NuGenTec NuEtch E2 Page 1 of 2
MATERIAL SAFETY DATA SHEET
PRD Number: MCE204 May 31, 2007
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: NuEtch E2 Product #: MCE204 CAS Number: Blend
NuGeneration Technologies, LLC www.nugentec.com
100 Professional Center Drive Suite 101, Rohnert Park, CA 94928 USA (707)820-4080 (product info)
1-800-424-9300 or 1-202-483-7616 (CHEMTREC: For emergencies)
2. COMPOSITION/INFORMATION ON INGREDIENTS:
HAZARDOUS AND/OR REGULATED COMPONENTS
Chemical Name Amount CAS Number
SODIUM HYDROXIDE < 50.0 % 1310-73-2
COMPOSITION COMMENT: Biodegradable, Corrosive product. [High Caustic Aluminum Etchant]
HAZARDS DISCLOSURE: This product contains known hazardous materials as defined by the OSHA Hazard
Communication Standard 29 CFR 1910.1200. As defined under Sara 311 and 312, this product does not contain(s)
known hazardous materials.
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW - DANGER!
Corrosive LIQUID: Sodium Hydroxide - Alkaline Cleaning compound,
causes skin and eye irritation, rash or burns.
HMIS/NFPA Rating:
Health - 3, Flammability - 0, Reactivity - 1
NFPA/HMIS Definitions: (0-Least, 1-Slight, 2-Moderate, 3-High, 4-Extreme).
POTENTIAL HEALTH EFFECTS
EYE: Contact may cause eye irritation or permanent Tissue Burns. INGESTION: May be harmful if swallowed.
SKIN: Contact may cause skin irritation, rash or tissue burns.
INHALATION: Do not inhale aerosols of this product especially those from Aluminum etching processes.
SIGNS AND SYMPTOMS OF EXPOSURE: Exposure may lead to rash or burn.
CHRONIC EFFECTS: Prolonged/repeated contact may produce rash or burns.
CARCINOGENICITY INFORMATION: No known cancer hazards.
4. FIRST AID MEASURES
EYE CONTACT FIRST AID: Flush eyes with plenty of water for at least 15 minutes. Get medical attention immediately.
SKIN CONTACT FIRST AID: Wash skin with water and remove contaminated clothing. Wash before reuse.
INHALATION FIRST AID: Remove to fresh air if questionable. Seek Medical attention if irritation persists.
INGESTION FIRST AID: Get medical attention. DO not - Induce vomiting. Give water or Milk or Calcium tablets.
STATEMENT OF PRACTICAL TREATMENT: Always have plenty of water available for first aid.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES: Autoignition Temp: None COC Flash Point: None TCC Flash Point: None
FLAMMABLE LIMITS IN AIR: LEL: None; UEL: None EXTINGUISHING MEDIA: Will not burn.
FIRE & EXPLOSION HAZARDS: Incinerating may create toxic decomposition products.
6. ACCIDENTAL RELEASE MEASURES
SPILLS PROCEDURE: Wash to waste treatment system with water. Or for large spills Absorb spill with inert material
(dry sand), then place in a chemical waste container.
7. HANDLING AND STORAGE
RECOMMENDED STORAGE TEMPERATURE Minimum: 4.4C (40F) Maximum: 48.9C (120F)
SHELF LIFE(in original sealed containers): 5 years @ 4.4 C 3 years @ 48.9 C
HANDLING (PERSONNEL): Avoid contact with eyes, skin, and clothing.
ALUMINUM ETCHING: This product produces hazardous and corrosive mist of flammable and hydrogen gas
aluminum etching processes. Use with adequate ventilation. And keep area away from sources of ignition.
STORAGE PRECAUTIONS: Keep from freezing. Keep container closed when not in use.
NuGeneration Technologies, LLC www.nugentec.com
NuGenTec NuEtch E2 Page 2 of 2
MATERIAL SAFETY DATA SHEET
PRD Number: MCE204 May 31, 2007
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING CONTROLS: Under normal use conditions, with adequate ventilation, no special handling equipment
is required.
EYE PROTECTION REQUIREMENTS: Wear protective Glasses and face-shield to minimize eye contact.
EYE / FACE / RESPIRATORY PROTECTION REQUIREMENTS: Rubber, nitrile or neoprene protective coverings.
SKIN PROTECTION REQUIREMENTS: Wear protective gloves and rubber apron to minimize skin contamination.
9. PHYSICAL AND CHEMICAL PROPERTIES
FORM: Liquid COLOR: Amber
ODOR: Mild BOILING POINT: >212 F
SOLUBILITY IN WATER: Complete SPECIFIC GRAVITY: 1.510 (Water = 1)
BULK DENSITY: 12.6 MELTING/FREEZING POINT: <32 F
PH: 14 PH @ 5%: 13.3 VOC = 0 g/l (concentrate)
10. STABILITY AND REACTIVITY
STABILITY: Stable. POLYMERIZATION: Hazardous polymerization will not occur.
INCOMPATIBILITY WITH OTHER MATERIALS: Avoid contact with Acidic conditions. May corrode copper,
aluminum, zinc, and their alloys. DECOMPOSITION: Decomposition will not occur if handled and stored properly.
11. TOXICOLOGICAL INFORMATION
EYE / SKIN EFFECTS: Contact may cause eye irritation or tissue burns.
12. ECOLOGICAL INFORMATION - No information available.
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL: Treat or dispose of waste material in accordance with all local, state, and national requirements.
CONTAMINATED MATERIALS: Wash contaminated clothing before reuse.
CONTAINER DISPOSAL: Triple Rinse containers prior to disposal.
14. TRANSPORTATION INFORMATION
PRODUCT LABEL: NuEtch E2 PACKAGE CLASS: 55
D.O.T. SHIPPING NAME: Corrosive Liquid, NOS (Sodium Hydroxide) D.O.T. HAZARD CLASS: 8
UN NUMBER: 1760 D.O.T. LABEL: Corrosive Liquid
PRODUCT RQ (LBS): 2,000 D.O.T. Packing Group: III BULK CLASS: N/A
15. REGULATORY INFORMATION
FDA (FOOD AND DRUG ADMINISTRATION): This Product Meets FDA/USDA requirements for cleaning in the food processing industry.
EEC Symbols and Indications of Danger: Corrosive (C) WHMIS Hazard Symbols: Class E - Corrosive Material
R-Phrases: R35 - Causes severe burns. S-Phrases: S24/25 - Avoid contact with skin and eyes.
Canadian Disclosure List Sodium Hydroxide (1310-73-2)
SARA Title III - Section 313 NONE SC Toxic Air Pollutants List Sodium Hydroxide (1310-73-2)
CERCLA Hazardous Substances Sodium Hydroxide (1310-73-2) -- RQ 1000 lb
This material or all of its components are listed on the Inventory of Existing Chemical Substances under the Toxic Substance Control Act
(TSCA). This material or all of its components are listed on the Canadian Domestic Substances List (DSL). This material or all of its
components are listed (or considered as having been notified) on the European Inventory of Existing Chemical Substances (EINECS).
16. OTHER INFORMATION
PREPARED BY: Donato Polignone PRD NUMBER: MCE204 (Official Copy)
APPROVAL DATE: May 31, 2007 SUPERCEDES DATE: March 3, 2004
The data in this Material Safety Data Sheet relates only to the specific material designated herein. It does not relate to use in
combination with any other material or in any process.
This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of NuGeneration
Technologies, LLC. The data on this sheet are related only to the specific material designated herein. NuGeneration Technologies, LLC
assumes no legal responsibility for use or reliance upon these data.
END OF MSDS
NuGeneration Technologies, LLC www.nugentec.com
|