MATERIAL SAFETY DATA SHEET
1 CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Trade Name INK TF/Z PRINTING MEDIUM HD
268
MSDS Number
- -0
CAS Number
TRANS TECH AMERICA, INC.
Supplier
475 N. GARY AVENUE
CAROL STREAM, IL 60188 USA
Telephone Numbers - 24 Hour Emergency Assistance
Emergency (352)323-3500
Telephone Numbers - General Assistance
Information (630)752-4000
2 COMPOSITION / INFORMATION ON INGREDIENTS
Concentration
Ingredient Name CAS Number Exposure Limits / Health Hazards
NO HAZARDOUS COMPONENTS
3 HAZARDS IDENTIFICATION
4 FIRST AID MEASURES
Skin
Remove contaminated clothing. Wash skin thoroughly with soap and water or use recognized skin cleanser. Do not use
solvents or thinners.
Eye
Irrigate copiously with clean, fresh water for at least 10 minutes, holding the eyelids apart and seek medical advice.
Inhalation
Remove to fresh air, keep patient warm and at rest, if breathing is irregular or stopped, administer artificial respiration. If
unconscious place in recovery position and seek medical advice.
Ingestion
If accidentally swallowed obtain immediate medical attention. Keep at rest. Do not induce vomiting.
Medical Conditions Aggravated by Exposure
Exposure to component solvents vapors concentration in excess of the stated occupational exposure limit may result in
adverse health effects such as mucous membrane and respiratory system irritation and adverse effect on kidney, liver and
central nervous system.
5 FIRE FIGHTING MEASURES
Extinguishing Media
Recommended: alcohol resistant foam, co2, powders, water spray. Not to be used: waterjet. Recommendations: due to
the organic solvents content of the preparation, fire will produce dense black smoke. Exposure to decomposition products
may cause a health hazard. Appropriate breathing apparatus may be required. Cool closed containers exposed to fire with
water. Do not allow run-off from fire fighting to enter drains or water courses.
Printed On 31-Mar-03
ND = No Data NA = Not Applicable NI = Not Indicated
268 INK TF/Z PRINTING MEDIUM HD
Material Id Trade Name 1/ 3
101 C
Flash Point
0.8
Flammability Limits in Air, Lower, % by Volume
6 ACCIDENTAL RELEASE MEASURES
Spill or Leak Procedure
Due to the organic solvents content of the preparation: exclude sources of ignition and ventilate the area. Avoid breathing
vapors. Refer to protective measures listed below. Contain and collect spillage with non-combustible absorbent materials,
e.g., sand, earth, vermiculite, diatomaceous earth and place in container for disposal according to local regulations. Do not
allow to enter drains or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates
lakes, rivers or sewages, inform appropriate authorities in accordance with local regulations.
7 HANDLING & STORAGE
Storage
Due to the organic solvents content of the preparation: vapors are heavier than air and may spread along floors. Vapors
may form explosive mixtures with air. Prevent the creation of flammable or explosive concentrations of vapor in air and
avoid vapor concentration higher than the occupational exposure limits. Additionally, the product should only be used in
areas from which all naked lights and other sources of ignition have been exluded. Electrical equipment should be
protected to the appropriate standard. Keep container tightly closed. Isolate from sources of heat, sparks and open flame.
No sparking tools should be used. Avoid skin and eye contact. Avoid inhalation of vapor and spray mist. Smoking, eating
and drinking are forbidden in application area. Comply with the health and safety at work laws. Always keep in containers of
same material as the original one. Never use pressure to empty: container is not a pressure vessel. Storage in accordance
with the regulations of the corresponding authorities. Observe label precaution. Store between 15 and 30c in a dry, well
ventilated place away from sources of heat and direct sunlight. Due to the organic solvents content of the preparation: keep
away from sources of ignition. Keep away from oxidizing agents, from strongly alkaline and strongly acid materials. No
smoking. Prevent unauthorized access. Containers which are opened must be carefully resealed and kept upright to
prevent leakage.
Ventilation
Provide adequate ventilation. Where reasonably practicable, this should be achieved by the use of local exhaust
ventilation and good general extraction. If these are not sufficient to maintain concentrations of particles and solvent vapor
below the OEL, suitable respiratory protection must be worn.
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Eye Protection: Personal Protection Equipments (PPE)
Use safety eyewear designed to protect against splash of liquids.
Skin Protection: Personal Protection Equipments (PPE)
All parts of the body should be washed after contact. For prolonged or repeated contact, use nitrile, neoprene or latex
rubber gloves. Barrier creams may help to protect the exposed areas of the skin, they should however, not be applied once
exposure has occurred.
Respiratory Protection: Personal Protection Equipments (PPE)
When workers are facing concentrations above the exposure limit, they must use appropriate certified respirators.
9 PHYSICAL & CHEMICAL PROPERTIES
Odor and Appearance
Liquid - very light smell
100 C
Boiling Point
0
Specific Gravity
NI
Melting Point
20 C
Vapor Pressure
NI
Evaporation Rate
NI
Vapor Density
Partially miscible
Solubility In Water
Printed On 31-Mar-03
ND = No Data NA = Not Applicable NI = Not Indicated
268 INK TF/Z PRINTING MEDIUM HD
Material Id Trade Name 2/ 3
10 STABILITY & REACTIVITY
Stability/Incompatibility
Stable under recommended storage and handling conditions. When exposed to high termperatures may produce
hazardous
Hazardous Reactions/Decomposition Products
Exposure to decomposition products may cause a health hazard.
11 TOXICOLOGICAL INFORMATION
Routes of Exposure
Skin: wash well with soap and water ingestion: if swallowed, consult a physician
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Do not allow into drains or water courses. Empty containers are to be deposited according to the official rules.
14 TRANSPORT INFORMATION
15 REGULATORY INFORMATION
NFPA Ratings
Health Flammability Reactivity Special Hazards
HMIS Ratings
Health 1 Flammability 0 Reactivity 0 Personal Prot. Equip. F
16 OTHER INFORMATION
Disclaimer
The information of this msds is based on the present state of our knowledge and on current EEC and national laws, as the
users working conditions are beyond our knowledge and control. The product is not to be used for other purposes than
those specified under section 1 without first obtaining written handling instruction. It is always the responsibility of the user
to take all necessary steps in order to fulfill the demand laid down in the local rules and legislation. The information in this
msds is meant as a description of the safety requirements of our product; it is not to be considered as a guarantee of the
products properties. The information in this safety data sheet is required pursuant to dangerous substances regulations
1984.
12/30/1997 12/30/1997
Replaces Sheet Dated
Completed On
TRANS TECH AMERICA, INC.
Completed By
Printed On 31-Mar-03
ND = No Data NA = Not Applicable NI = Not Indicated
268 INK TF/Z PRINTING MEDIUM HD
Material Id Trade Name 3/ 3
|