MATERIAL SAFETY DATA SHEET
1 CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Trade Name INK UVC
ITW TRANS TECH
Supplier
475 N. GARY AVENUE
CAROL STREAM, IL 60188 USA
Telephone Numbers - 24 Hour Emergency Assistance
Emergency (352)323-3500
Telephone Numbers - General Assistance
Information (630)752-4000
2 COMPOSITION / INFORMATION ON INGREDIENTS
Concentration
Ingredient Name CAS Number Exposure Limits / Health Hazards
PROPRIETARY ORGANIC SOLVENT 30 - 40 OSHA PEL: 150ppm TWA, 200ppm
STEL
ACGIH TLV: 150ppm, 200ppm
STEL
PROPRIETARY ORGANIC 20 - 30 Not established.
RESINS/MONOMERS BLEND
Composition Comments
The exact formula of this product is a trade secret. See section 5 for additional health hazard information.
3 HAZARDS IDENTIFICATION
Potential Health Effects, Skin
Skin contact, especially if prolonged, may cause irritation, rash or chemical burn to the contacted area. Effects of exposure
may be delayed 24 to 48 hours.
Potential Health Effects, Eye
Eye contact with the liquid is expected to cause severe irritation and possibly injury to the cornea.
Potential Health Effects, Inhalation
Irritant to nose and respiratory tract.
Potential Health Effects, Ingestion
Swallowing may cause nausea, vomiting, abdominal discomfort, or even internal injury.
Signs & Symptoms of Short-Term (Acute) Exposure
Vapors may cause severe eye irritation, redness, tearing and blurred vision.
Effects of Long-Term (Chronic) Exposure
Prolonged or repeated exposures can cause sensitization. Irritation may be delayed, so exposure can go unnoticed. Avoid
all direct contact.
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
573 INK UVC
Material Id Trade Name 1/ 4
4 FIRST AID MEASURES
Skin
Wash exposed area with soap and water. Wash contaminated clothing thoroughly before reuse. If irritation persists or if
contact has been prolonged, obtain medical attention.
Eye
Flush with water for at least 15 minutes and seek a physician immediately.
Inhalation
Remove to fresh air and keep warm. Call for a physician.
Ingestion
If appreciable quantities are ingested, seek medical attention.
Medical Conditions Aggravated by Exposure
Prolonged or repeated exposures can cause sensitization. Irritation may be delayed, so exposure can go unnoticed. Avoid
all direct contact.
5 FIRE FIGHTING MEASURES
Extinguishing Media
CO 2 or dry chemical.
Basic Fire Fighting Procedures
Use self-contained positive pressure breathing apparatus and protective clothing.
Unusual Fire & Explosion Hazards
Hazardous polymerization may occur. Use streams of cooling water to avoid this if necessary.
54 - 57 潞C
Flash Point
Not established
Flammability Limits in Air, Lower, % by Volume
Not established
Flammability Limits in Air, Upper, % by Volume
6 ACCIDENTAL RELEASE MEASURES
Spill or Leak Procedure
Dam spills and absorb with inert material such as sand. Wear appropriate protective clothing and respiratory protection
equipment when entering the spill area.
7 HANDLING & STORAGE
Storage
Store in a cool and dark atmosphere. Keep containers cool, dry and away from ignition sources. Store out of direct sunlight.
Ventilation
This material should be used only with adequate ventilation. Use of local exhaust ducts, fume hoods and/or other
mechanical exhaust ventilation is recommended. Respiratory equipment is not required, unless ventilation provisions are
inadequate. If needed, NIOSH/MSHA approved respirators with organic vapor cartridges are recommended. Heat
generated by UV light sources can volatilize small amounts of monomers before the polymerization is complete. These
volatilized monomers can be irritating if ventilation is inadequate.
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Eye Protection: Personal Protection Equipments (PPE)
Chemical splash goggles. Contact lenses should not be worn when working with this chemical.
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
573 INK UVC
Material Id Trade Name 2/ 4
Skin Protection: Personal Protection Equipments (PPE)
Wear chemical resistant gloves appropriate for handling acrylates, acetates and any associated cleanup solvents. Do not
use vinyl gloves. Inspect gloves frequently for cuts or holes and discard damaged gloves. Wash hands with soap and water
after handling this product. Do not clean skin with solvents; solvents might increase skin penetration by this product, as well
as being potentially toxic themselves.
Respiratory Protection: Personal Protection Equipments (PPE)
Adequate ventilation is required. Use of local exhaust ducts, fume hoods and/or other mechanical exhaust ventilation is
recommended. Respiratory equipment is not required, unless ventilation provisions are inadequate to meet PEL's.
NIOSH/MSHA approved respirators with organic vapor cartridges and particulate prefilters are recommended.
9 PHYSICAL & CHEMICAL PROPERTIES
Odor and Appearance
Variously colored paste with odor of organic solvents.
Not established
Boiling Point
0.9 - 1.05 water = 1
Specific Gravity
30 - 40 %
Percent Volatile
Not determined
Vapor Pressure
<1
Evaporation Rate
> 1 at 20潞C
Vapor Density
Insoluble
Solubility In Water
2.5 - 3.3 lb/gal
Volatile Organic
10 STABILITY & REACTIVITY
Stability/Incompatibility
Stable under normal conditions of use.
Conditions to avoid: Excessive heat, sunlight and other UV light sources.
Materials to Avoid: Polymerization catalysts, oxidizing agents and peroxides.
Hazardous Reactions/Decomposition Products
Burning may produce carbon monoxide. Incomplete combustion would result in the boiling off of acrylic monomers and
generation of smoke. No hazardous decomposition products are expected during normal storage and use.
Hazardous Polymerization
May occur. Conditions to avoid: Excessive heat, sunlight and other UV light sources, polymerization catalysts, peroxides,
and oxidizing agents.
11 TOXICOLOGICAL INFORMATION
Routes of Exposure
Inhalation of vapors, direct contact with skin or eyes. Target organs: Skin, eyes, and respiratory tract.
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Chemical incinerator or state approved waste disposal site. Comply with federal, state and local regulations.
14 TRANSPORT INFORMATION
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
573 INK UVC
Material Id Trade Name 3/ 4
Department of Transportation (DOT) Requirements:
General Transportation Information for Bulk Shipments
Proper Shipping Name Printing ink
UN/NA Code 1210
Packaging Group III
Labels Required Flammable Liquid
15 REGULATORY INFORMATION
Federal Regulations
Toxic Substances Control Act (TSCA) Status: All ingredients are listed.
NFPA Ratings
Health Flammability Reactivity Special Hazards
HMIS Ratings
Health 2 Flammability 2 Reactivity 1 Personal Prot. Equip. B
16 OTHER INFORMATION
Disclaimer
To the best of our knowledge, the information contained herein is accurate. However, Trans Tech does not assume any
liability whatsoever for the accuracy or completeness of this information. Final determination of suitability of any material is
the sole responsibility of the user. All materials may present unknown health hazards and should be used with caution.
Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
6/23/2008 10/30/2003
Replaces Sheet Dated
Completed On
`
Completed By
Printed On 23-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
573 INK UVC
Material Id Trade Name 4/ 4
|