MATERIAL SAFETY DATA SHEET
1 CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Trade Name INK UP82GL
ITW TRANS TECH
Supplier
475 N. GARY AVENUE
CAROL STREAM, IL 60188 USA
Telephone Numbers - 24 Hour Emergency Assistance
Emergency (352)323-3500
Telephone Numbers - General Assistance
Information (630)752-4000
2 COMPOSITION / INFORMATION ON INGREDIENTS
Concentration
Ingredient Name CAS Number Exposure Limits / Health Hazards
2-BUTOXYETHYLACETATE 112-07-2 20 - 25 Other Exposure Limits: 20ppm
(MAK)
1-METHOXY PROPYL ACETATE-2 108-65-6 12 - 13 OSHA PELs: Not established.
ACGIH TLV: Not established.
OSHA/NIOSH IDLH TLV*: 275
mg/m3
CYCLOHEXANONE 108-94-1 5 ACGIH TLV: 100 mg/m3
1,2,4-TRIMETHYL BENZENE 95-63-6 1.6 OSHA PEL: 25ppm ACGIH TLV:
25ppm OSHA/NIOSH IDLH TLV*:
Not established.
Composition Comments
100% Reaction product - A bisphenol - Epichlorohydrin: epoxy resin
(Average Molecular Weight> 700 CAS EINECS 025036-25-3).
3 HAZARDS IDENTIFICATION
Potential Health Effects, Skin
Irritation of the skin, including redness, dermatitis, allergic eczema.
Potential Health Effects, Inhalation
In high concentrations can be irritating to the mucous membranes. Anesthetic effect.
Potential Health Effects, Ingestion
Harmful if swallowed. May cause nausea, vomiting, diarrhea.
Signs & Symptoms of Short-Term (Acute) Exposure
Dizziness, nausea, irritation of the skin and mucous membranes.
Effects of Long-Term (Chronic) Exposure
(Cyclohexanone): Eye cataracts, liver damage, kidney damage
Printed On 24-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
547 INK UP82GL
Material Id Trade Name 1/ 5
4 FIRST AID MEASURES
Skin
Wash affected area with mild soap and water.
Eye
Flush immediately with large amounts of water for at least 15 minutes.
Inhalation
Remove to fresh air and keep warm. If breathing is difficult: artificial respiration. Call for a physician.
Ingestion
Do not induce vomiting. Dilute any effect by drinking water and get immediate medical attention.
Medical Conditions Aggravated by Exposure
Not Determined
5 FIRE FIGHTING MEASURES
Extinguishing Media
Alcohol resistant foam, co2, powders, water spray.
Basic Fire Fighting Procedures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Use respiratory
protection independent of recirculated air.
Unusual Fire & Explosion Hazards
Water may be used to cool tightly closed containers to prevent pressure build-up due to extreme heat. Keep contianers
tightly closed, isolate from heat, sparks, electrical equipment and open flame.
46 潞C Closed Cup
Flash Point
0.8
Flammability Limits in Air, Lower, % by Volume
6 ACCIDENTAL RELEASE MEASURES
Environmental Precautions
Do not empty into drains. Dispose of or incinerate in accordance with local, state and federal regulations.
Spill or Leak Procedure
Remove sources of ignition. Ventilate area. Contain and collect spillage with non-combustible absorbent materials, e.g.
sand, earth, vermiculite, diatomaceous earth and place in container for disposal according to local regulations.
7 HANDLING & STORAGE
Handling
Use only in well ventilated areas. When using do not eat, drink or smoke. No smoking.
Storage
Store in cool ventilated area. Keep container tightly closed when not in use and during transport. Do not store above +50C.
Store in accordance with NFPA, state and local standards
Ventilation
Local exhaust if in confined areas. Vapors are heavier than air and may spread along floors. Vapors may form explosive
mixtures with air. Remove vapors from floor.
Printed On 24-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
547 INK UP82GL
Material Id Trade Name 2/ 5
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Controls
Inks are not suited for spray applications.
Eye Protection: Personal Protection Equipments (PPE)
Safety goggles.
Skin Protection: Personal Protection Equipments (PPE)
Avoid skin contact with this material. Use appropriate protective gloves when handling. Personnel should wear protective
clothing.
Respiratory Protection: Personal Protection Equipments (PPE)
Wear a NIOSH approved respirator.
General
Remove and wash contaminated clothing before reuse. Wash hands thoroughly before eating, drinking, smoking, or using
toilet facilities.
9 PHYSICAL & CHEMICAL PROPERTIES
Odor and Appearance
Variously colored paste with odor of organic solvents.
137 - 192 潞C
Boiling Point
1.03 g/cm3 at 20C
Specific Gravity
NA
Melting Point
34 - 71 (4.1 lb/gal or 492 g/l approx)
Percent Volatile
> 0.7 KPa
Vapor Pressure
NA (Butyl Acetate = 1)
Evaporation Rate
>1
Vapor Density
90 sec. DIN CUP 4mm
Viscosity
Not Soluble
Solubility In Water
10 STABILITY & REACTIVITY
Stability/Incompatibility
Stable under recommended storage and handling conditions. Keep away from oxidizing agents, strongly alkaline and
strongly acid materials in order to avoid exothermic reactions. Avoid contact with water.
Hazardous Reactions/Decomposition Products
When exposed to high temperatures may produce hazardous decomposition products such as carbon monoxide and
dioxide, smoke, oxides of nitrogen.
Hazardous Polymerization
Will not occur
Conditions to avoid: None foreseen.
11 TOXICOLOGICAL INFORMATION
Routes of Exposure
Inhalation, ingestion, skin and eye contact.
Carcinogenicity
I.A.R.C. MONOGRAPHS: No
OSHA: No
NATIONAL TOXICOLOGY PROGRAM: No
Printed On 24-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
547 INK UP82GL
Material Id Trade Name 3/ 5
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Dispose of in accordance with all federal, state, and local regulations.
14 TRANSPORT INFORMATION
Department of Transportation (DOT) Requirements:
General Transportation Information for Bulk Shipments
Proper Shipping Name Paint Related Material
Hazard Class 3 (Flammable Liquid) UN/NA Code 1210
15 REGULATORY INFORMATION
Federal Regulations
To ensure compliance with the Toxic Substances Control Act (TSCA), Sara Title III - Section 313 (40 CFR part 372), and
the California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65).
1-methoxy-2-propylacetate: CAS# 108-65-6, TSCA - Listed, SARA - Not Listed under Section 313, Prop. 65 - Not Listed
2-butoxyethylacetate: CAS# 112-07-2, TSCA - Listed, SARA - Listed under certain Glycol Esters (Sec.313), Prop. 65 - Not
Listed.
Cyclohexanone: CAS# 108-94-1, TSCA - Listed, SARA - Not Listed under Section 313, Prop. 65 - Not Listed.
1,2,4 trimethylbenzene: CAS# 95-63-6, TSCA - Listed, SARA - Listed under Section 313, Prop. 65 - Not Listed.
Please note that all of the components in this product are listed in the TSCA Chemical Inventory, 1985 Edition (and there
fore acceptable for use in the United States).
International Regulations
The European Standard, EN 71 "Safety of Toys", Part 3: Chemical Properties, Edition 1 of June 1982, provides the
requirements in regard to the content of substances hazardous to health in printing of toys, writing utensils, etc. The
supplier confirms that the product supplied with this MSDS complies with those requirements. The following values in
soluble elements are not exceeded:
100 ppm lead
250 ppm antimony
100 ppm arsenic
500 ppm barium
100 ppm cadmium
250 ppm chromium
100 ppm mercury
Also in conforming with EN 71, the supplier confirms that the sum concentration of the above listed Heavy Metals does not
exceed 100 ppm.
NFPA Ratings
Health Flammability Reactivity Special Hazards
HMIS Ratings
Health 3 Flammability 2 Reactivity 1 Personal Prot. Equip. C
16 OTHER INFORMATION
Disclaimer
The information contained herein is based on technical data believed to be reliable. However, since the conditions under
which this information may be applied are beyond our control, we can assume no liability for results of its application. This
information should be used only by a person having sufficient technical skill to make informed judgements regarding its
application.
Printed On 24-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
547 INK UP82GL
Material Id Trade Name 4/ 5
6/24/2008 1/24/2003
Replaces Sheet Dated
Completed On
`
Completed By
Printed On 24-Jun-08
ND = No Data NA = Not Applicable NI = Not Indicated
547 INK UP82GL
Material Id Trade Name 5/ 5
|