Tuesday, May 23, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Small Particle Reagent--Dark
MSDS No.: SPR100
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 1
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
1
Last Update: 2-27-2008 Expiration Date:
1
X Liquid Gas Solid
Chemical State:
J
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
1317335 Molybdenum sulfide Trace 5 mg/m3 5 mg/m3 2,375 F
139888 Niaproof 4 0.5 NE NE
7732185 Water 99.5 None None 212 F
III. Hazardous Identification:
Hazard Category:
X Acute Chronic Fire Pressure Reactive
Hazardous Identification Information:
Readily absorbed by skin. Respiratory irritant. May irritate and dry skin. May cause dermatitis. May irritate and burn eyes.
The chemical, physical, and toxicological properties of tergitol have not been thoroughly investigated.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Signs and Symptoms:
Inhalation: Coughing, sneezing, difficulty breathing
Skin: Redness, inflammation
Eyes: Redness, burning, inflammation, watering
Medical Conditions Generally Aggravated by Exposure:
Skin, lung, kidney, liver diseases
Tuesday, May 23, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Small Particle Reagent--Dark
MSDS No.: SPR100
Emergency and First Aid Procedures:
Inhalation: Remove to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen (To be
administered by qualified medical personnel only!) Get medical attention.
Ingestion: DO NOT induce vomiting. If victim is conscious and alert, give 2-4 cups of milk or water. (Never give anything by
mouth to an unconscious person!) Get medical attention immediately.
Skin: Flush skin with plenty of soap and water for at least 15 minutes. Remove contaminated clothing. Seek medical attention if
condition warrants.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids. Do not allow victim to
rub or keep eyes closed. Get medical aid immediately.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Dry chemical, carbon dioxide, alcohol foam
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
Sulfides are moderate fire hazards when exposed to flame or spontaneous chemical reaction. Many sulfides ignite easily in air and
at room temperature.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear vapor respirator, safety goggles, and rubber gloves. Remove sources of ignition (i.e. open flames, sparks). Dike if needed.
Soak up with absorbent material (sand or vermiculite recommended; do not use flammable substances such as sawdust).
Ventilate and wash spill site after collection. Dispose according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in tightly closed container. Keep cool and dry. Avoid incompatible materials. Use only in well-ventilated areas. Avoid
inhalation. Avoid contact with skin, eyes, and clothing. Avoid prolonged or repeated exposure. Wash thoroughly after handling.
Other Precautions:
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles; neoprene, plastic, or rubber gloves; dust & vapor respirator; protective clothing
Tuesday, May 23, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Small Particle Reagent--Dark
MSDS No.: SPR100
IX. Physical and Chemical Properties:
Boiling Point: ~212 F Melting Point: ~32 F
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): NE
Solubility In Water: Partial Appearance and Odor:
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Strong oxidizing agents, strong acids & bases, acid chlorides & anhydrides, steel, potassium nitrate, hydrogen peroxide
Decomposition/By Products:
Sulfur oxides, hydrogen sulfide, carbon monoxide & dioxide, molybdenum, molybdenum oxides, sulfur
Hazardous Polymerization:
Does not occur.
XI. Toxicological Information:
The toxicological properties of tergitol have not been thoroughly investigated.
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life. Material is not readily biodegradable.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in tightly closed container. Keep cool and dry. Avoid incompatible materials. Avoid inhalation. Avoid contact with skin, eyes,
and clothing. Avoid prolonged or repeated exposure. Wash thoroughly after handling.
XV. Regulatory Information:
Tergitol is listed on the TSCA inventory.
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Tuesday, May 23, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Small Particle Reagent--Dark
MSDS No.: SPR100
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|