Material Safety Data Sheet Vitrified Bond Abrasive
Complies with OSHA's Hazard Communication
GOODSON
Standard 29 CFR 1910.1200.
Tools and Supplies for Engine Builders
Airport Industrial Park 鈥? P.O. Box 847 鈥? Winona, MN 55987-0847
Toll-Free 1-800-533-8010 鈥? Local 507-452-1830 鈥? www.goodson.com
DATE OF PREPARATION: June 6, 1997
1. IDENTIFICATION
Description: Vitrified Bond Abrasive
2. COMPOSITION / INFORMATION ON INGREDIENTS
Ingredients Percent CAS #
Aluminum Oxide 90.000-85.000 1344-28-1
Cobalt Aluminate(*) 0.090-0.500 1333-88-6
Amorphous Silica, Fused 10.000-30.000 60676-86-0
Silicon Carbide 90.000-95.000 409-21-2
Sulfur 15.000-40.000 7704-34-9
Other:
*This substance is regulated under Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and the
Canadian National Pollution Reduction Initiative (NPRI). The grinding wheel may be comprised of only some of the above.
3. HAZARDS IDENTIFICATION
Inhalation Acute Exposure Effects: Dust may be slightly irritating to eyes and respiratory tract at high concentrations.
Eye Contact Acute Exposure Effects: Dust may irritate eyes.
Skin Contact Acute Exposure Effects: Some may experience skin irritation from dust.
Ingestion Acute Exposure Effects: No known adverse effects, but ingestion not recommended.
4. FIRST AID MEASURES
Inhalation: Remove to fresh air. If breathing has stopped, give artificial respiration. Get medical attention immediately.
Skin Contact: Wash affected area with soap and water. Obtain medical assistance.
Eye Contact: Wash with large amounts of water. Obtain first aid and medical assistance, if needed.
Ingestion: Call poison control center, hospital emergency room or physician immediately.
5. FIRE FIGHTING MEASURES
Firefighting Procedures: Not applicable
Hazardous Products / Combustion: None
6. ACCIDENTAL RELEASE PROCEDURES
Clean-up: Follow normal clean up procedures.
7. HANDLING AND STORAGE
Handling: Always HANDLE AND STORE wheels in a CAREFUL manner. Always VISUALLY INSPECT all wheels before
mounting. Always CHECK MACHINE SPEED against the established maximum safe operating speed MARKED ON
THE WHEEL. Always CHECK MOUNTING FLANGES for equal and correct diameter. Always USE MOUNTING
BLOTTERS. Always be sure WORK REST is properly adjusted. Always USE A SAFETY GUARD covering at least
one-half of the grinding wheel. Always allow NEWLY MOUNTED WHEELS to run at operating speed, with guard in
place, for at least one minute before grinding. Always TURN OFF COOLANT before stopping wheel to avoid
creating an out-of-balance wheel.
漏 1999 Goodson Shop Supplies
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Ventilation Protection: Handle with adequate ventilation. See OSHA 29 CFR 1910.94 (ventilation) and 29 CFR 1910.1000 (Air
contaminants).
Respiratory Protection: Respirators are required when airborne contaminant levels exceed the TLV(s).
Eye Protection: Always wear safety glasses or some type of eye protection when grinding.
Other Protection: Use of this product may create elevated sound levels. Hearing protection should be worn where required (see
OSHA 29 CFR 1910.134 and other applicable regulations).
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance & Odor: Solid article, orderless
10. STABILITY AND REACTIVITY
Incompatibilities: Avoid acids of all types with a pH<4.0.
Decomposition: In use, dusts are generated. In most cases, the airborne material removed from the workpiece will be significantly
greater than the grinding wheel components. Coolants may produce other decomposition products.
11. TOXICOLOGICAL INFORMATION
Inhalation Chronic Exposure Effects: May affect breathing capacity.
Carcinogenicity: Silica, Amorphous, Fused - IARC-3, NIOSH-X
LD50 / LC50: Values are not appropriate or available.
12. ECOLOGICAL INFORMATION
Chemical Fate: Vitrified products do not appreciably decay.
13. DISPOSAL CONSIDERATIONS
Waste Disposal: Use standard landfill methods consistent with applicable Federal, State, Provincial and local laws. Products
with listed flourides may have slightly soluble fluoride swarf.
14. TRANSPORT INFORMATION
Hazard Class: This product is not hazardous as defined by the Department of Transportation (USA). This product is "Not
Regulated" under the Transportation of Dangerous Goods Act (CAN).
15. REGULATORY INFORMATION
EXPOSURE LIMITS / REGULATORY INFORMATION
Substance Description Units OSHA ACGIH MOL MAK
Aluminum Oxide mg/m3 15.0000 10.0000 10.0000 6.0000
Cobalt Aluminate (*) mg/m3 0.0500 0.0200
Amorphous Silica, Fused mg/m3 0.1000 0.1000 0.3000
Silicon Carbide mg/m3 10.000 10.000 10.0000 4.0000
Sulfur mg/m3
Exposure Limit Descriptions: ACGIH - Am. Conf. Govmnt. Ind. Hyg. MAK - FRG Max. Conc. Values
MOL - Ministry of Labor, CAN OSHA - Occ. Safety & Health Admin.
CA Prop 65: Not applicable
TSCA: Section 8(b) - Inventory Status All components of this product are registered under the regulations of the Toxic Substance
Control Act.
Domestic Substance List: All components of this product are found on the Domestic Substance List.
15. REGULATORY INFORMATION
Disclaimer: The information and recommendations set forth herein are taken from sources believed to be accurate as of the date
hereof; however, Goodson makes no warranty with respect to the accuracy of the information or the suitability of the
recommendations, and assumes no liability to any user thereof.
MSDS Vitrified Abrasive Page 2
|