Material Safety Data Sheet UTG-GEL
Complies with OSHA's Hazard Communication
Standard 29 CFR 1910.1200.
DATE OF PREPARATION: MAY 2003
1. IDENTIFICATION
Product Name: Mobil grease FM 102
2. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Names and Synonyms: Aluminum complex grease
Globally reportable MSDS Ingredients:
Substance Name Approx Wt%
Aluminum Long-Chain Alkyl 5-15
Carboxylate (637-12-7)
Benzoic Acid, Aluminum Salt 1-5
(555-35-8)
See section 8 for exposure limits (if applicable)
Emergency Phone: 800-688-4005 (24 hours)
3. HAZARDS IDENTIFICATION
Under normal conditions of use, this product is not considered hazardous according to regulatory guidelines (see section 15).
Emergency Overview: Yellow grease. DOT ERG No. : NA
Potential Health effects: No significant effects expected.
For further health effects/toxicological data, see Section 11.
4. FIRST AID MEASURES
Eye Contact: Flush thoroughly with water. If irritation occurs, call a physician
Skin Contact: Was contact areas with soap and water. High pressure accidental injection through the skin requires immediate medical
attention for possible incision, irrigation and or debridement.
Inhalation: Not expected to be a problem.
Ingestion: Not expected to be a problem when ingested. If uncomfortable seek medical assistance.
5. FIRE FIGHTING HAZARD
Extinguishing Media: Carbon dioxide, foam, dry chemical and water fog.
Special Fire Fighting Procedures: Water or foam may cause frothing. Use water to keep fire exposed containers cool. Water spray
may be used to flush spills away from exposure. Prevent runoff from fire control or dilution from entering streams, sewers, or
drinking water supply.
Special Protective Equipment: For fires in enclosed areas, fire fighters must use self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: None
Combustion Products: Fumes, smoke, carbon monoxide, sulfur oxides, aldehyde and other decomposition products, in the case of
incomplete combustion.
Flash Point C(F): 224 (435) (Estimated for oil, ASTM D-92 (COC).
Flammable Limits (approx. % vol. in air)-LEL: NA UEL:NA
NFPA Hazard ID: Health: 0 Flammability: 1 Reactivity: 0
6. ACCIDENTAL RELEASE MEASURES
Notification Procedures: Report spills as required to appropriate authorities. U.S. Coast Guard regulations require immediate
reporting of spills that could reach any waterway including intermittent dry creeks. Report spill to Coast Guard toll free number (800)
424-8802. In case of accident or road spill notify CHEMTREC (800) 424-9300.
Procedures if Material is Released or Spilled: Shovel up and dispose of at an appropriate waste disposal facility in accordance with
current applicable laws and regulations, and product characteristics at time of disposal.
Environmental Precautions: Prevent spills from entering storm sewers or drains and contact with soil.
Personal Precautions: See Section 8
7. HANDLING AND STORAGE
Handling: No special precautions are necessary beyond normal good hygiene practices. See section 8 for additional personal
protection advice when handling this product.
Storage: Do not store in open or unlabeled containers. Store away from strong oxidizing agents or combustible material.
Special Precautions: Prevent small spills and leakages to avoid slip hazard.
Empty Container Warning: Empty containers retain residue (liquid and/or vapor) and can be dangerous. DO NOT Pressurize, cut
weld, braze, solder, drill, grind or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition; they
漏 1998 Goodson Shop Supplies
may explode and cause injury or death. Do not attempt to refill or clean container since residue is difficult to remove. Empty drums
should be completely drained, properly bunged and promptly returned to a drum reconditioned. All containers should be disposed of
in an environmentally safe manner and in accordance with governmental regulations.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
TWA STEL
Substance Name (CAS-NO) Source ppm mg/m3 ppm mg/m3
Aluminum Long-Chain Alkyl
Carboxylate (637-12-7)
Resp Fraction OSHA 5
Total Dust OSHA 10
Total Dust ACGIH 10
Benzoic Acid, Aluminum
Salt (555-32-8)
as Al Sol Salts OSHA 2
as Al Sol Salts ACGIH 2
Note: Limits shown for guidance only. Follow applicable regulations.
Ventilation: No special requirements under ordinary conditions of use and with adequate ventilation.
Eye Protection: Normal industrial eye protection practices should be employed.
Skin Protection: No special equipment required. However, good personal hygiene practices should always be followed.
9. PHYSICAL AND CHEMICAL PROPERTIES
Typical physical propertied are given below. Consult Product Data Sheet for specific details.
Appearance: Grease
Color: Yellow
Odor: Mild
Odor Threshold: NE
pH: NA
Boiling Point C(F): >393(740)
Drop Point C(F): NE
Flash Point C(F): 224 (435) Estimated for oil, ASTm D-92 (COC)
Flammability (solids): NE
Auto Flammability C(F): NE
Explosive Properties: NA
Oxidizing Properties: NA
Vapor Pressure0mmHg 20 C: <0.1
Vapor Density: <8.0
Evaporation Rate: NE
Relative Density, 15/4 C: NE
Solubility in Water: Negligible
Partition Coefficient: NE
Viscosity At 40C, cSt: 108.0
Viscosity at 100 c, cSt: 12.2
Pour Point C(F): NE
Colatle Organic Compound: NE
Note: Most physical properties for oil component
DMSO Extract, IP-346 (wt%): <3, for mineral oil only
NA=Not applicable, NE=Not established, D=Decomposes
For Further Technical information, contact your marketing representative
10. STABILITY AND REACTIVITY
Stability: Stable Hazardous Polymerization: Will not occur
Conditions to Avoid: Extreme heat Incompatibilities: strong oxidizer
Hazardous Decomposition Products: Product does not decompose at ambient temperatures.
11. TOXICOLOGICAL INFORMATION
Acute Oral LD50:
Oral Toxicity (rats): LD50: > 5g/kg practically non-toxic
Dermal Toxicity (rabbits): LD50: >3.200 g/kg practically non-toxic
Inhalation Toxicity (rats): Not applicable-harmful concentrations of mists and/or vapors are unlikely to be encountered through any
customary or reasonably foreseeable handling, use or misuse of this product.
Eye irritation (rabbits): Practically non-irritating. (draize score: greater than 6 but 15 or less)-Based on testing of similar products
and/or the components
Skin Irritation (rabbits): Practically non-irritating. (Primary irritation index: greater than 0.5 but less than 3).-Based on testing of
similar products and/or the components
MSDS UTG-GEL Page 2
Severely solvent refined and severely hydrotreated mineral base oils have been tested at Mobile Environmental and Health Sciences
laboratory by dermal application to rats 5 days/week for 90 days at doses significantly higher than those expected during normal
industrial exposure. Extensive evaluations including microscopic examination of internal organs and clinical chemistry of body fluids,
showed no adverse effects.
Chronic Toxicology (summary): The base oils in this product are severely solvent refined and/or severely hydrotreated. Chronic
mouse skin painting studies of severely treated oils showed no evidence of carcinogenic effects.
12. ECOLOGICAL INFORMATION
Environmental Fate and Effects:
Ecotoxicity: Not established
Mobility: Not established
Persistence and Degradability: Not established
Bioaccumulative Potential: Not established
13. DISPOSAL CONSIDERATIONS
Waste Disposal: Product is suitable for burning in an enclosed, controlled burner for fuel valve or disposal by supervised incineration.
Such burning may be limited pursuant to the Resource Conservation and Recovery Act. In addition, the product is suitable for
processing by an approved recycling facility or can be disposed of at an appropriate government waste disposal facility. Use of these
methods is subject to user compliance with applicable laws and regulations and consideration of product characteristics at time of
disposal.
RCRA Information: The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40 CFR, Part
261D), nor is it formulated to contain materials which are listed hazardous wasted. It does not exhibit the hazardous characteristics of
ignitability, corrosivity, or reactivity. The unused product is not formulated with substances covered by the Toxicity Characteristic
Leaching Procedure (TCLP). However, used product may be regulated.
14. TRANSPORTATION INFORMATION
USA DOT: Not regulated by USA DOT
RID/ADR: Not regulated by RID/ADR
IMO: Not regulated by IMO
IATA: Not regulated by IATA
15. REGULATORY INFORMATION
US OSHA Hazard Communication Standard: Product assessed in accordance with OSHA 29 CFR 1910.1200 and determined not be
hazardous.
EU Labeling: EU Labeling not required.
Governmental Inventory Status: All components comply with TSCA, EINECS/ELINCS, AICS, DSL, and KECI.
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III: This product contains no 鈥淓xtremely Hazardous
Substances鈥?. SARA (311/312) Reportable Hazard Categories: None
This product contains no chemicals subject to the supplies notification requirements of SARA (313) toxic release program.
This product has been authorized by USDA For use under the following category: This product is acceptable as a lubricant with
incidental food contact (complies with earlier USDA guidelines for H-1 lubricant use).
The following product ingredients are cited on the lists below:
Chemical Name CAS Number List citations
Benzoic Acid, Aluminum Salt 555-32-8 1
Actadecanoic Acid, Aluminum Salt 637-12-7 1, 21
1= ACGIH ALL
21=LA RTK
16. OTHER INFORMATION
Use: Food machinery grease
Note: Products of Exxon Mobile Corporation and its affiliated companies are not formulated to contain PCBS. Health studies have
shown that many hydrocarbons pose potential human health risks which may vary from person to person. Information provided on
this MSDS reflects intended use. This product should not be used for other applications. In any case, the following advice should be
considered:
Injection Injury warning: If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the
wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial
symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly
reduce the ultimate extent of injury.
For Internal Use Only: MHC: 0 0 NA 1* 1*, MPPEC: A, TRN: 642363-00, ELIS: 400228, CMCS97: 974189, REQ: US-Marketing,
Safe Use: G, EHS Approval date: 17 Jan 2002
Legally required information is given in accordance with applicable information given herein is offered in good faith as accurate, but
without guarantee. Conditions of use and suitability of the product for particular uses are beyond our control; all risks of use of the
product are therefore assumed by the user as we expressly disclaim all warranties of every kind and nature, including warranties of
merchantability and fitness for a particular purpose in respect to the use or suitability of the product. Nothing is intended as a
recommendation for uses which infringe valid patents or as extending any license under valid patents. Appropriate warnings and safe
handling procedures should be provided to handlers nd users. Use or retransmission of the information contained herein in any other
format than the format as presented is strictly prohibited. Mobile neither represents nor warrants that the format, content or product
formulas contained in this document comply with the laws of any other country except the United States of America.
|