TECH LINE COATINGS, INC.
26844 ADAMS AVE. MURRIETA, CA 92562 USA
Phone 951-304-0498
Fax 951-461-9658
www.techlinecoatings.com
MATERIAL SAFETY DATA SHEET
SECTION I
COMMON NAME (S): TIK, Titanium Colorguard
CHEMICAL NAME(S) AND SYNONYM(S): INDUSTRIAL COATING
CHEMICAL FAMILY: N/A
FORMULA: Complex Mixture
EMERGENCY PHONE: (Chemtrec) 1-800-424-9300
INFORMATION PHONE: 951-304-0498
DATE PREPARED: 8/22/2003
SECTION II
HAZARDOUS INGREDIENTS
COMPONENT CAS# CONCENTRATIONS
XYLENE 1330-20-7 >10%
ACGIH TLV: 100 PPM (TECHNICAL GRADE XYLENE CONTAINS 16-20% ETHYL BENZENE CAS# 100-
OSHA PEL: 100 PPM 41-4 AND IS SUBJECT TO REPORTING REQUIREMENTS SARA TITLE III )
ISOBUTYLALCOHOL 78-83-1 >10%
ACGIH TLV: 50 PPM
OSHA PEL: 500 PPM
ETHANOL 064-175 <1%
ACGIH TLV: .1000 PPM
OSHA PEL: .1900 PPM
Nickel Antimony Titanium Yellow Rutile 8007-18-9 <10%
As Regulated
Antimony and compounds (as Sb)
ACGIH TLV: .5 mg/m3
OSHA PEL: .5 mg/m3
Nickel metal and insoluble compounds (as Ni)
ACGIH TLV: .2 mg/m3
OSHA PEL: 1 mg/m3
This product is the result of high temperature calcination of the component substances. Due to its unique crystalline structure the properties of this finished
pigment do not necessarily reflect the properties of the component metals or oxides.
COPPER CHROMITE BLACK SPINEL 68186-91-7 <30%
Copper dusts and mists (as Cu)
OSHA PEL: 1 MG/M3
ACGIH TLV: 1 MG/M3
SARA TITLE 313: YES
FILLERS TRADE SECRET
(Specific ingredients are not listed. Full information is available to qualified medical personnel)
The metallic portion of the formula is made through the alloying of a variety of materials. The alloy does not have the
properties of the individual ingredients that make up the alloy. Certain hazardous components of the alloy are listed
Ingredient 0%
CAS # ACHIG OSHA ECC ECC ECC
TLV-TWA PEL-TWA Symbols R-phase
Chromium 7440-47-3 16-18 0.5 mg/m3 1 mg/m3 Ti,Xi 25,36/37/
38, 43
Nickel 7440-47-0 10-14 1 mg.m3 1 mg.m3 Carc.Cat1 45.10,25,
Silicon 7440-21-3 <1 10 mg/m3 10:5 mg/m3 F 10
Note: "Total dust" and "Respirable Fraction" OSHA PEL values are listed for Silicon. NOTE: The National Toxicology program lists nickel,
chromium and certain chromium compounds to be carcinogenic. This alloy does not contain any Hexavalent Chromium
NOTE: XYLENE IS CONSIDERED BY SOME AUTHORITIES TO BE CARCINOGEN
Page 1
SECTION III
PHYSICAL CHARACTERISTICS____________________________________
FLASH POINT: 79F
BOILING POINT: 172-355 F.
VAPOR DENSITY (AIR = 1): <1
VAPOR PRESSURE: NOT ESTABLISHED
MELTING POINT: NOT APPLICABLE
APPEARANCE AND ODOR: LIGHT GRAY COLORED LIQUID/SOLVENT SMELL
SOLUBILITY IN WATER: POOR
REACTIVITY IN WATER: NONE
VOC'S: 750 GRAMS/L
SECTION IV
FIRE AND EXPLOSION HAZARD DATA_____________________________
FLASH POINT: 79 F.
FLAMMABLE LIMITS:
LEL- NOT ESTABLISHED
UEL- NOT ESTABLISHED
DOT: FLAMMABLE LIQUID
EXTINGUISHING MEDIA: FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL
SPECIAL FIRE FIGHTING PROCEDURES: USE FULL PROTECTIVE EQUIPMENT, INCLUDING SELF CONTAINED BREATHING
APPARATUS
UNUSUAL FIRE AND EXPLOSION HAZARDS: DURING EMERGENCY CONDITIONS, OVEREXPOSURE TO DECOMPOSITION PRODUCTS
MAY CAUSE A HEALTH HAZARD. SYMPTOMS MAY NOT BE IMMEDIATELY APPARENT. OBTAIN MEDICAL ATTENTION
SECTION V
REACTIVITY DATA
STABILITY: STABLE
INCOMPATIBILITY (MATERIALS TO AVOID): CONTACT WITH STRONG OXIDIZING AGENTS, ACIDS OR BASES
HAZARDOUS DECOMPOSITION PRODUCTS: CARBON MONOXIDE AND UNIDENTIFIED ORGANICS MAY BE FORMED
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
CONDITIONS TO AVOID: NONE
SECTION VI
HEALTH HAZARD DATA__________________________________________________
ROUTES OF ENTRY:
INHALATION? YES
SKIN? YES
INGESTION? YES
TOXICITY (ACUTE AND CHRONIC)
Chronic (long term) exposure, in laboratory animals, to this material (or it's components) has been found to cause the following effects; anemia, liver
abnormalities, kidney, lung and spleen damage.
Chronic overexposure to xylene (CAS# 1330-20-7) has been suggested to cause cardiac abnormalities in humans.
HEALTH HAZARDS:
Eyes: severe irritation, redness, tearing and blurred vision
Skin: prolonged or repeated contact can cause moderate irritation, defatting and dermatitis
Inhalation: excessive inhalation of vapors can cause metallic taste and nasal ulceration and perforation and respiratory irritation, dizziness, headache,
possible unconsciousness, death
Aspiration of the material into the lungs can cause chemical pneumonitis, which can be fatal
Ingestion: can cause gastrointestinal irritation, nausea, vomiting, and diarrhea.
Copper dusts and mists are eye and mucous membrane irritants and skin sensitizers. Exposure may result in irritation and metal-fume fever, metallic taste,
discoloration of the skin and hair.
EMERGENCY AND FIRST AID:
EYES: IMMEDIATELY FLUSH WITH PLENTY OF WATER, CALL A PHYSICIAN
(FLUSH FOR AT LEAST 15 MIN., INCLUDING UNDER EYELIDS)
SKIN: WASH WITH WATER. REMOVE CONTAMINATED CLOTHING IF IRRITATION OCCURS GET MEDICAL ATTENTION
INHALATION: REMOVE INDIVIDUAL TO FRESH AIR. ADMINISTER OXYGEN IF BREATHING IS DIFFICULT. CALL A PHYSICIAN
INGESTION: CALL A PHYSICIAN IMMEDIATELY. ONLY INDUCE VOMITING AT THE INSTRUCTION OF A PHYSICIAN
Page 2
* INTENTIONAL MISUSE BY DELIBERATE CONCENTRATING AND INHALING THE CONTENTS MAY BE HARMFUL OR FATAL
SECTION VII
SPILL OR LEAK PROCEDURES___________________________________
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: CLEAN SPILL WITH ABSORBENT MATERIAL, ELIMINATE IGNITION
SOURCES, WEAR PROTECTIVE GLOVES, GOGGLES AND MASK
WASTE DISPOSAL METHOD: DISPOSAL SHOULD BE MADE IN ACCORD WITH FEDERAL, STATE AND LOCAL REGULATIONS.
OTHER PRECAUTIONS: CONTACT LENSES POSE A SPECIAL HAZARD; SOFT LENSES MAY ABSORB ALL LENSES CONCENTRATE IRRITANTS
SECTION VIII
SPECIAL PROTECTION / CONTROL MEASURES:____________________
RESPIRATORY PROTECTION: USE NIOSH APPROVED RESPIRATOR IF TWA/TLV LIMITS ARE EXCEEDED
VENTILATION:
LOCAL EXHAUST: USE TO MAINTAIN BELOW TWA LIMITS
MECHANICAL: USE NON-SPARKING EQUIPMENT
PROTECTIVE GLOVES: CHEMICAL RESISTANT
EYE PROTECTION: SAFETY GLASSES WITH SIDE SHIELDS OR GOGGLES
OTHER PROTECTIVE EQUIPMENT: WEAR PROTECTIVE CLOTHING, CHEMICAL RESISTANT OR OTHER PROTECTIVE OUTERWEAR, AVOID
CONTACT WITH SKIN OR EYES
WORK / HYGIENIC PRACTICES: WASH THOROUGHLY AFTER HANDLING PRODUCT AND BEFORE EATING, DRINKING OR SMOKING
SECTION IX
SPECIAL PRECAUTIONS___________________________________________
HANDLING AND STORAGE: STORE IN A COOL DRY PLACE, SUITABLE FOR OSHA CLASS 1 FLAMMABLE LIQUIDS
REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS:
THIS PRODUCT CONTAINS A TOXIC CHEMICAL OR CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF
SECTION 313 OF TITLE III OF THE SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT OF 1986 AND 40 CFR
372. SEE SECTION 2, LIST LEGEND 02.
OSHA STANDARD 29 CFR 1910.1200 REQUIRES THAT INFORMATION BE PROVIDED TO EMPLOYEES REGARDING
THE HAZARDS OF CHEMICALS BY MEANS OF A HAZARD COMMUNICATION PROGRAM INCLUDING LABELING,
MATERIAL SAFETY DATA SHEETS, TRAINING AND ACCESS TO WRITTEN RECORDS. WE REQUEST THAT YOU, AND
IT IS YOUR LEGAL DUTY TO, MAKE ALL INFORMATION IN THIS MATERIAL SAFETY DATA SHEET AVAILABLE TO
YOUR EMPLOYEES.
TO AID OUR CUSTOMERS IN COMPLYING WITH REGULATORY REQUIREMENTS, SARA TITLE III HAZARD
CATEGORIES FOR THIS PRODUCT ARE INDICATED BELOW. IF THE WORD 鈥淵ES鈥? APPEARS NEXT TO ANY
CATEGORY, THIS PRODUCT MAY BE REPORTABLE BY YOU UNDER THE REQUIREMENTS OF 40. CFR. 370. PLEASE
CONSULT THOSE REGULATIONS FOR DETAILS.
------------------------------------------------------------------------------------------------------------------
THIS INFORMATION IS FURNISHED WITHOUT WARRANTY, REPRESENTATION, INDUCEMENT OR LICENSE OF ANY KIND, EXCEPT THAT
IT IS ACCURATE TO THE BEST OF TECH LINE COATINGS, INC., KNOWLEDGE OR OBTAINED FROM SOURCES BELIEVED BY TECH LINE
COATINGS, INC. TO BE ACCURATE, AND TECH LINE COATINGS, INC., DOES NOT ASSUME ANY LEGAL RESPONSIBILITY FOR USE OR
RELIANCE UPON SAME. BEFORE USING ANY CHEMICAL, READ ITS LABEL, INSTRUCTIONS AND MATERIAL SAFETY DATA SHEET.
Page 3
|