hexamethylene -1, 6-Diisocyanate 822-06-0 <0.6%
Toluene 108-88-3 44%
Xylene 1330-20-7 6%
If you have any questions regarding the notification requirement or any of the above
mentioned information, please do not hesitate to contact us at 318-222-6100.
Sincerely,
CPS Coatings
AS 5599-Not Leaded pg.1/4
Material Safety Data Sheet
SECTION I - MANUFACTURERS INFORMATION
PRODUCT NAME: AS-5599 RAPID LINER URETHANE BEDLINER CATALYST (Part B)
MSDS PREPARATION DATE: 7-30-2007
MANUFACTURER: CPS COATINGS, INC.
624 AIRPORT DR. SHREVEPORT, LA 71107
PRODUCT INFORMATION / EMERGENCY TELEPHONE: (318) 222-6100 / 1-800-424-9300
While CPS believes that the data herein is accurate & derived from quality sources, this data is not to be taken as a warrantee or
product liability. It is offered solely for your consideration and personal protection.
SECTION II - HAZARDOUS INGREDIENTS
Ingredient CAS Number ACGIH TLV OSHA PEL ppm SARA Title, Sec 313
Homopolymer of Hexamethylene 28182-81-2 .5 mg/M3 .5mg/M3 N
Diisocyanate
Hexamethylene -1, 6-Diisocyanate 822-06-0 .005 IWA N/E N
Toluene 108-88-3 100 100 Y
Xylene 1330-20-7 100 100 Y
SECTION III - PHYSICAL DATA
Boiling Point: 280掳 F Vapor Pressure (mmHg): @68掳 F. 9.0
Vapor Density (Air=1): Heavier than air Melting Point (掳C): N/A
Specific Gravity: .92 Solubility in Water- Reacts slowly to liberate C02 Gas
Evaporation Rate: Slower than Ether Appearance and Odor: Clear- Mild
V O C 鈥? 1.15 lbs / per quart as Packaged
Mixed Product total = 2.97 lbs./gal.
SECTION IV - FIRE AND EXPLOSION DATA
Flash Point (Method Used): T.C.C.. 掳F. 45 Flammable Explosion: LEL = 1% UEL = 7%
Extinguishing Media: (1) Dry Chemical. (2) CO2. (3) Foam
Special Fire Fighting Procedures: Dry Chemical, Carbon Dioxide, Water Spray or Regular Foam. Full protective equipment
including self-contained breathing apparatus should be used. If water is used, fog nozzles are preferable. Water may be used to
cool closed containers to prevent pressure build-up due to extreme heat. Caution: A straight stream of water will spread fire.
Unusual Fire and Explosion Hazards: Vapor accumulation will flash and/or explode, if ignited. Containers may burst explosively if
overheated in fire. Cool with water spray or fog. Empty containers also present fire explosion hazard due to residual vapors. Keep
containers tightly closed. During emergency situations, over-exposure to decomposition products may cause a health hazard with no
symptoms immediately apparent. Obtain medical attention. SECTION V - HEALTH HAZARD DATA
AS 5599-Not Leaded pg.2/4
Material Safety Data Sheet
SECTION V - HEALTH HAZARD DATA
See attached Addendum for Lead products.
EFFECTS OF OVEREXPOSURE:
ACUTE: Inhalation - Anesthetic. Irritation or respiratory tract of acute nervous system depression. Overexposure may result in
headaches and nausea possibly followed by loss or consciousness. Ingestion Gastrointestinal irritation including vomiting can occur.
Aspiration of material into lungs may result in chemical pneumonitis which can be fatal. Skin contact may result in irritation and
absorption through Skin. Eye contact will irritate.
CHRONIC: Some reports have associated repeated. prolonged overexposure to solvents with permanent central nervous system
changes. Misuse by concentrating and inhaling the contents nay be harmful or fatal. See Target Organ Effect Sheet for further
information about effects of overexposure and medical conditions generally aggravated by exposure. The Target Organ Effects Sheet
is a integral part or this Material Safety Data Sheet; any duplication of the MSDS must include it.
SKIN CONTACT: Prolonged contact with the isocyanate can cause reddening, selling, rash, scaling or blistering. In those who have
developed a skin sensitization. These symptoms can develop as a result of contact with very small amounts of liquid material or even
as a result of vapor only exposure. Chronic skin exposure to solvents may cause effects similar to those identified under chronic
inhalation effects.
EXPOSURE LIMITS: The Mobay Guideline level of 0.5 mg/M3鈥? TWA and 1.0 mg/M3 鈥? STEL for Homopolymer of HID and 0.20
ppm ceiling for HDI monomer are internal guides based on limited data. They are provided as guides pending the review of future
data.
California Proposition 65 requires that warnings t>e given regarding exposures to chemicals listed by the State as being known to
cause cancer, birth defects of other reproductive harm. This product is not intentionally formulated with chemicals that are listed by
California as causing the above effects. However we are informed by the suppliers of some chemical ingredients used in this product
that they may contain trace, but detectable levels of some listed chemicals as impurities. Therefore trace, but detectable, levels or
listed chemicals nay be present in this product.
EMERGENCY & FIRST AID PROCEDURES:
Vapor Inhalation - Restore breathing. Remove to fresh air. Keep warm and quiet. Notify a physician.
Eye Contact - Flush IMMEDIATELY with copious amounts of running water for at least 15 minutes. Take to physician for
definitive medical treatment鈥?
Skin Contact - Clean and wash added area with water. Consult a physician.
Ingestion - DO NOT INDUCE VOMITING! Call physician Immediately!
TOXICITY: Slightly Toxic by ingestion.
SECTION VI - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID, Heat. open flames. electrical and static discharge.
INCOMPATIBILITY (materials to avoid). Strong acid, alkalis. and oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Unknown other than CO2 and possible CO and Carbon smoke.
HAZARDOUS POLYMERIZATION: Will not occur.
AS 5599-Not Leaded pg.3/4
Material Safety Data Sheet
SECTION VII - SPILL OR LEAK PROCEDURES
STEPS IF SPILLED: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapors, Confine
spill with inert absorbent and
clean up with spark-proof tools.
WASTE DISPOSAL- Dispose of in accordance with local, state, and Federal regulations. Land rill or incinerate in approved
facility by licensed contractor.
Do not incinerate in closed container.
SECTION VIll - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Use NIOSH/MSHA TC23C Chemical / Mechanical type filter system to remove a combination
of particles. Gas & vapors. Use an air supplied respirator if necessary.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV鈥檚 and PEL鈥檚 (Section II) below recommended
levels. and flammable limits in air (Section IV) below the level necessary to produce explosion of fire. General mechanical
ventilation should comply with OSHA 1910,94.
PROTECFIVE GLOVES. To prevent prolonged exposure, use rubber gloves. Solvents may be absorbed through the skin.
EYE PPOTECTION: Safety glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Prevent prolonged skin contact to contaminated clothing.
SECTION IX - SPECIAL PRECAUTIONS
HANDLING PRECAUTIONS; Do not store over 120鈥橣. Avoid spillage and/or the creation or airborne aluminum dust. When
storing large quantities, store in building designed and protected against flammable liquids. Use static lines when mixing and
transferring material. Do not allow material to free rag more than five (5) inches.
OTHER PRECAUTIONS: FOR INDUSTRIAL USE ONLY. 00 NOT TAKE INTERNALLY, IF INGESTED, DO NOT
INDUCE VOMITING. CONSULT A PHYSICIAN.
DO NOT FLAME CUT, WELD, OR BRAZE ON COATED MATERIAL WITHOUT NIOSA / MSHA TC23C RESPIRATOR
THE INFORMATION CONTAINED HEREIN IS BASED ON TECHNICAL DATA WHICH WE BEIJEVE TO BE
RELIABLE. HOWEVER, SINCE THE CONDITIONS UNDER WHICH THIS INFORMATION MAY SE APPLIED ARE
BEYONI) OUR CONTROL. WE CAN ASSUME NO LIABILITY FOR RESULTS OF ITS APPLICATION.
THIS INFORMATION SHOULD BE USED ONLY BY PERSONS HAVING SUFFICIENT TECHNICAL SKILL TO MAKE
INFORMED JUDGEMENTS REGARDING IT鈥橲 APPLICATION.
AS 5599-Not Leaded pg.4/4
|