MATERIAL                 SAFETY             DATA        SHEET

HTS 929                                                                                    Page:   1

PRODUCT NAME: HTS 929                                                 HMIS CODES:  HFRP

PRODUCT CODE: rdI                                                                 330-

=================== SECTION I     -     MANUFACTURER IDENTIFICATION    ================================



MANUFACTURER'S NAME: Hesterman Technical Services Inc.                     DATE: March 1, 2004

ADDRESS            : 190 Hodsman Road

                     Regina, SK., Canada, S4N 5X4

EMERGENCY PHONE    : 1-613-996-6666

INFORMATION PHONE : (306)721-1339     FAX 306-721-3770



                        SECTION II      -   HAZARDOUS INGREDIENTS/SARA III INFORMATION

=====================                                                                       ===============



                                                             VAPOR PRESSURE                       WEIGHT

REPORTABLE COMPONENTS                          CAS NUMBER     mm Hg @         TEMP          PERCENT

 POLYORGANOSILOXANE                               N/A         N/A            77F/25C           80

 NAPTHA                                         64742-89-8    7.0           100F/38C           20



                                      SECTION III   -   PHYSICAL/CHEMICAL CHARACTERISTICS

===============================                                                               =============



BOILING RANGE: 118c-146c -(244F-295F)            SPECIFIC GRAVITY (H2O=1):     .733 @ 15C

VAPOR DENSITY: 4                                 EVAPORATION RATE:     <0.15 (Butyl Acetate = 1)

COATING V.O.C.:                                  COATING V.O.C.:

                  3.53 lb/gl                                           424 g/l

MATERIAL V.O.C.: 3.53 lb/gl                      MATERIAL V.O.C.:      424 g/l

SOLUBILITY IN WATER: INSOLUBLE                   APPEARANCE AND ODOR: SLIGHTLY THIXOTROPIC

                                                                 LIQUID, HYDROCARBON ODOR

===================== SECTION IV - FIRE AND EXPLOSION HAZARD DATA ===========================

FLASH POINT: 52F/11C PENSKY MARTENS CLOSED CUP.

FLAMMABLE LIMITS IN AIR BY VOLUME-        LOWER: 1%         UPPER: 7%

EXTINGUISHING MEDIA: FOAM, CO2, DRY CHEMICAL

SPECIAL FIREFIGHTING PROCEDURES

FIREFIGHTERS SHOULD WEAR SELF-CONTAINED BREATHING APPARATUS PRESSURE-DEMAND MSHA/NIOSH APPROVED OR

EQUIVALENT)TO PROTECT AGAINST THE HAZARDOUS EFFECTS OF COMBUSTION PRODUCTS AND OXYGEN DEFICIENCY. COOL

CONTAINERS EXPOSED TO FIRE WITH WATER.

UNUSUAL FIRE AND EXPLOSION HAZARDS

PRODUCT WILL BURN UNDER FIRE CONDITIONS. VAPOURS MAY TRAVEL A CONSIDERABLE DISTANCE TO A SOURCE OF

IGNITION AND FLASH BACK ALONG VAPOUR TRAIL. CLOSED CONTAINERS MAY EXPLODE (DUE TO THE BUILD-UP OF

PRESSURE) WHEN EXPOSED TO EXTREME HEAT. REACTS WITH WATER RELEASING HIGHLY FLAMMABLE AND EXPLOSIVE

VAPOURS.

HAZARDOUS DECOMPOSITION MATERIALS (UNDER FIRE CONDITIONS)

              FORMALDEHYDE

              OXIDES OF CARBON

              OXIDES OF SILICON

AUTO-IGNITION TEMPERATURE: 400C (752F)



===================================== SECTION V - REACTIVITY DATA ===============================

STABILITY: STABLE

CONDITIONS TO AVOID: AVOID PROLONGED HEATING OVER 100F/38C OR STORAGE BELOW 40F/4.4C. INCOMPATIBLE

WITH                        COMBUSTIBLE MATERIALS, HEAT, OPEN FLAME, SPARK, STATIC ELECTRICITY.

INCOMPATIBILITY (MATERIALS TO AVOID): STRONG BASES, STRONG ACIDS, STRONG OXIDIZING AGENTS.

HAZARDOUS DECOMPOSITION OR BYPRODUCTS: METHYL ETHYL KETOXIME, FORMALDEHYDE

HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.



==================== SECTION VI - TOXICOLOGICAL DATA ==============================================

INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE

REPEATED OR PROLONGED EXPOSURE TO VAPORS OR MISTS ARE IRRITATING TO THE EYES AND THE RESPIRATORY

TRACT. MAY CAUSE HEADACHES, DIZZINESS, NAUSEA, DROWSINESS, UNCONSCIOUSNESS AND OTHER CENTRAL NERVOUS

SYSTEM EFFECTS. VAPORS AND MISTS CAN IRRITATE EYES, NOSE AND RESPIRATORY TRACT. THIS PRODUCT CONTAINS

DIMETHYLPOLYSILOXANE WHICH CAN GENERATE SMALL AMOUNTS OF FORMALDEHYDE AS A BYPRODUCT OF OXIDATIVE

THERMAL DECOMPOSITION BEGINNING AT APPROXIMATELY 150C (300F). EXPOSURE TO FORMALDEHYDE CAN CAUSE

ADVERSE EFFECTS SUCH AS SKIN AND RESPIRATORY SENSITIZATION AND EYE AND THROAT IRRITATION.

FORMALDEHYDE IS A POTENTIAL CANCER HAZARD. USE GOOD INDUSTRIAL HYGIENE PRACTICES TO EVALUATE AND

CONTROL EXPOSURE TO FORMALDEHYDE WHEN WARRANTED BY CONDITIONS OF USE. Methylethylketoxime (cas 96-29-

7) EMITTED IN THE PRESENCE OF MOISTURE OR DURING CURING MAY CAUSE EYE IRRITATION AND POSSIBLE SKIN

SENSITIZATION.

SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE

SKIN: IRRITANT CAN CAUSE REDNESS, DRYNESS. LOSS OF NATURAL OILS, IRRITATION.

EYES: SEVERE IRRITANT. CAN CAUSE REDNESS, TISSUE DESTRUCTION IRRITATION.

INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE

INGESTION: HARMFUL IF INGESTED. CAN CAUSE BURNS TO MOUTH AND ESOPHAGUS, NAUSEA, VOMITING, ABDOMINAL

PAIN, LOSS OF APPETITE, LOSS OF COORDINATION.

HEALTH HAZARDS (ACUTE AND CHRONIC)

THIS PRODUCT CONTAINS DIMETHYLPOLYSILOXANE WHICH CAN GENERATE SMALL AMOUNTS OF FORMALDEHYDE AS A

BYPRODUCT OF OXIDATIVE THERMAL DECOMPOSITION BEGINNING AT APPROXIMATELY 150C (300F). EXPOSURE TO

FORMALDEHYDE CAN CAUSE ADVERSE EFFECTS SUCH AS SKIN AND RESPIRATORY SENSITIZATION AND EYE AND THROAT

IRRITATION. FORMALDEHYDE IS A POTENTIAL CANCER HAZARD. USE GOOD INDUSTRIAL HYGIENE PRACTICES TO

EVALUATE AND CONTROL EXPOSURE TO FORMALDEHYDE WHEN WARRANTED BY CONDITIONS OF USE.

Methylethylketoxime (cas 96-29-7) EMITTED IN THE PRESENCE OF MOISTURE OR DURING CURING MAY CAUSE EYE

IRRITATION AND POSSIBLE SKIN SENSITIZATION.

HTS 929      MATERIAL           SAFETY        DATA      SHEET                             Page:   2



CARCINOGENICITY: NTP CARCINOGEN: NO                     OSHA REGULATED: YES

THE INGREDIENTS ARE AT OR LESS THAN de minimis LEVELS OR ARE NOT CONSIDERED TO BE CARCINOGENS BY THE

NTP, IARC OR OSHA.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE

SKIN CONTACT MAY AGGRAVATE EXISTING SKIN DISEASE.



=========== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE =================================

PROTECTIVE GLOVES

THE USE OF NITRILE GLOVES IMPERMEABLE TO THE SPECIFIC MATERIAL HANDLED IS ADVISED TO PREVENT SKIN

CONTACT AND POSSIBLE IRRITATION. NOTE THAT PVA DEGRADES IN WATER.

EYE PROTECTION

CHEMICAL GOGGLES. IF SPLASHING MAY OCCUR OR DURING SPRAY OPERATIONS WEAR A FACE SHIELD, UNLESS A FULL

FACE PIECE RESPIRATOR IS USED. DO NOT WEAR CONTACT LENSES AS THEY MAY CONTRIBUTE TO THE SEVERITY OF

INJURY TO THE EYE FROM EXPOSURE TO LIQUID AND/OR VAPORS AND SPRAY MIST.

RESPIRATORY PROTECTION

FOLLOW OSHA REGULATION 29 CFR 1910.134 FOR RESPIRATOR USE. FOR CONFINED SPACE, INTERIOR APPLICATIONS

OR IF CONCENTRATION OF SOLVENTS IS NOT KNOWN, USE FULL FACE SUPPLIED AIR RESPIRATOR.

OTHER PROTECTIVE CLOTHING OR EQUIPMENT

ADDITIONAL PROTECTION MAY CONSIST OF APRONS, ARM COVERS OR A FULL BODY SUIT. TESTING OF SOME

COMMERCIALLY AVAILABLE PROTECTIVE CLOTHING INDICATES THAT CLOTHING CONSTRUCTED OF BUTYL RUBBER,

NITRILE RUBBER, SARANEX COATED TYVEK AND SOME NEOPRENE GARMENTS HAVE EXCELLENT RESISTANCE. CLOTHING

CONSTRUCTED OF NEOPRENE/LATEX RUBBER AND SOME PVC GARMENTS EXHIBITED LIMITED RESISTANCE TO PERMEATION.

CLOTHING CONSTRUCTED OF POLYETHYLENE, LATEX RUBBER, PVC OR POLY-LAMINATED TYVEK SHOWED LITTLE

RESISTANCE TO PERMEATION. PROTECTIVE CLOTHING SHOULD BE SELECTED AND USED IN ACCORDANCE WITH

"GUIDELINES FOR THE SELECTION OF CHEMICAL PROTECTIVE CLOTHING"PUBLISHED BY ACGIH. AMERICAN CONFERENCE

OF GOVERNMENTAL INDUSTRIAL HYGIENISTS).

WORK/HYGIENIC PRACTICES

WASH AT THE END OF EACH WORK SHIFT AND BEFORE EATING, SMOKING OR USING THE TOILET. PROMPTLY REMOVE

CONTAMINATED CLOTHING AND LAUNDER BEFORE WEARING. DISCARD CONTAMINATED LEATHER ARTICLES. EXAMINE

PROTECTIVE GLOVES AND CLOTHING BEFORE USE. DISCARD UPON FINDING EVIDENCE OF HOLES CRACKS OR LEAKS.

VENTILATION

IF CURRENT VENTILATION PRACTICES ARE NOT ADEQUATE DURING MIXING AND APPLICATION OPERATIONS TO MINIMIZE

EXPOSURE, USE EXPLOSION-PROOF LOCAL EXHAUST VENTILATION CAPABLE OF MAINTAINING EMISSIONS AT THE POINT

OF USE BELOW THE PEL OR TLV OR OTHER EXPOSURE GUIDELINES, AS APPROPRIATE. VENTILATION RATES SHOULD BE

MATCHED TO CONDITIONS. EXPLOSION-PROOF MECHANICAL EXHAUST VENTILATION, WITH VOLUME AND PATTERN CAPABLE

OF MAINTAINING A FRESH AIR SUPPLY, MAY BE NECESSARY IN CONFINED SPACES. REFER TO OSHA STANDARD 29 CFR

1910.94 FOR GUIDELINES. TURN OFF HEATING AND/OR AIR CONDITIONING EQUIPMENT TO PREVENT CONTAMINATING

BUILDING.

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED

SMALL SPILLS:

CLEAR THE AREA OF UNNECESSARY PERSONNEL. SHUT DOWN HVAC EQUIPMENT IF INSIDE BUILDING OR NEAR HVAC

SYSTEM TO PREVENT CONTAMINATING BUILDING. VENTILATE AREA AS VAPORS ARE HARMFUL, HEAVIER THAN AIR AND

ARE FLAMMABLE OR COMBUSTIBLE AND MAY MIGRATE TO AN IGNITION SOURCE. USE ONLY EXPLOSION PROOF

EQUIPMENT. INSURE A TRAINED RESPONSE TEAM IS IN EMERGENCY PROTECTIVE EQUIPMENT. PREVENT FURTHER

SPILLAGE AND CONTAIN THE SPILL USING DIKES MADE OF SAND, EARTH OR SPILL PILLOWS. COVER THE SPILL AREA

WITH A NON-COMBUSTIBLE ABSORBENT MATERIAL (E.G., ABSORBENT CLAY, EARTH, SAND) TO ABSORB AS MUCH LIQUID

AS POSSIBLE USING NON SPARKING TOOLS, CAREFULLY SHOVEL THE ABSORBENT INTO OPEN TOP CONTAINERS. DO NOT

FILL TO THE TOP OR COVER THE CONTAINERS.

LARGE SPILLS:

CLEAR THE AREA OF ALL NON-ESSENTIAL PERSONNEL. STAY UP-WIND TO AVOID BREATHING VAPOR. IF INSIDE A

BUILDING, OR NEAR HVAC EQUIPMENT, SHUT DOWN THE HVAC SYSTEM AND VENTILATE THE AREA AS VAPORS ARE

HARMFUL AND FLAMMABLE OR COMBUSTABLE AND MAY MIGRATE TO A SOURCE OF IGNITION.(IF MECHANICAL

VENTILATION EQUIPMENT IS TO BE USED TO VENTILATE THE AREA, USE ONLY EXPLOSION PROOF EQUIPMENT).

PREVENT ACCESS TO AREA. NOTIFY THE APPROPRIATE   LOCAL AND FEDERAL AUTHORITIES AS WELL AS THE MATERIAL

SUPPLIER. INSURE A TRAINED RESPONSE TEAM IS IN APPROPRIATE EMERGENCY EQUIPMENT. PREVENT FURTHER

SPILLAGE. CONTAIN THE SPILL USING SAND BAGS, SPILL PILLOWS, DIRT DIKES, ETC. IT IS IMPORTANT THAT THIS

MATERIAL NOT BE ALLOWED TO ENTER DRAINS. THE REACTION WITH WATER WILL FORM Methylethylketoxime (cas

96-29-7) EMITTED IN THE PRESENCE OF MOISTURE OR DURING CURING MAY CAUSE EYE IRRITATION AND POSSIBLE

SKIN SENSITIZATION. IF THIS MATERIAL DOES ENTER DRAINS, FLUSH WITH AMPLE QUANTITIES OF WATER AND

NOTIFY THE SEWER AUTHORITY IMMEDIATELY. ABSORB THE SPILL AND DECONTAMINATE THE SPILL AREA AND ABSORBED

MATERIAL AS IN SMALL SPILL ABOVE. TEST THE ATMOSPERE FOR RESIDUAL SOLVENT VAPORS BEFORE ALLOWING

OTHERS TO RE-ENTER THE AREA. WHEN SAFE CONDITIONS HAVE BEEN REESTABLISHED, REMOVE AND DECONTAMINATE

ALL EQUIPMENT USED.

SOLIDIFIED SPILLAGE:

WHERE SPILLS HAVE SOLIDIFIED, SANDBLASTING IS THE PREFERRED REMOVAL METHOD, PARTICULARLY FOR ROAD

SPILLS. WEAR SPECIAL PROTECTIVE CLOTHING FOR SANDBLASTING, ALONG WITH SELF-CONTAINED BREATHING

EQUIPMENT. CONTAMINATED SAND MUST BE COLLECTED FOR DECONTAMINATION AND DISPOSAL.

WASTE DISPOSAL METHOD

DISPOSE OF UNUSED PRODUCT OR CONTAMINATED PRODUCT AND MATERIALS USED IN CLEANING UP SPILLS OR LEAKS IN

A MANNER APPROVED FOR THIS MATERIAL. CONSULT APPROPRIATE FEDERAL, PROVINCIAL AND LOCAL REGULATORY

AGENCIES TO ASCERTAIN PROPER DISPOSAL PROCEDURES. INCINERATION IS ACCEPTABLE AND THE PREFERRED METHOD

OF DISPOSAL,

HOWEVER; NITROGEN OXIDE EMISSIONS CONTROLS MAY BE REQUIRED TO MEET SPECIFICATIONS. EMPTY CONTAINERS

WILL RETAIN PRODUCT RESIDUE AND VAPORS AND ARE SUBJECT TO PROPER WASTE DISPOSAL, AS ABOVE.

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING

STORE IN A COOL, DRY WELL VENTILATED AREA AWAY FROM IGNITION SOURCES AND INCOMPATIBLE MATERIALS IN

TIGHTLY CLOSED CONTAINERS TO PREVENT MOISTURE CONTAMINATION. UNUSED PRODUCT REMAINING IN OPENED

CONTAINERS MUST BE PURGED WITH DRY NITROGEN BEFORE RESEALING TO PREVENT CO2 PRESSURE BUILD-UP DUE TO

MOISTURE CONTAMINATION. IF MOISTURE OR WATER CONTAMINATION IS SUSPECTED, DO NOT RESEAL. OPEN SEALED

DRUMS SLOWLY TO RELEASE ANY PRESSURE DUE TO POSSIBLE BUILD-UP.

HTS 929               MATERIAL            SAFETY           DATA      SHEET                       Page:   3



OTHER PRECAUTIONS

DO NOT PUNCTURE, CUT, GRIND, WELD, BRAZE, SOLDER OR DRILL ON OR NEAR THIS CONTAINER OR OTHERWISE

EXPOSE SUCH CONTAINER TO HEAT, FLAME, SPARKS, STATIC ELECTRICAL CHARGES, ELECTRICITY OR OTHER SOURCES

OF IGNITION. THEY MAY EXPLODE AND/OR EMIT TOXIC VAPORS RESULTING IN INJURY OR DEATH. CLOSED CONTAINERS

MAY    EXPLODE DUE TO PRESSURE BUILD-UP IF EXPOSED TO WATER OR MOISTURE OR EXTREME HEAT. CONTAINERS,

EVEN THOSE THAT HAVE BEEN EMPTIED, WILL RETAIN PRODUCT RESIDUE AND VAPORS. ALWAYS OBEY HAZARD WARNINGS

AND HANDLE EMPTY CONTAINERS AS IF THEY WHERE FULL. DO NOT GET IN EYES, ON SKIN OR ON CLOTHING. AVOID

PROLONGED OR REPEATED BREATHING OF VAPOR OR SPRAY MIST. USE ONLY IN A WELL VENTILATED AREA. KEEP OUT

OF THE REACH OF CHILDREN.

SHIPPING INFORMATION

       SHIPPING NAME:       COATING SOLUTION

       HAZARD CLASS:        3

       UN NUMBER:           UN 1139

       PACKING GROUP:       II



                        SECTION VIII     - FIRST AID MEASURES

=====================                                            ========================================



EMERGENCY AND FIRST AID PROCEDURES

EYE: ABSORB EXCESS WITH CLEAN ABSORBENT CLOTH OR COTTON. FLUSH WITH CLEAN, LUKEWARM WATER FOR 15

MINUTES WHILE        LIFTING EYELIDS. REFER TO PHYSICIAN OR OPHTHALMOLOGIST FOR IMMEDIATE FOLLOW-UP.

SKIN: WIPE EXCESS MATERIAL OFF SKIN WITH A DRY CLOTH; THEN WASH SKIN WITH PLENTY OF SOAP AND WATER.

       WASH                 CLOTHING BEFORE REUSE. FOR SEVERE EXPOSURES, GET UNDER SAFETY SHOWER AND

       GET MEDICAL ATTENTION IF    IRRITATION OR ALLERGIC DERMATITIS SYMPTOMS DEVELOP, OR IF GROSS

       EXPOSURE DEVELOPS. FOR LESSER      EXPOSURES, SEEK MEDICAL ATTENTION IF IRRITATION PERSISTS.

INHALATION: MOVE TO FRESH AIR, ADMINISTER OXYGEN BY A QUALIFIED INDIVIDUAL OR ARTIFICIAL RESPIRATION

IF            NEEDED. GET MEDICAL ATTENTION.

INGESTION: DO NOT INDUCE VOMITING. DO NOT GIVE THE AFFECTED PERSON ANYTHING TO DRINK, EVEN IF FULLY

       CONSCIOUS. IF VOMITING OCCURS, KEEP VICTIMS HEAD BELOW THE HIPS TO PREVENT BREATHING VOMIT INTO

THE                  LUNGS. CONSULT PHYSICIAN IMMEDIATELY.

NOTE TO PHYSICIAN.

ALL TREATMENTS SHOULD BE BASED ON OBSERVED SIGNS AND SYMPTOMS OF DISTRESS IN THE PATIENT.

CONSIDERATION SHOULD BE GIVEN TO THE POSSIBILITY THAT OVEREXPOSURE TO MATERIALS OTHER THAN THIS

PRODUCT MAY HAVE OCCURRED.



                                       SECTION IX   -   DISCLAIMER

=================================                                    =======================================

PREPARED BY HESTERMAN TECHNICAL



THE INFORMATION   CONTAINED HEREIN IS FURNISHED WITHOUT WARRANTY OF ANY KIND. USERS SHOULD CONSIDER

THESE DATA ONLY   AS A SUPPLEMENT TO OTHER INFORMATION GATHERED BY THEM & DETERMINE THE SUITABILITY &

COMPLETENESS OF   INFORMATION FROM ALL SOURCES TO ASSURE PROPER USE & DISPOSAL OF THESE MATERIALS & THE

SAFETY & HEALTH   OF EMPLOYEES & CUSTOMERS.