DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 1 of 10
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
DICYANDIAMIDE
SYNONYMS
C2-H4-N4, H2NC(NH)(NHCN), dicyanodiamide, cyanoguanidine, "guanidine, cyano-", DICY, 2
-Cyanoguanidine, 2-Cyanoguanidine
PRODUCT USE
Fertilizers; nitrocellulose stabiliser; organic synthesis; pharmaceutical products;
dyestuffs; explosives; retarding rancidity in fats and oils; fireproofing compounds; case-
hardening preparations. Also used in cleaning compounds; soldering compounds; accelerator;
thinner for oil well drilling muds; stabiliser in detergent compositions; modifier for
starch products; catalyst for epoxy resins.
SUPPLIER
Company: Quantum Chemicals Pty Ltd
Address:
70 Quantum Close
Dandenong South
Victoria 3175
Telephone: 03 8795 8000
Emergency Tel: 1300 131 001
Fax: 03 8795 8099
HAZARD RATINGS
Flammability
Toxicity
Body Contact
Reactivity
Chronic
SCALE: Min/Nil=0 Low=1 Moderate=2 High=3 Extreme=4
Section 2 - HAZARDS IDENTIFICATION
STATEMENT OF HAZARDOUS NATURE
NON-HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of
NOHSC, and the ADG Code.
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 2 of 10
Section 2 - HAZARDS IDENTIFICATION
POISONS SCHEDULE
None
RISK SAFETY
Contact with acids liberates very toxic gas. Do not breathe dust.
Ingestion may produce health damage*. Take off immediately all contaminated clothing.
Cumulative effects may result following
exposure*.
* (limited evidence).
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
dicyandiamide 461-58-5 > 99
Section 4 - FIRST AID MEASURES
SWALLOWED
For advice, contact a Poisons Information Centre or a doctor.
路 IF SWALLOWED, REFER FOR MEDICAL ATTENTION, WHERE POSSIBLE, WITHOUT DELAY.
路 For advice, contact a Poisons Information Centre or a doctor.
Where Medical attention is not immediately available or where the patient is more than 15
minutes from a hospital or unless instructed otherwise:
路 Induce vomiting with fingers down the back of the of the throat, ONLY IF CONSCIOUS.
路 Lean patient forward or place on left side (head-down position if possible) to maintain
open airway and prevent aspiration.
NOTE: Wear a protective glove when inducing vomiting by mechanical means.
路 In the mean time, qualified first-aid personnel should treat the patient following
observation and employing supportive measures as indicated by the patient's condition.
路 If the services of a medical officer or medical doctor are readily available, the
patient should be placed in his/her care and a copy of the MSDS should be provided.
Further action will be the responsibility of the medical specialist.
路 If medical attention is not available on the worksite or surroundings send the patient
to a hospital together with a copy of the MSDS.
EYE
If this product comes in contact with the eyes:
路 Wash out immediately with fresh running water.
路 Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and
moving the eyelids by occasionally lifting the upper and lower lids.
路 If pain persists or recurs seek medical attention.
路 Removal of contact lenses after an eye injury should only be undertaken by skilled
personnel.
SKIN
If skin contact occurs:
路 Immediately remove all contaminated clothing, including footwear.
路 Flush skin and hair with running water (and soap if available).
路 Seek medical attention in event of irritation.
INHALED
路 If dust is inhaled, remove from contaminated area.
路 Encourage patient to blow nose to ensure clear passage of breathing.
路 If irritation or discomfort persists seek medical attention.
NOTES TO PHYSICIAN
路 Signs symptoms of acute cyanide poisoning reflect cellular hypoxia and are often non
-specific.
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 3 of 10
Section 4 - FIRST AID MEASURES
路 Cyanosis may be a late finding.
路 A bradycardic, hypertensive and tachypneic patient suggests poisoning especially if CNS
and cardiovascular depression subsequently occurs.
路 Immediate attention should be directed towards assisted ventilation, administration of
100% oxygen, insertion of intravenous lines and institution of cardiac monitoring.
路 Obtain an arterial blood gas immediately and correct any severe metabolic acidosis (pH
below 7.15).
路 Mildly symptomatic patients generally require supportive care alone. Nitrites should
not be given indiscriminately - in all cases of moderate to severe poisoning, they should
be given in conjunction with thiosulfate. As a temporizing measure supply amyl nitrite
perles (0.2ml inhaled 30 seconds every minute) until intravenous lines for sodium nitrite
are established. 10 ml of a 3% solution is administered over 4 minutes to produce 20%
methaemoglobin in adults. Follow directly with 50 ml of 25% sodium thiosulfate, at the
same rate, IV. If symptoms reappear or persist within 1/2-1 hour, repeat nitrite and
thiosulfate at 50% of initial dose. As the mode of action involves the metabolic
conversion of the thiosulfate to thiocyanate, renal failure may enhance thiocyanate
toxicity.
路 Methylene blue is not an antidote. [Ellenhorn and Barceloux: Medical Toxicology]
If amyl nitrite intervention is employed then Medical Treatment Kits should contain the
following:
路 One box containing one dozen amyl nitrite ampoules
路 Two sterile ampoules of sodium nitrite solution (10 mL of a 3% solution in each)
路 Two sterile ampoules of sodium thiosulfate solution (50 mL of a 25% solution in each)
路 One 10 mL sterile syringe. One 50 mL sterile syringe. Two sterile intravenous needles.
One tourniquet.
路 One dozen gauze pads.
路 Latex gloves
路 A "Biohazard" bag for disposal of bloody/contaminated equipment.
路 A set of cyanide instructions on first aid and medical treatment.
- Notes on the use of amyl nitrite:-
路 AN is highly volatile and flammable - do not smoke or use around a source of ignition.
路 If treating patient in a windy or draughty area provide some shelter or protection
(shirt, wall, drum, cupped hand etc.) to prevent amyl nitrite vapour from being blown
away. Keep ampoule upwind from the nose, the objective is to get amyl nitrite into the
patients lungs.
路 Rescuers should avoid AN inhalation to avoid becoming dizzy and losing competence.
路 Lay the patient down. Since AN dilates blood vessels and lowers blood pressure, lying
down will help keep patient conscious.
路 DO NOT overuse - excessive use might put the patient into shock. Experience at DuPont
plants has not shown any serious after-effects from treatment with amyl nitrite.
ADDITIONAL NOTES:
路 Major medical treatment procedures may vary e.g. US (FDA method as recommended by
DuPont) uses amyl nitrite as a methaemoglobin generator, followed by treatment with
sodium nitrite and then sodium thiosulfate.
MODES OF ACTION: Amyl nitrite (AN) reacts with haemoglobin (HB) to form about 5%
methaemoglobin (MHB). Sodium nitrite (NaNO2) reacts with haemoglobin to form
approximately 20-30% methaemoglobin. Methaemoglobin attracts cyanide ions (CN) from
tissue and binds with them to become cyanmethaemoglobin (CNMHB). Sodium thiosulfate
(Na2S2O3) converts cyanmethaemoglobin to thiocyanate (HSCN) which is excreted by the
kidneys. i.e. AN + HB = MHB NaNO2 + HB = MHB CN + MHB = CNMHB Na2S2O3 + CNMHB + O2 = HSCN
路 The administration of the antidote salts is intravenous in normal saline, Ringers
lactate or other available IV fluid.
路 European practice may use 4-dimethylaminophenol (DMAP) as a methaemoglobin generator.
Also hydroxycobalamin (Vitamin B12a) is used. Hydroxycobalamin works by reacting with
cyanide to form cyanocobalamin (Vitamin B12) which is excreted in the urine.
路 European and Australian NOHSC (Worksafe) propose dicobalt edetate (Kelocyanor) as
antidote. This acts by chelating cyanide to form stable cobalticyanide, which is excreted
in the urine. In all cases hyperbaric therapy may increase the efficiency of a cyanide
antidote kit.
Nitriles may produce metabolic cyanide.
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 4 of 10
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
路 Foam.
路 Dry chemical powder.
路 BCF (where regulations permit).
路 Carbon dioxide.
路 Water spray or fog - Large fires only.
FIRE FIGHTING
路 Use water delivered as a fine spray to control fire and cool adjacent area.
路 Do not approach containers suspected to be hot.
路 Cool fire exposed containers with water spray from a protected location.
路 If safe to do so, remove containers from path of fire.
路 Equipment should be thoroughly decontaminated after use.
FIRE/EXPLOSION HAZARD
路 Solid which exhibits difficult combustion or is difficult to ignite.
路 Avoid generating dust, particularly clouds of dust in a confined or unventilated space
as dusts may form an explosive mixture with air, and any source of ignition, i.e.
flame or spark, will cause fire or explosion. Dust clouds generated by the fine
grinding of the solid are a particular hazard; accumulations of fine dust may burn
rapidly and fiercely if ignited.
路 Dry dust can also be charged electrostatically by turbulence, pneumatic transport,
pouring, in exhaust ducts and during transport.
路 Build-up of electrostatic charge may be prevented by bonding and grounding.
路 Powder handling equipment such as dust collectors, dryers and mills may require
additional protection measures such as explosion venting.
路 All movable parts coming in contact with this material should have a speed of less than
1-metre/sec.
Combustion products include: carbon monoxide (CO) and nitrogen oxides (NOx).
FIRE INCOMPATIBILITY
Avoid contamination with strong oxidising agents as ignition may result.
HAZCHEM: None
Section 6 - ACCIDENTAL RELEASE MEASURES
EMERGENCY PROCEDURES
MINOR SPILLS
路 Clean up all spills immediately.
路 Avoid contact with skin and eyes.
路 Wear impervious gloves and safety glasses.
路 Use dry clean up procedures and avoid generating dust.
路 Sweep up or
路 Vacuum up (consider explosion-proof machines designed to be grounded during storage and
use).
路 Place spilled material in clean, dry, sealable, labelled container.
MAJOR SPILLS
路 Clear area of personnel and move upwind.
路 Alert Fire Brigade and tell them location and nature of hazard.
路 Wear breathing apparatus plus protective gloves.
路 Prevent, by any means available, spillage from entering drains or water course.
路 Stop leak if safe to do so.
路 Contain spill with sand, earth or vermiculite.
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 5 of 10
Section 6 - ACCIDENTAL RELEASE MEASURES
路 Collect recoverable product into labelled containers for recycling.
路 Neutralise/decontaminate residue.
路 Collect solid residues and seal in labelled drums for disposal.
路 Wash area and prevent runoff into drains.
路 After clean up operations, decontaminate and launder all protective clothing and
equipment before storing and re-using.
路 If contamination of drains or waterways occurs, advise emergency services.
EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all individuals could be exposed
for up to one hour WITHOUT experiencing or developing
life-threatening health effects is:
dicyandiamide 200 mg/m鲁
irreversible or other serious effects or symptoms which could impair an individual's ability to take
protective action is:
dicyandiamide 10 mg/m鲁
other than mild, transient adverse effects without perceiving a clearly defined odour is:
dicyandiamide 1.5 mg/m鲁
The threshold concentration below which most people will experience no appreciable risk of health effects:
dicyandiamide 0.5 mg/m鲁
American Industrial Hygiene Association (AIHA)
Ingredients considered according to the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
路 Avoid all personal contact, including inhalation.
路 Wear protective clothing when risk of exposure occurs.
路 Use in a well-ventilated area.
路 Avoid contact with moisture.
路 Avoid contact with incompatible materials.
路 When handling, DO NOT eat, drink or smoke.
路 Keep containers securely sealed when not in use.
路 Avoid physical damage to containers.
路 Always wash hands with soap and water after handling.
路 Work clothes should be laundered separately. Launder contaminated clothing before re
-use.
路 Use good occupational work practice.
路 Observe manufacturer's storing and handling recommendations.
路 Atmosphere should be regularly checked against established exposure standards to ensure
safe working conditions are maintained.
SUITABLE CONTAINER
路 Polyethylene or polypropylene container.
路 Packing as recommended by manufacturer.
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 6 of 10
Section 7 - HANDLING AND STORAGE
路 Check all containers are clearly labelled and free from leaks.
STORAGE INCOMPATIBILITY
Avoid reaction with oxidising agents, bases and strong reducing agents.
Avoid strong acids.
STORAGE REQUIREMENTS
路 Keep dry.
路 Store in original containers.
路 Keep containers securely sealed.
路 No smoking, naked lights or ignition sources.
路 Store in a cool, dry, well-ventilated area.
路 Store away from incompatible materials.
路 Protect containers against physical damage.
路 Check regularly for leaks.
路 Observe manufacturer's storing and handling recommendations.
_____________________________________________________
SAFE STORAGE WITH OTHER CLASSIFIED CHEMICALS
+ + + + + +
_____________________________________________________
+: May be stored together
O: May be stored together with specific preventions
X: Must not be stored together
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source Material TWA mg/m鲁
_________ _________ _____
Australia Exposure Standards dicyandiamide (Inspirable dust 10
(Not specified))
PERSONAL PROTECTION
EYE
路 Safety glasses.
路 Safety glasses with side shields.
路 Chemical goggles.
路 Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens or
restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account
of injury experience. Medical and first-aid personnel should be trained in their removal
and suitable equipment should be readily available. In the event of chemical exposure,
begin eye irrigation immediately and remove contact lens as soon as practicable. Lens
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 7 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
should be removed at the first signs of eye redness or irritation - lens should be
removed in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].
HANDS/FEET
Wear general protective gloves, eg. light weight rubber gloves.
OTHER
Overalls.
路 Impervious protective clothing.
路 Eyewash unit.
RESPIRATOR
Protection Factor Half- Face Respirator Full- Face Respirator Powered Air Respirator
10 x ES P1 Air- line* -- PAPR- P1 -
50 x ES Air- line** P2 PAPR- P2
100 x ES - P3 -
Air- line* -
100+ x ES - Air- line** PAPR- P3
* - Negative pressure demand ** - Continuous flow.
The local concentration of material, quantity and conditions of use determine the type of
personal protective equipment required.
For further information consult site specific
CHEMWATCH data (if available), or your
Occupational Health and Safety Advisor.
ENGINEERING CONTROLS
General exhaust is adequate under normal operating conditions. If risk of overexposure
exists, wear SAA approved respirator. Correct fit is essential to obtain adequate
protection. Provide adequate ventilation in warehouse or closed storage areas. Air
contaminants generated in the workplace possess varying "escape" velocities which, in
turn, determine the "capture velocities" of fresh circulating air required to effectively
remove the contaminant.
Type of Contaminant: Air Speed:
solvent, vapours, degreasing etc., evaporating 0.25- 0.5 m/s (50- 100 f/min)
from tank (in still air)
aerosols, fumes from pouring operations, 0.5- 1 m/s (100- 200 f/min.)
intermittent container filling, low speed
conveyer transfers, welding, spray drift,
plating acid fumes, pickling (released at low
velocity into zone of active generation)
direct spray, spray painting in shallow booths, 1- 2.5 m/s (200- 500 f/min)
drum filling, conveyer loading, crusher dusts,
gas discharge (active generation into zone of
rapid air motion)
grinding, abrasive blasting, tumbling, high 2.5- 10 m/s (500- 2000 f/min.)
speed wheel generated dusts (released at high
initial velocity into zone of very high rapid
air motion).
Within each range the appropriate value depends on:
Lower end of the range Upper end of the range
1: Room air currents minimal or favourable to 1: Disturbing room air currents
capture
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 8 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
2: Contaminants of low toxicity or of nuisance 2: Contaminants of high toxicity
value only
3: Intermittent, low production. 3: High production, heavy use
4: Large hood or large air mass in motion 4: Small hood - local control only
Simple theory shows that air velocity falls rapidly with distance away from the opening
of a simple extraction pipe. Velocity generally decreases with the square of distance
from the extraction point (in simple cases). Therefore the air speed at the extraction
point should be adjusted, accordingly, after reference to distance from the contaminating
source. The air velocity at the extraction fan, for example, should be a minimum of 1-2
m/s (200-400 f/min.) for extraction of solvents generated in a tank 2 meters distant from
the extraction point. Other mechanical considerations, producing performance deficits
within the extraction apparatus, make it essential that theoretical air velocities are
multiplied by factors of 10 or more when extraction systems are installed or used.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Odourless white crystals; mixes with water (2.26% @ 13 C). Soluble in liquid ammonia,
alcohol, ammonium hydroxide, acetone.
PHYSICAL PROPERTIES
Solid.
Mixes with water.
Contact with acids liberates very toxic gas.
Molecular Weight: 84.10 Boiling Range (掳C): Not available.
Melting Range (掳C): 98.3 Specific Gravity (water=1): 1.40
Solubility in water (g/L): Miscible pH (as supplied): Not applicable
pH (1% solution): Not available. Vapour Pressure (kPa): Negligible
Volatile Component (%vol): Negligible Evaporation Rate: Not applicable
Relative Vapour Density (air=1): >1 Flash Point (掳C): Not available
Lower Explosive Limit (%): Not available Upper Explosive Limit (%): Not available
Autoignition Temp (掳C): Not available Decomposition Temp (掳C): Not available.
State: Divided solid Viscosity: Not available
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
路 Presence of incompatible materials.
路 Product is considered stable.
路 Hazardous polymerisation will not occur.
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
Considered an unlikely route of entry in commercial/industrial environments.
The material is moderately discomforting to the gastro-intestinal tract and may be
harmful if swallowed in large quantity.
Nitrile poisoning exhibits similar symptoms to poisoning due to hydrogen cyanide. The
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 9 of 10
Section 11 - TOXICOLOGICAL INFORMATION
substances irritate the eyes and skin, and are absorbed quickly and completely through
the skin. The use of the term "organic nitriles" should be discouraged.
Cyanide poisoning can cause increased saliva output, nausea without vomiting, anxiety,
confusion, vertigo, dizziness, stiffness of the lower jaw, convulsions, spasm, paralysis,
coma and irregular heartbeat, and stimulation of breathing followed by failure. Often the
skin becomes cyanosed (blue-grey), and this is often delayed. Doses which are not lethal
are eventually excreted in the urine.
EYE
The material is moderately discomforting to the eyes and is capable of causing a mild,
temporary redness of the conjunctiva (similar to wind-burn), temporary impairment of
vision and/ or other transient eye damage/ ulceration.
SKIN
The material may be mildly discomforting to the skin.
Open cuts, abraded or irritated skin should not be exposed to this material. The material
may accentuate any pre-existing skin condition.
INHALED
The dust may be discomforting to the upper respiratory tract and may be harmful if
inhaled.
Persons with impaired respiratory function, airway diseases and conditions such as
emphysema or chronic bronchitis, may incur further disability if excessive concentrations
of particulate are inhaled.
CHRONIC HEALTH EFFECTS
Principal routes of exposure are by accidental skin and eye contact and inhalation of
generated dusts.
Chronic exposure to cyanides and certain nitriles may result in interference to iodine
uptake by thyroid gland and its consequent enlargement. This occurs following metabolic
conversion of the cyanide moiety to thiocyanate. Thyroid insufficiency may also occur as
a result of metabolic conversion of cyanides to the corresponding thiocyanate. Exposure
to small amounts of cyanide compounds over long periods are reported to cause loss of
appetite, headache, weakness, nausea, dizziness, abdominal pain, changes in taste and
smell, muscle cramps, weight loss, flushing of the face, persistent runny nose and
irritation of the upper respiratory tract and eyes. These symptoms are not specific to
cyanide exposure and therefore the existence of a chronic cyanide toxicity remains
speculative. Repeated minor contact with cyanides produce a characteristic rash with
itching, papules (small, superficial raised spots on the skin) and possible
sensitisation. Concerns have been expressed that low-level, long term exposures may
result in damage to the nerves of the eye.
Guanidine hydrochloride causes decrease in bone marrow activity usually shown as
gastrointestinal disturbance and "pins and needles" in the lips, face and extremities.
Irritability, tremor, inco-ordination and seizures can occur, rarely, there is low blood
pressure, skin reactions, low blood glucose and increased levels of creatinine. Asians
may be more susceptible. Chronic exposure may cause kidney damage.
TOXICITY AND IRRITATION
unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances.
TOXICITY IRRITATION
Oral (rat) LD50: 10000 mg/kg * Nil Reported
Oral (rat) TDLo: 273000 mg/kg/13W- C **[SKW]
Inhalation (rat) LC50: >0.259 mg/L/4h**
*[Cyanamide]
Inhalation (rat) TCLo: 2.4 mg/m鲁/4W- I
Dermal (rabbit) LD50: 10000 mg/kg *
DICYANDIAMIDE
Chemwatch Material Safety Data Sheet
Issue Date: 9-Mar-2007 CHEMWATCH 24059
NC317TCP Version No:4
CD 2007/3 Page 10 of 10
Section 12 - ECOLOGICAL INFORMATION
Oncorhynchus Mykiss LC50: 7700 mg/L/96h
Daphnia Magna EC50: 3177 mg/L/48h
Pseudomonas Putida EC10: 131 mg/L
Section 13 - DISPOSAL CONSIDERATIONS
路 Consult manufacturer for recycling options and recycle where possible .
路 Consult State Land Waste Management Authority for disposal.
路 Incinerate residue at an approved site.
路 Recycle containers if possible, or dispose of in an authorised landfill.
Section 14 - TRANSPORTATION INFORMATION
HAZCHEM: None
NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN, IATA,
IMDG
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE: None
REGULATIONS
dicyandiamide (CAS: 461-58-5) is found on the following regulatory lists;
Australia Exposure Standards
Australia Inventory of Chemical Substances (AICS)
International Council of Chemical Associations (ICCA) - High Production Volume List
OECD Representative List of High Production Volume (HPV) Chemicals
Section 16 - OTHER INFORMATION
MSDS SECTION CHANGES
The following table displays the version number of and date on which each section was last changed.
Section Name Version Date Section Name Version Date Section Name Version Date
Appearance 4 9- Mar- 2007 Transport 4 9- Mar- 2007
Classification of the preparation and its individual components has drawn on official and
authoritative sources as well as independent review by the Chemwatch Classification
committee using available literature references.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written permission
from CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 9-Mar-2007
Print Date: 19-Dec-2007
|