Monday, May 22, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Restore-A-Gel Copper
MSDS No.: RAG300
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
0
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
3 0
Emergency Contact: CHEMTREC
COR
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
3
0
Last Update: 2-25-2008 Expiration Date:
0
X Liquid Gas Solid
Chemical State:
H
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
7705080 Ferric chloride <40 NE 1 mg/m3 221 F
7631869 Silicon dioxide >2.0
7732185 Water <60 None None 212 F
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
Corrosive. Dangerous if inhaled, ingested, or contacted by skin or eyes. Respiratory and digestive tract irritant. Skin and eye
irritant.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Acute: Skin burns
Chronic: Frequent attacks of bronchial infection
Signs and Symptoms:
Inhalation: Coughing, choking, shortness of breath
Skin: Inflammation, itching, scalling, reddening, occasional blistering
Eyes: Inflammation, redness, watering, itching
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Monday, May 22, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Restore-A-Gel Copper
MSDS No.: RAG300
Emergency and First Aid Procedures:
Inhalation: Remove to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen (To be
administered by qualified medical personnel only!) Get medical attention.
Ingestion: DO NOT induce vomiting. If victim is conscious and alert, give large amounts of water or milk. (Never give anything
by mouth to an unconscious person!) Get medical attention immediately.
Skin: Neutralize exposed skin with a dilute solution of sodium carbonate (baking soda). Flush skin with plenty of soap and water
for at least 15 minutes. Remove contaminated clothing. Seek medical attention.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids. Do not allow victim to
rub or keep eyes closed. DO NOT use an eye ointment. Get medical aid immediately.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Use proper extinguishing media suitable for surrounding fire.
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
Contact with metals may generate flammable hydrogen gas.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear vapor respirator, safety goggles, and rubber gloves. Stop leak if without risk. DO NOT touch spilled material. Dike if
needed. Soak up with inert absorbent material (dry sand or earth recommended; do not use flammable substances such as
sawdust). Neutralize the residue with a dilute solution of sodium carbonate. Dispose according to local, state, and federal
regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in closed container. Avoid incompatible materials. Use only in well-ventilated areas. Avoid contact with clothing, skin, and
eyes. Avoid inhalation and ingestion. Wash thoroughly after handling.
Other Precautions:
DO NOT wear contact lenses while using this product.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, gloves, vapor respirator, protective clothing
Monday, May 22, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Restore-A-Gel Copper
MSDS No.: RAG300
IX. Physical and Chemical Properties:
Boiling Point: 212 F Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): 17.535
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): 0.62
Solubility In Water: Easily soluble Appearance and Odor:
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Metals, nylon
Decomposition/By Products:
Flammable hydrogen gas, soluble iron salts
Hazardous Polymerization:
Has not been reported.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in closed container. Avoid incompatible materials. Avoid contact with clothing, skin, and eyes. Avoid inhalation and ingestion.
Wash thoroughly after handling.
IATA
Shipping name: Ferric chloride solution
Hazard class: 8
UN no.: 2582
Packing group: III
Corrosive!
XV. Regulatory Information:
All ingredients are listed on the TSCA inventory.
Monday, May 22, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Restore-A-Gel Copper
MSDS No.: RAG300
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|