IN THE EVENT OF A CHEMICAL EMERGENCY INVOLVING A SPILL, LEAK,
FIRE, EXPOSURE OR ACCIDENT CONTACT THE BELOW NUMBERS.
EMERGENCY 24 HOUR NUMBER GENERAL INFORMATION NUMBER
Material Safety Data Sheet CHEMTREC 1-800-424-9300 MAPEI 1-954-246-8888
CPSC STATEMENT DOT HAZARD CLASSIFICATION
WARNING - FLAMMABLE. VAPOR HARMFUL. SKIN AND EYE Adhesives, containing a flammable liquid; 3;
IRRITANT. HARMFUL OR FATAL IF SWALLOWED. UN1133; PGII
(contains Toluene and Isophorone Diamine)
IDENTITY (As shown on label):
Ultra/Bond G 19 Part B
Polyurethane Universal Adhesive for Rubber Floor Covering and Wood
Parquet
SECTION I - GENERAL INFORMATION SECTION II - PHYSICAL CHARACTERISTICS
MANUFACTURER: Maximum VOC N/E
MAPEI CORPORATION Boiling Point N/E
1144 East Newport Center Drive Vapor Pressure (mmHg) 24
Deerfield Beach, FL 33442 Vapor Density (AIR=1) >1.0
PREPARED BY: Specific Gravity (H20=1) 1.22
Donald House Melting Point (F) N/E
Manager of Product and Employee Safety Evaporation Rate (Butyl <1.0
Acetate=1)
PRINT DATE:
Friday, March 09, 2001 Solubility in water Insoluble
Appearance and Odor Amber liquid. Solvent odor.
VOC calculated per (Rule 1168, South Coast Air Quality District - California)
SECTION III - HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
Hazardous Components ACGIH Other Limits % Percent
(specific chemical identity; common names): OSHA (PEL) (TLV-TWA) Recommended (Optional)
Toluene (CAS# 108-88-3) 200ppm 50ppm 500ppm (NIOSH) 30 - 40%
Isophorone Diamine (CAS# 2855-13-2) N/E N/E N/E 50 - 60%
FOR CALIFORNIA: THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE TOXICITY.
HMIS (Hazardous Materials Identification System) Rating: Health - 3 Fire - 3 Reactivity - 0 Protection - H
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
Flash Point (F) - 40掳F (Toluene) Lower Explosive Limit (%) 鈥? 1.4 Upper Explosive Limit (%) 鈥? 6.7
Extinguishing Media
National Fire Protection Agency, Standard 704, recommends dry agent or foam for flash point < 73掳F.
Special Fire Fighting Procedures
Wear standard fire fighting gear with self-contained breathing apparatus.
Unusual Fire and Explosion Hazards
Vapors are heavier than air and may travel to an ignition source distant from the material handling point.
SECTION V - REACTIVITY DATA
STABILITY: Stable
Conditions to Avoid None known.
Incompatibility (Materials to Avoid) Hazard Decomposition of By-products
Strong oxidizing agents, strong acids, and strong bases. Carbon monoxide or carbon dioxide.
POLYMERIZATION: Will Not Occur
Conditions to Avoid
None known.
N/A = Not Applicable. N/E = Not Established. Ultra/Bond G 19 Part B MSDS Page 1 of 2
SECTION VI - HEALTH HAZARD DATA
ROUTES OF ENTRY: Inhalation? YES Skin? YES Ingestion? YES
HEALTH HAZARDS (ACUTE AND CHRONIC)
Acute: Inhalation or contact can cause irritation to eyes, skin, nose or throat to sensitive people. If ingested can cause
nausea, vomiting, griping, diarrhea, and depressed respirations.
Chronic: See Section III of MSDS.
CARCINOGENICITY: NTP - NO IARC - NO OSHA - NO
See Section III of MSDS.
Signs and Symptoms of Overexposure
Nausea; vomiting; nose and throat irritation; headaches; dizziness; confusion; eye irritation; and skin irritation.
Medical Conditions That Can Be Aggravated by Exposure
Allergies, skin and respiratory disorders. Product sensitivity.
EMERGENCY AND FIRST AID PROCEDURES
Eyes - Flush with cool water for 15 minutes while holding eyelid open. If irritation persists, seek medical attention
immediately.
Skin - Avoid contact with skin. Remove contaminated clothing. Wash affected area thoroughly with soap and water.
If irritation persists, seek immediate medical attention.
Inhalation - Remove to fresh air. If not breathing, trained personnel should initiate artificial respirations and immediate
medical attention should be obtained.
Ingestion - Do not induce vomiting. Do not give anything by mouth to an unconscious person. Seek medical attention
immediately.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be taken if Material is Leaked or Spilled
Keep spectators away. Eliminate all ignition sources (flames, hot surfaces and sources of electrical, static or frictional
sparks). Dike and contain spill with inert material (e.g. sand and earth). Transfer liquids to covered metal containers for
recovery or disposal, or remove with inert absorbent. USE ONLY NON-SPARKING TOOLS. Place absorbent diking materials
in covered metal containers for disposal. Prevent contamination of sewers, streams and groundwater with spilled material or
used absorbent.
Waste Disposal Method
Dispose of in accordance with local, state, and federal regulations governing your location.
Precautions to be taken during Handling and Storage
Keep container closed when not in use. Store at 60-95掳F and out of the sun. Use adequate ventilation to avoid breathing
vapors when cover is removed. Ground all equipment when handling flammable solvent-based materials.
Other Precautions
Containers may be hazardous when empty. Never use welding or cutting torch on or near drum (even when empty).
SECTION VIII - CONTROL MEASURES
Respiratory Protection: If workplace exposure limit of product is exceeded, a NIOSH/MSHA approved air supplied respirator is
required in absence of proper environmental control. Engineering or administrative controls should
be implemented to reduce exposure.
VENTILATION: Local Exhaust Special
Use in WELL VENTILATED areas only. N/A
Mechanical Other
Use only intrinsically safe devices. N/A
Eye Protection - Safety glasses or goggles as necessary to Protective Gloves - Impervious. (Nitrile, rubber, or better)
prevent eye contact.
Other Protective Equipment - As needed to minimize contact with skin.
WORK AND HYGIENE PRACTICE
Remove contaminated clothing immediately. Wash hands, after each use and before eating, drinking, or using toiletries.
Minimize contact of product on skins.
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data or the results
to be obtained from the use thereof. MAPEI Corporation assumes no responsibility for personal injury or property damage to vendees, users, or third parties caused by
the material. Such vendees or users assume all risks associated with the use of the material.
N/A = Not Applicable. N/E = Not Established. Ultra/Bond G 19 Part B MSDS Page 2 of 2
|