Wednesday, May 24, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Catalyst
MSDS No.: TM1
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
2 1
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
2
1
Last Update: 2-27-2008 Expiration Date:
1
X Liquid Gas Solid
Chemical State:
H
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
149575 Ethylhexanoic acid 3 NE NE
301100 Stannous octoate 97 2 mg/m3 2 mg/m3 287 F
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
May be harmful if swallowed or absorbed through the skin. May cause respiratory and digestive tract irritation with possible
burns. May cause severe skin and eye irritation with possible burns.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Chronic: Allergic skin reaction
Signs and Symptoms:
Ingestion: Burns to the mouth, throat, and digestive tract
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory, digestive diseases
Emergency and First Aid Procedures:
Wednesday, May 24, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Catalyst
MSDS No.: TM1
Inhalation: Remove to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen (To be
administered by qualified medical personnel only!) Get medical attention immediately.
Ingestion: DO NOT induce vomiting. If victim is conscious and alert, give water to drink. (Never give anything by mouth to an
unconscious person!) Get medical attention immediately.
Skin: Flush skin with plenty of soap and water for at least 15 minutes. Remove contaminated clothing. Destroy contaminated
shoes. Seek medical attention immediately.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids. Do not allow victim to
rub or keep eyes closed. Get medical aid immediately.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: >287 F Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Water spray, carbon dioxide, dry chemical
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing. Firefighting equipment should be thoroughly decontaminated
after use.
Unusual Fire and Explosion:
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear vapor respirator, safety goggles, and rubber gloves. Stop leak, if possible. Remove sources of ignition (i.e. open flames,
sparks). Dike area. Soak up with inert absorbent material (do not use flammable substances such as sawdust). Avoid generation
of vapors. Ventilate and decontaminate spill site after collection. Dispose according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in closed container. Prevent container damage and spillage. Avoid direct sunlight. Avoid incompatible materials. Use only
in well-ventilated areas. Avoid contact with skin, eyes, and clothing. Avoid ingestion and inhalation. Wash thoroughly after
handling.
Other Precautions:
DO NOT wear contact lenses while using this product.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, gloves, vapor respirator, protective clothing
Wednesday, May 24, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Catalyst
MSDS No.: TM1
IX. Physical and Chemical Properties:
Boiling Point: NE Melting Point: <113 F
Evaporation Rate (Butyl Acetate = 1): N/A Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): NE
Solubility In Water: Insoluble Appearance and Odor:
Other Information: * Appearance & Odor: Colorless to pale yellow liquid with a characteristic odor
X. Stability and Reactivity:
Stability:
Stable under normal and anticipated storage and handling conditions.
Incompatibility (Materials to Avoid):
Oxidizers, ignition sources (heat, open flame, spark), sunlight
Decomposition/By Products:
Carbon monoxide & dioxide, tin oxides, inorganic tin salts
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in closed container. Prevent container damage and spillage. Avoid direct sunlight. Avoid incompatible materials. Avoid
contact with skin, eyes, and clothing. Avoid ingestion and inhalation. Wash thoroughly after handling.
XV. Regulatory Information:
All ingredients are listed on the TSCA inventory.
All ingredients are hazardous by definition of OSHA Hazard Communication Standard (29 CFR 1910.1200).
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Wednesday, May 24, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Catalyst
MSDS No.: TM1
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|