Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: bmed_mcgill_ca---lepage_polyfilla-cellulose_filler.asp
      01182008                          MATERIAL SAFETY DATA SHEET : 00000115                                         PAGE:1
HENKEL CORPORATION
6685 KENNEDY ROAD, SUITE #1
MISSISSAUGA, ONTARIO CANADA L5T 3A5
(905) 696-2770

PRODUCT : POLYFILLA




SECTION 01: PRODUCT INFORMATION

MANUFACTURER.....................HENKEL CORPORATION
6685 KENNEDY ROAD, SUITE #1
MISSISSAUGA, ONTARIO
CANADA ; L5T 3A5
(905) 696-2770
AFTER HOURS - CANUTEC (613) 996-6666
WHMIS CLASSIFICATION.............NONE
T.D.G. CLASSIFICATION............NOT REGULATED
PRODUCT NAME.....................POLYFILLA
CHEMICAL FAMILY..................CALCIUM SULFATE
MATERIAL USE.....................FINE SURFACE FILLER

SECTION 02: HAZARDOUS INGREDIENTS

HAZARDOUS INGREDIENTS % EXPOSURE LEVELS C.A.S. # LD/50, ROUTE, SPECIES LC/50, ROUTE, SPECIES

Considered non-hazardous as Not available
per WHMIS regulations.

SECTION 03: PHYSICAL DATA

PHYSICAL STATE...................Solid
APPEARANCE & ODOUR...............White powder
ODOUR THRESHOLD (ppm)............Not applicable
VAPOUR PRESSURE (mm Hg)..........Not applicable
VAPOUR DENSITY (AIR=1)...........Not applicable
BY VOLUME
BY WEIGHT
EVAPORATION RATE.................Not applicable
BOILING POINT (deg C)............Not applicable
pH...............................1%. 6.5
SPECIFIC GRAVITY.................Not available
SOLUBILITY IN WATER (% W/W)......Insoluble
COEFFICIENT OF WATER/OIL.........Not available
DISTRIBUTION

SECTION 04: FIRE & EXPLOSION DATA

FLAMMABILITY.....................No
IF YES, UNDER WHICH..............Not applicable
CONDITIONS?
EXTINGUISHING MEDIA..............Water fog
SPECIAL PROCEDURES...............Fire fighters should be equipped with self-contained breathing apparatus
to protect against potentially toxic and irritating fumes.
FLASH POINT (C), METHOD..........Not applicable
AUTO IGNITION TEMPERATURE........Not available
UPPER FLAMMABLE LIMIT (% VOL)....Not applicable
LOWER FLAMMABLE LIMIT (% VOL)....Not applicable
HAZARDOUS COMBUSTION PRODUCTS....None known
EXPLOSION DATA
SENSITIVITY TO STATIC............No
DISCHARGE
SENSITIVITY TO IMPACT......No

SECTION 05: REACTIVITY DATA

CHEMICAL STABILITY:
YES........................Stable under normal temperature and pressure.
NO, WHICH CONDITIONS ?
COMPATIBILITY WITH OTHER
SUBSTANCES:
YES
NO, WHICH ONES?............Strong oxidizing agents
REACTIVITY CONDITIONS ?..........Product is stable; hazardous polymerization will not occur.
HAZARDOUS PRODUCTS OF............No hazardous decomposition products known.
DECOMPOSITION

SECTION 06: TOXICOLOGICAL PROPERTIES

ROUTE OF ENTRY:
SKIN CONTACT...............May cause irritation leading to dermatitis.
01182008 MATERIAL SAFETY DATA SHEET : 00000115 PAGE:2
PRODUCT : POLYFILLA
SECTION 06: TOXICOLOGICAL PROPERTIES

SKIN ABSORPTION............No data
EYE CONTACT................Particulates may scratch eye surfaces/ cause mechanical irritation.
INHALATION.................Not considered a hazard under normal conditions of use. Product readily
produces dust.
INGESTION..................Plaster hardens when wetted and if ingested may result in obstruction.
EFFECTS OF ACUTE EXPOSURE........Refer to route of entry.
EFFECTS OF CHRONIC EXPOSURE......None known
LD 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
LC 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
EXPOSURE LIMIT OF MATERIAL.......Not available
IRRITANCY OF MATERIAL............Refer to route of entry
SENSITIZING CAPABILITY OF........None known
MATERIAL
CARCINOGENICITY OF MATERIAL......No
REPRODUCTIVE EFFECTS.............Not indicated
SYNERGISTIC MATERIALS............Not applicable

SECTION 07: PREVENTATIVE MEASURES

GLOVES/ TYPE...............Gloves are not normally required for foreseeable conditions of use. During
prolonged contact impervious gloves should be worn.
RESPIRATORY/TYPE...........None required under normal use. Use a NIOSH/MSHA approved respirator
whenever dust is generated.
EYE/TYPE...................Safety glasses are optional.
FOOTWEAR/TYPE..............Standard work shoes.
CLOTHING/TYPE..............Standard work clothes.
VENTILATION REQUIREMENTS.........Use adequate general ventilation.
LEAK/SPILL.......................Normal precautions for "nuisance dust" should be observed. Avoid dust
accumulation. Pick up solids and put in a dust bin. Use approved dust
respirator. Use explosion proof vacuum equipment where appropriate.
WASTE DISPOSAL...................In accordance with municipal, provincial and federal regulations.
HANDLING PROCEDURES AND..........Avoid breathing dust.
EQUIPMENT
STORAGE NEEDS....................Avoid high airborne dust concentrations. Prevent accumulations of dust.
Store in a cool and dry place, for product integrity.
SPECIAL SHIPPING INSTRUCTIONS....Not regulated. Protect against physical damage.

SECTION 08: FIRST AID MEASURES

EYE CONTACT......................Immediately flush eyes with large amounts of water until irritation
subsides. If irritation persists, get medical attention.
INGESTION........................Have conscious patient drink several glasses of water, then induce
vomiting by having patient tickle back of throat with finger. Keep airway
clear. Seek medical attention. Never give anything by mouth to an
unconscious person.
INHALATION.......................Remove to fresh air. If symptoms develop, seek medical attention.
SKIN CONTACT.....................Brush off excess dusts. Remove contaminated clothing. Wash affected area
with water and soap. Seek medical attention if irritation occurs or
persists.

SECTION 09: PREPARATION INFORMATION

PREPARED BY:.....................Regulatory Affairs
TELEPHONE NUMBER:................(440) 937-7000
DISCLAIMER2:.....................All information, recommendations, and suggestions appearing herein
concerning our product are based upon tests and data believed to be
reliable. However, it is the user's responsibility to determine the
safety, toxicity, and suitability for his own use of the product described
herein. Since the actual use by others is beyond our control, no
guarantee, express or implied, is made by Henkel Corporation as to
the effects of such use, the results obtained, or the safety and toxicity
of the product nor does Henkel Corporation assume any liability
arising out of use, by others, of the product referred to herein. The
information herein is not to be construed as absolutely complete since
additional information may be necessary or desirable when particular or
exceptional conditions or circumstan ces exist or because of applicable
laws or government regulations.

PREPARATION DATE.................JAN 18/2008

CANUTEC EMERGENCY (613) 996-6666

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
bmed_mcgill_ca---3inoneoil.asp 64742-52-5
bmed_mcgill_ca---3m_scotch-weld_epoxy_potting_compound-adhesive_270_black.asp N/A
bmed_mcgill_ca---3m_super_77_classic_spray_adhesive.asp 110-82-7 107-83-5 115-10-6 75-28-5 74-98-6 96-14-0 75-83-2 79-29-8 110-54-3
bmed_mcgill_ca---4229-liquid.asp 64742-89-8 110-54-3 1330-20-7 67-64-1 100-41-4 112945-52-5 1333-86-4
bmed_mcgill_ca---a9_alum_cutting_fluid.asp 64742-58-1
bmed_mcgill_ca---air-lube-10wnr.asp N/A
bmed_mcgill_ca---alloy_sn-pb_solders-alloys.asp 2005-06-1 7440-31-5 7439-92-1
bmed_mcgill_ca---alvania_grease_rl_2.asp N/A
bmed_mcgill_ca---astro_cut_series_2001_b.asp 64742-52-5 15-20-1
bmed_mcgill_ca---barbasolaloeshavingcream.asp N/A
bmed_mcgill_ca---bernz-o-matic_propane.asp 74-98-6
bmed_mcgill_ca---castrol_stick_wax.asp 8002-74-2 64742-60-5
bmed_mcgill_ca---chemtronics_freez-it.asp 811-97-2
bmed_mcgill_ca---circuitworks_conductive_epoxy_part_a.asp 7440-22-4 025068-38-6 68475-94-5
bmed_mcgill_ca---circuitworks_heat_sink_grease.asp 63148-62-9 1314-13-2 112945-52-5
bmed_mcgill_ca---cool_tool_ii.asp 13-61-4
bmed_mcgill_ca---dow_corning_high_vacuum_grease.asp N/A
bmed_mcgill_ca---epoxy-steel-syringe.asp 140-31-8 112-24-3 90-72-2 1333-86-4
bmed_mcgill_ca---ep_hydraulic_oil_68.asp 64742-54-7 68649-42-3 104-76-7
bmed_mcgill_ca---ethanolmsds.asp N/A
bmed_mcgill_ca---granite_plate_cleaner_2216a51.asp N/A
bmed_mcgill_ca---invoice_flammables_cabinet.asp N/A
bmed_mcgill_ca---ips_weld_on_3.asp 75-09-2 1119-40-0 80-62-6
bmed_mcgill_ca---jbweld_hardener.asp 1317-65-3 7727-43-7 14807-96-6 13463-67-7 1314-98-3 98-00-0 68410-23-1
bmed_mcgill_ca---jbweld_resin.asp 1317-65-3 65997-19-5 25068-38-6 64742-94-5
bmed_mcgill_ca---lepage_contact_cement_cleaner.asp 64742-95-6 9016-45-9
bmed_mcgill_ca---lepage_epoxy_putty.asp 25068-38-6 28064-14-4 32610-77-8 90-72-2
bmed_mcgill_ca---lepage_expoxy_steel.asp 140-31-8 112-24-3 90-72-2 1333-86-4
bmed_mcgill_ca---lepage_polyfilla-cellulose_filler.asp N/A
bmed_mcgill_ca---lepage_poly_instafil.asp N/A
bmed_mcgill_ca---lepage_suregrip_carpenters_glue.asp N/A
bmed_mcgill_ca---loctiter_222ms_threadlocker_low_strength.asp 25852-47-5 9004-96-0 81-07-2 112945-52-5 80-15-9 57-55-6
bmed_mcgill_ca---loctiter_290_threadlocker_wicking_grade.asp 25852-47-5 80-15-9 81-07-2
bmed_mcgill_ca---loctite271.asp 25852-47-5 39382-25-7 81-07-2 80-15-9
bmed_mcgill_ca---loctite609.asp 25852-47-5 868-77-9 68132-02-5 9003-42-3 80-15-9 81-07-2
bmed_mcgill_ca---loctite680.asp 24448-20-2 27813-02-1 39382-25-7 80-15-9 25852-47-5 114-83-0
bmed_mcgill_ca---loctite7471.asp 67-64-1 75-28-5 67-63-0 149-30-4
bmed_mcgill_ca---loctitedegreaser.asp 64742-47-8 5989-27-5
bmed_mcgill_ca---loctite_242_medium_strength_threadlocker_blue_automotive_grade.asp 9004-96-0 81-07-2 112945-52-5 57-55-6 25852-47-5 80-15-9
bmed_mcgill_ca---loctite_401_prism_surface_insensitive_instant_adhesive.asp 7085-85-0
bmed_mcgill_ca---loctite_565_thread_sealant_pst_pipe_sealant_with_ptfe.asp 25852-47-5 68186-73-2 9004-36-8 9002-84-0 13463-67-7 67762-90-7 81-07-2 80-15-9
bmed_mcgill_ca---loctite_620_retaining_compound_slip_fit.asp 24448-20-2 3006-93-7 27813-02-1 80-15-9 112945-52-5 114-83-0
bmed_mcgill_ca---loctite_770_primer_prism.asp 142-82-5
bmed_mcgill_ca---loctite_gasket_eliminatorr_515_flange_sealant.asp 25852-47-5 112945-52-5 79-10-7 80-15-9 81-07-2 114-83-0
bmed_mcgill_ca---loctite_threadlocker_262.asp 25852-47-5 39382-25-7 81-07-2 80-15-9
bmed_mcgill_ca---lubri-delta_acetone.asp 67-64-1
bmed_mcgill_ca---lubriplate.asp 64742-52-5 4485-12-5 68991-19-5 1314-13-2
bmed_mcgill_ca---lucas_oil_red_n_tacky_2.asp N/A
bmed_mcgill_ca---lucas_oil_x-tra_heavy_duty_grease.asp N/A
bmed_mcgill_ca---mastercraft_578016.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC