MATERIAL SAFETY DATA SHEET
1 CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Trade Name THINNER 412
ITW TRANS TECH
Supplier
475 N. GARY AVENUE
CAROL STREAM, IL 60188 USA
Telephone Numbers - 24 Hour Emergency Assistance
Emergency (352)323-3500
Telephone Numbers - General Assistance
Information (630)752-4000
2 COMPOSITION / INFORMATION ON INGREDIENTS
Composition Comments
This product contains Methylpolysiloxanes, which can generate Formaldehyde at approximately 300潞F (150潞C) and above,
in atmospheres which contain oxygen. Formaldehyde is a skin, eye, and throat irritant, is toxic and a potential cancer
hazard.
3 HAZARDS IDENTIFICATION
Potential Health Effects, Skin
May cause contact dermatitis on long exposure.
Potential Health Effects, Eye
Contact may result in irritation.
Potential Health Effects, Inhalation
May cause slight irritation to mucous membranes and upper respiratory tract.
Potential Health Effects, Ingestion
Very low toxicity expected. A likely laxative.
4 FIRST AID MEASURES
Skin
Remove with dry towel, then wash with soap and water. Remove and wash contaminated clothing.
Eye
Flush at least 15 minutes with water. Do not rub eyes. Seek medical advice in case of continuous irritation.
Inhalation
Remove to fresh air and keep warm. Give oxygen if breathing is difficult.
Ingestion
Do not induce vomiting. Seek medical attention.
Printed On 19-Feb-07
ND = No Data NA = Not Applicable NI = Not Indicated
624 THINNER 412
Material Id Trade Name 1/ 3
5 FIRE FIGHTING MEASURES
Hazardous Combustion Products
CO, CO2, SiO2, H2CO
Extinguishing Media
All standard media for chemical fires.
Basic Fire Fighting Procedures
Like all silicones, this product can produce Formaldehyde when strongly heated in air.
170 潞F (Setaflash)
Flash Point
NA
Flammability Limits in Air, Lower, % by Volume
NA
Flammability Limits in Air, Upper, % by Volume
6 ACCIDENTAL RELEASE MEASURES
Emergency Action
Pick up spilled material with absorbent clay, then wash area thoroughly with water and detergent. Spilled material is very
slippery.
7 HANDLING & STORAGE
Handling
Ground containers and all transfer equipment to prevent static build up.
Storage
Store in cool ventilated area. Store in cool (<85潞F), closed and dry containers. Keep containers tightly closed.
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Controls
Good general ventilation.
Eye Protection: Personal Protection Equipments (PPE)
Safety glasses with side shields.
Skin Protection: Personal Protection Equipments (PPE)
Suitable protective clothing and rubber or plastic gloves.
Respiratory Protection: Personal Protection Equipments (PPE)
Not required.
9 PHYSICAL & CHEMICAL PROPERTIES
Odor and Appearance
Clear liquid. Colorless, odorless
410 潞F (210潞C)
Boiling Point
0.95
Specific Gravity
NA
Vapor Density
None
Solubility In Water
10 STABILITY & REACTIVITY
Stability/Incompatibility
Stable under normal conditions of use.
Printed On 19-Feb-07
ND = No Data NA = Not Applicable NI = Not Indicated
624 THINNER 412
Material Id Trade Name 2/ 3
Hazardous Reactions/Decomposition Products
Decomposition Products: Only in fire conditions, see section 5
Materials to Avoid: None
Conditions to Avoid: Heat, sparks, and flame.
Hazardous Polymerization
Will not occur
11 TOXICOLOGICAL INFORMATION
Routes of Exposure
See section 3.
12 ECOLOGICAL INFORMATION
EcoToxicological Information
NA
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Comply with federal, state and local regulations.
14 TRANSPORT INFORMATION
Department of Transportation (DOT) Requirements:
General Transportation Information for Bulk Shipments
Proper Shipping Name Paint Related Material
UN/NA Code 1263
15 REGULATORY INFORMATION
Federal Regulations
TSCA INVENTORY STATUS: This material or all of its contents are listed on the Toxic Substances Control Act (TSCA).
NFPA Ratings
Health Flammability Reactivity Special Hazards
HMIS Ratings
Health 1 Flammability 2 Reactivity 0 Personal Prot. Equip. B
16 OTHER INFORMATION
Disclaimer
We believe the above information is correct as of the date of this data sheet. However, as this information and the
conditions under which the product are used are beyond the control of ITW Trans Tech, it is the user's obligation to
determine the conditions for the safe use of the product. No warranty, expressed or implied, is hereby made.
2/19/2007 2/19/2007
Replaces Sheet Dated
Completed On
Completed By
Printed On 19-Feb-07
ND = No Data NA = Not Applicable NI = Not Indicated
624 THINNER 412
Material Id Trade Name 3/ 3
|