NuGenTec
Grease Cutter 3 Page 1 of 7
PRD Number: GPR703 May 30, 2007
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Identification
----------------------
Product Name: Grease Cutter 3 Product Number: GPR703
Synonyms: Industrial Strength - Heavy Duty Degreaser
CAS Number: Blend
Company Identification
----------------------
www.nugentec.com
NuGeneration Technologies, LLC
100 Professional Center Drive Suite 101, Rohnert Park, CA 94928 USA
(707) 820-4080 (For product information)
1-800-424-9300 or 1-202-483-7616 (CHEMTREC: For emergencies)
2. COMPOSITION/INFORMATION ON INGREDIENTS
100.0% Grease Cutter 3
CONTAINING:
HAZARDOUS AND/OR REGULATED COMPONENTS
Chemical Name Amount CAS Number
------------- -------- ----------
2-BUTOXYETHANOL 5.0 - 10.0 % 111-76-2
SODIUM HYDROXIDE 1.0 - 5.0 % 1310-73-2
NON-HAZARDOUS COMPONENTS
Chemical Name Amount CAS Number
------------- -------- ----------
ANIONIC SURFACTANT 1.0 - 5.0 % 27177-77-1
NONIONIC SURFACTANT 5.0 - 10.0 % 68603-25-8
SODIUM SILICATE 1.0 - 5.0 % 13472-30-5
(See Section 8 for exposure guidelines)
(See Section 15 for regulatory information)
HAZARDS DISCLOSURE
This product contains hazardous materials as defined by the OSHA Hazard
Communication Standard 29 CFR 1910.1200.
As defined under Sara 311 and 312, this product contains materials that
are hazards.
MISCELLANEOUS:
Contains Sodium Hydroxide. Contains ethylene glycol monobutyl ether.
3. HAZARDS IDENTIFICATION
***************** EMERGENCY OVERVIEW *****************
* *
* WARNING *
* *
* Corrosive material. Avoid eye contact. Can causes *
* skin and eye irritation. *
* *
**********************************************************
NuGenTec
Grease Cutter 3 Page 2 of 7
PRD Number: GPR703 May 30, 2007
HMIS Rating - Health: 2
Flammability: 0
Reactivity: 0
Personal Protection Index: C
NFPA Rating - Health: 2
Flammability: 0
Reactivity: 0
Special Hazard: Corrosive
NFPA/HMIS Definitions: (0-Least, 1-Slight, 2-Moderate, 3-High,
4-Extreme). These values are obtained using the guidelines or published
evaluations prepared by the National Fire Protection Association (NFPA) or
the National Paint and Coating Association (for HMIS ratings).
POTENTIAL HEALTH EFFECTS
EYE:
Contact causes severe eye irritation and or burns.
SKIN:
Contact may cause severe skin irritation and possible burns.
INHALATION:
No hazards expected in normal industrial use at room temperature. Vapors
and/or aerosols which may be formed at elevated temperatures may be
irritating to eyes and respiratory tract.
INGESTION:
May be harmful if swallowed. Irritating to mouth, throat, and stomach.
SIGNS AND SYMPTOMS OF EXPOSURE:
If exposed areas are flushed promptly and thoroughly with water, there
should be little or no harm.
CHRONIC EFFECTS:
Prolonged and/or repeated contact may produce mild to moderate skin
irritation or inflammation and in some cases rashes or burns.
CARCINOGENICITY INFORMATION:
No known cancer hazards.
MISCELLANEOUS:
Solutions extremely slippery when spilled.
4. FIRST AID MEASURES
EYE CONTACT FIRST AID:
Hold eyelids apart and flush eyes with plenty of water for at least 15
minutes. Get medical attention if irritation develops or persists.
SKIN CONTACT FIRST AID:
Immediately wash skin with plenty of soap and water while removing
contaminated clothing and shoes. Get medical attention if irritation
develops or persists.
NuGenTec
Grease Cutter 3 Page 3 of 7
PRD Number: GPR703 May 30, 2007
INHALATION FIRST AID:
Although this product is not known to cause respiratory problems, if
breathing is difficult, remove to fresh air and provide oxygen. Get
medical attention if cough or other symptoms develop.
Remove from area of exposure. Seek immediate medical attention if
respiratory irritation or distress continues.
INGESTION FIRST AID:
Give milk or water. Do not induce vomiting. Get medical attention
immediately.
STATEMENT OF PRACTICAL TREATMENT:
Always have plenty of water available for first aid.
NOTES TO PHYSICIAN:
Treat patient symptomatically.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
COC Flash Point: None TCC Flash Point: None
Autoignition Temperature: None
FLAMMABLE LIMITS IN AIR
LEL: None
UEL: None
EXTINGUISHING MEDIA:
Will not burn.
FIRE & EXPLOSION HAZARDS:
Material will not burn.
FIRE FIGHTING INSTRUCTIONS:
Contaminated extinguishing water must be disposed of in accordance with
applicable regulations.
6. ACCIDENTAL RELEASE MEASURES
SAFEGUARDS (PERSONNEL):
Protect skin and eyes from exposure.
INITIAL CONTAINMENT:
Floor may become slippery. Contain spilled material. Wash area to
prevent slipping. Treat or dispose of waste material in accordance with
all local, state/provincial, and national requirements.
LARGE SPILLS PROCEDURE:
Forms smooth, slippery surfaces on floors, posing an accident risk. Clean
up spills immediately, observing precautions in Protective Equipment
section. Neutralize spill with a weak acid such as vinegar or acetic
acid. Flush spill area with water to wastewater treatment system. After
removal, flush contaminated area thoroughly with water. Or, absorb spill
with inert material (e g, dry sand or earth), then place in a chemical
waste container dispose of in an approved sanitary landfill. Treat or
NuGenTec
Grease Cutter 3 Page 4 of 7
PRD Number: GPR703 May 30, 2007
dispose of waste material in accordance with all local, state/provincial,
and national requirements.
SMALL SPILLS PROCEDURE:
Floor may become slippery. Wash with water or absorb spills with inert
material. Treat or dispose of waste material in accordance with all
local, state/provincial, and national requirements.
7. HANDLING AND STORAGE
RECOMMENDED STORAGE TEMPERATURE
Minimum: 4.4 C (39.9 F)
Maximum: 48.9 C (120.0 F)
HANDLING (PERSONNEL):
Avoid contact with eyes, skin, and clothing. Empty drums should be
completely drained (triple rinsed), properly bunged, and promptly returned
to a drum re-conditioner, or properly disposed of. Wash hands thoroughly
after handling. Wash contaminated clothing before reuse.
HANDLING (PHYSICAL ASPECTS):
Keep container closed to avoid contamination.
STORAGE PRECAUTIONS:
Store in a cool dry place. Do not stack drums more than three pallets
high. Store in a tightly closed container.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING CONTROLS:
Good general ventilation should be sufficient to control airborne levels.
Facilities storing or utilizing this material should be equipped with an
eyewash facility and a safety shower.
EYE / FACE PROTECTION REQUIREMENTS:
When splashing of the material may occur, chemical goggles and a face
shield are recommended.
SKIN PROTECTION REQUIREMENTS:
Wear protective gloves to minimize skin contact. Nitrile rubber and PVC
are suitable protective materials; Neoprene is recommended. Wash hands
thoroughly after handling.
RESPIRATORY PROTECTION REQUIREMENTS:
Under normal use conditions, with adequate ventilation, no special
handling equipment is required.
MISCELLANEOUS:
Where an apron and protective clothing.
EXPOSURE GUIDELINES:
No Information Available.
NuGenTec
Grease Cutter 3 Page 5 of 7
PRD Number: GPR703 May 30, 2007
9. PHYSICAL AND CHEMICAL PROPERTIES
FORM ...............................: Liquid
COLOR ..............................: No color
ODOR ...............................: Faint Odor
BOILING POINT ......................: >212 F
SOLUBILITY IN WATER ................: Complete
SPECIFIC GRAVITY ...................: 1.110 (Water = 1)
BULK DENSITY .......................: 9.26
MELTING/FREEZING POINT .............: 32 F
PH .................................: 13.5
% VOLATILES ........................: 6%
VOLATILE ORGANIC COMPOUNDS (VOC) ...: 60 g/L
PH (5% B.V.) .......................: 12.8
10. STABILITY AND REACTIVITY
STABILITY:
Stable.
POLYMERIZATION:
Hazardous polymerization will not occur.
INCOMPATIBILITY WITH OTHER MATERIALS:
May react with acidic materials.
DECOMPOSITION:
Decomposition will not occur if handled and stored properly. Product may
decompose at temperatures above 270掳C and release carbon, nitrogen or
oxides.
CONDITIONS TO AVOID:
This material is safe under normal storage and handling conditions.
11. TOXICOLOGICAL INFORMATION
EYE EFFECTS:
Can cause severe eye irritation.
SKIN EFFECTS:
Contact may cause skin irritation.
ACUTE ORAL EFFECTS:
No know hazards in normal industrial use.
ACUTE INHALATION EFFECTS:
No know hazards in normal industrial use.
12. ECOLOGICAL INFORMATION
No information available.
NuGenTec
Grease Cutter 3 Page 6 of 7
PRD Number: GPR703 May 30, 2007
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL:
Uncleaned empty containers should be disposed of in the same manner as
the contents. Dilute or neutralize with acid and discharge to an
industrial sewage treatment facility. Or bury in an approved sanitary
landfill. Treat or dispose of waste material in accordance with all
local, state/provincial, and national requirements. For additional waste
disposal information contact your local NuGenTec representative at (888)
99-NuGen.
CONTAMINATED MATERIALS:
Wash contaminated clothing before reuse.
CONTAINER DISPOSAL:
Clean out containers prior to disposal.
14. TRANSPORTATION INFORMATION
PRODUCT LABEL .............: Grease Cutter 3
D.O.T. SHIPPING NAME ......: Corrosive Liquid
TECHNICAL SHIPPING NAME ...: Corrosive Liquid, NOS (Sodium Hydroxide)
D.O.T. HAZARD CLASS .......: 8
UN NUMBER .................: 1760 Corrosive Liquid, NOS
PRODUCT RQ (LBS) ..........: 100,000
D.O.T. LABEL ..............: Corrosive Liquid, Packing Group III
D.O.T. PLACARD ............: #8
BULK CLASS ................: N/A
PACKAGE CLASS .............: 55, PG III
MISCELLANEOUS:
Export Classification, organic surface-active agents (other than soap),
washing preparations and cleaning preparations, schedule B # 3402.90.5030.
15. REGULATORY INFORMATION
EEC Symbols and Indications of Danger:
Corrosive (C)
R-Phrases:
R35 - Causes severe burns.
S-Phrases:
S24/25 - Avoid contact with skin and eyes.
Canadian Disclosure List
Sodium Hydroxide (1310-73-2)
2-butoxyethanol (111-76-2)
SARA Title III - Section 313
2-butoxyethanol (111-76-2)
CERCLA Hazardous Substances
Sodium Hydroxide (1310-73-2) -- RQ 1000 lb
NuGenTec
Grease Cutter 3 Page 7 of 7
PRD Number: GPR703 May 30, 2007
SC Toxic Air Pollutants List
Sodium Hydroxide (1310-73-2)
FDA (FOOD AND DRUG ADMINISTRATION):
This Product Meets FDA/USDA requirements for cleaning in the food
processing industry.
MISCELLANEOUS INFORMATION:
This material or all of its components are listed on the Inventory of
Existing Chemical Substances under the Toxic Substance Control Act
(TSCA). This material or all of its components are listed on the
Canadian Domestic Substances List (DSL). This material or all of its
components are listed (or considered as having been notified) on the
European Inventory of Existing Chemical Substances (EINECS).
16. OTHER INFORMATION
PREPARED BY .......: Donato Polignone
APPROVAL DATE .....: May 30, 2007
SUPERCEDES DATE ...: November 18, 2002
PRD NUMBER ........: GPR703 (Official Copy)
ADDITIONAL INFORMATION:
The data in this Material Safety Data Sheet relates only to the specific
material designated herein. It does not relate to use in combination
with any other material or in any process.
**********************************************************************
This information is furnished without warranty, expressed or implied,
except that it is accurate to the best knowledge of NuGeneration
Technologies, LLC. The data on this sheet are related only to the
specific material designated herein. NuGeneration Technologies, LLC
assumes no legal responsibility for use or reliance upon these data.
**********************************************************************
END OF MSDS
**********************************************************************
|