MATERIAL SAFETY DATA SHEET
1 CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Trade Name INK TYPE UVG
469
MSDS Number
ITW TRANS TECH
Supplier
475 N. GARY AVENUE
CAROL STREAM, IL 60188 USA
Telephone Numbers - 24 Hour Emergency Assistance
Emergency (352)323-3500
Telephone Numbers - General Assistance
Information (630)752-4000
2 COMPOSITION / INFORMATION ON INGREDIENTS
Concentration
Ingredient Name CAS Number Exposure Limits / Health Hazards
N-BUTYLACETATE 123-86-4 < 17 % OSHA TWA: 150ppm OSHA STEL:
200ppm ACGIH TLV: 150ppm
STEL: 200 ppm
XYLENES 1330-20-7 <4% OSHA PEL: 100ppm ACGIH TLV:
100ppm
1-METHOXYPROPYLACEATE-2 108-65-6 <2% Not established.
Same as above.
CYCLOHEXANONE 108-94-1 <3% ACGIH TLV: 25ppm -OSHA TWA-
50ppm (MAK)
ACRYLATED OLIGOMER AND Trade Secret < 30 % Not established.
MONOMER BLEND* Irritant, potential sensitizer
KETONE DERIVATIVE Trade Secret < 10 % Not established.
Potential irritant.
Composition Comments
The exact formula of this product is a trade secret.
3 HAZARDS IDENTIFICATION
Emergency Overview
Prolonged or repeated exposures can cause sensitization. Irritation may be delayed, so exposure can go unnoticed. Avoid
all direct contact.
Potential Health Effects, Skin
Skin contact, especially if prolonged, may cause irritation, rash or chemical burn to the contacted area. Effects of exposure
may be delayed 24 to 48 hours.
Potential Health Effects, Eye
Eye contact with the liquid is expected to cause severe irritation and possibly injury to the cornea.
Potential Health Effects, Inhalation
Vapors may cause irritation to eyes, skin and respiratory tract.
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
469 INK TYPE UVG
Material Id Trade Name 1/ 4
Potential Health Effects, Ingestion
Swallowing may cause nausea, vomiting, abdominal discomfort, or even internal injury.
Target Organs
Skin, eyes, central nervous system.
Effects of Long-Term (Chronic) Exposure
Prolonged or repeated exposures can cause sensitization. Irritation may be delayed, so exposure can go unnoticed. Avoid
all direct contact.
4 FIRST AID MEASURES
Skin
Wash affected area thoroughly with soap and water. Wash contaminated clothing before re-use. If irritation develops and
persists, seek medical attention.
Eye
Flush with water for at least 15 minutes and seek a physician immediately.
Inhalation
Remove person to fresh air and restore breathing. Treat symptomatically. Consult a physician.
Ingestion
Do not induce vomiting. Consult a physician or poison control center immediately. Treat symptomatically.
5 FIRE FIGHTING MEASURES
Extinguishing Media
CO 2 or dry chemical.
Basic Fire Fighting Procedures
Use self-contained positive pressure breathing apparatus and protective clothing.
Unusual Fire & Explosion Hazards
Hazardous polymerization may occur. Using streams of cooling water to avoid this, if necessary.
119 - 130 F (Rapid-Tester Closed Cup)
Flash Point
Not established
Flammability Limits in Air, Lower, % by Volume
Not established
Flammability Limits in Air, Upper, % by Volume
6 ACCIDENTAL RELEASE MEASURES
Spill or Leak Procedure
Scoop up and collect excess material, using inert absorbent material. Collected material should be disposed in approved
fashion. Appropriate protective clothing, including rubber gloves and chemical splash goggles, should be worn during these
procedures.
7 HANDLING & STORAGE
Storage
Store in the dark away from excessive heat, sources of ignition, sunlight and other ultraviolet light sources. Store between
50潞 and 80潞F (10潞 and 27潞C).
Ventilation
This material should be used only with adequate ventilation. Use of local exhaust ducts, fume hoods and/or other
mechanical exhaust ventilation is recommended. Respiratory equipment is not required, unless ventilation provisions are
inadequate. NIOSH/MSHA approved respirators with organic vapor cartridges are recommended.
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
469 INK TYPE UVG
Material Id Trade Name 2/ 4
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Eye Protection: Personal Protection Equipments (PPE)
Wear chemical splash goggles. Do not wear contact lenses while handling this material.
Skin Protection: Personal Protection Equipments (PPE)
Wear chemical resistant gloves appropriate for handling acrylates, acetates and any associated cleanup solvents. Do not
use vinyl gloves. Inspect gloves frequently for cuts or holes and discard damaged gloves. Wash hands with soap and water
after handling this product. Do not clean skin with solvents; solvents might increase skin penetration by this product, as well
as being potentially toxic themselves.
Respiratory Protection: Personal Protection Equipments (PPE)
Respiratory equipment is not required, unless ventilation provisions are inadequate. NIOSH/MSHA approved respirators
with organic vapor cartridges are recommended.
General
Face shields, polyethylene aprons and tyvek outer garments afford general body/clothing protection.
Effects from the UV curing process:
Heat generated by UV light sources can volatilize small amounts of monomers before the polymerization is complete.
These volatilized monomers can be irritating if ventilation is inadequate.
9 PHYSICAL & CHEMICAL PROPERTIES
Odor and Appearance
Variously colored, viscous liquid, mild acrylic odor
ND
Boiling Point
1.02 - 1.25 %
Specific Gravity
< 27 % (by volume)
Percent Volatile
ND
Vapor Pressure
< 1 (butyl acetate=1)
Evaporation Rate
> 1 at 20 deg. C (air=1)
Vapor Density
Insoluble
Solubility In Water
2.5 lb/gal
Volatile Organic
10 STABILITY & REACTIVITY
Stability/Incompatibility
Stable.
Conditions to avoid: Excessive heat, sunlight and other UV light sources.
Materials to Avoid: Polymerization catalysts, oxidizing agents and peroxides.
Hazardous Reactions/Decomposition Products
Burning may produce carbon monoxide, nitrogen oxides and other toxic fumes. Incomplete combustion would result in the
boiling off of acrylic monomers and generation of smoke. No hazardous decomposition products are expected during
normal storage and usage conditions.
Hazardous Polymerization
May occur.
Conditions to avoid: Excessive heat, sunlight and other UV light sources, polymerization catalysts, peroxides, and
oxidizing agents.
11 TOXICOLOGICAL INFORMATION
12 ECOLOGICAL INFORMATION
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
469 INK TYPE UVG
Material Id Trade Name 3/ 4
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Chemical incinerator or state approved waste disposal site. Comply with federal, state and local regulations.
RCRA Hazardous Waste No: D001, due to ignitability
14 TRANSPORT INFORMATION
Department of Transportation (DOT) Requirements:
General Transportation Information for Bulk Shipments
Proper Shipping Name Printing Ink
Hazard Class Flammable Liquid UN/NA Code 1210
Labels Required Flammable Liquid
15 REGULATORY INFORMATION
Federal Regulations
TSCA Status: All ingredients are listed.
Title III - Clean Air Act - Hazardous Air Pollutants:
Section 112 - Cyclohexanone (SOCMI Chemical); Xylene (SOCMI Chemical, Hazardous, Organic and Volatile Air Pollutant)
CERCLA:
Reportable waste quantity (RQ): Cyclohexanone - 5,000 lbs.; Butyl acetate - 5,000 lbs.; Xylene - 1,000 lbs.
State Regulations
Massachusetts: Butyl acetate, xylene and cyclohexanone
New Jersey: Butyl acetate (#1329), xylene (#2014) and cyclohexanone (#570)
Pennsylvania: Butyl acetate, xylene and cyclohexanone (all are environmental hazards)
SARA TITLE III RATINGS
Immediate Hazard X Delayed Hazard X Fire Hazard X Pressure Hazard
Reactivity Hazard
WHMIS RATINGS
Compressed Gas Flammable/Combustible Oxidizer Acutely Toxic
Other Toxic Effects Bio Hazardous Corrosive Dangerously Reactive
NFPA Ratings
Health 2 Flammability 2 Reactivity 1 Special Hazards
HMIS Ratings
Health 2 Flammability 2 Reactivity 1 Personal Prot. Equip. H
Following ingredients of this product are listed in SARA313
SARA Listed Ingredient Name CAS Number Maximum %
XYLENES 1330-20-7 4.0
Listed on the following Regulatory List(s)
SARA 313
16 OTHER INFORMATION
Disclaimer
To the best of our knowledge, the information contained herein is accurate. However, Trans Tech America, Inc. does not
assume any liability whatsoever for the accuracy or completeness of this information. Final determination of suitability of
any material is the sole responsibility of the user. All materials may present unknown health hazards and should be used
with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that
exist.
6/23/2008 9/26/2007
Replaces Sheet Dated
Completed On
Completed By
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
469 INK TYPE UVG
Material Id Trade Name 4/ 4
|