Tuesday, May 23, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Cyanowand Cartridge
MSDS No.: SCW200
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
2
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
2 1
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
2
2
Last Update: 2-25-2008 Expiration Date:
1
X
Liquid Gas Solid
Chemical State:
H
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
7085850 Ethyl cyanoacrylate 30-40 4 ppm 4 ppm 2 ppm
9011147 Poly(methyl methacrylate) 1-4 NE NE
0 Steel wool 60-70 NE NE
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
Respiratory tract irritant. Skin irritant. Bonds skin rapidly and strongly. May cause skin burns. Eye irritant.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Respiratory tract irritant. Skin irritant. Bonds skin rapidly and strongly. May cause skin burns. Eye irritant.
Signs and Symptoms:
Prolonged and repeated overexposure to vapors may produce symptoms of non-allergic asthma in sensitive individuals.
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Emergency and First Aid Procedures:
Tuesday, May 23, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Cyanowand Cartridge
MSDS No.: SCW200
Inhalation: Remove to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen (To be
administered by qualified medical personnel only!) Get medical attention.
Ingestion: Ingestion is not likely. See supplemental page.
Skin: Soak in warm water. See supplemental page.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids. Do not allow victim to
rub or keep eyes closed. Get medical aid immediately. See supplemental page.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: 150-200 F Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Carbon dioxide, foam, dry chemical
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Flood with water to polymerize. Remove all ignition sources (heat, open flame, spark). Soak up with inert absorbent material (do
not use flammable substances such as sawdust). Dispose according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in closed container. Store at or below 75 F. Avoid incompatible materials. Use only in well-ventilated areas. Avoid contact
with skin and eyes. Avoid breathing vapors. Wash thoroughly after handling.
Other Precautions:
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, vapor respirator, nitrile or polyethylene gloves and aprons (no cotton)
Tuesday, May 23, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Cyanowand Cartridge
MSDS No.: SCW200
IX. Physical and Chemical Properties:
Boiling Point: >300 F Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): <0.2
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): ~3
Solubility In Water: Polymerized by water Appearance and Odor:
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Water, alcohols, amines, alkalies, ignition sources (heat, open flame, spark)
Decomposition/By Products:
Irritating organic fragments
Hazardous Polymerization:
Does not occur.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways.
XIII. Disposal Considerations:
Polymerize as above. Incinerate according to local, state, and federal regulations.
XIV. Transport Information:
Keep in closed container. Transport at or below 75 F. Avoid incompatible materials. Avoid contact with skin and eyes. Avoid
breathing vapors. Wash thoroughly after handling.
IATA
Proper shipping name: Unrestricted (<1 pint) / Other regulated substances (>1 pint)
Class or division: Unrestricted (<1 pint) / Class 9 (>1 pint)
UN or ID no.: None (<1 pint) / ID 8027 (>1 pint)
XV. Regulatory Information:
Tuesday, May 23, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Cyanowand Cartridge
MSDS No.: SCW200
XVI. Other Information:
This MSDS may also be used for catalogue numbers SCW300, SCW400, and SCW4001.
See attached supplemental page for more information on treatment for adhesion of human skin by cyanoacrylate adhesives.
Using this product under normal, properly instructed procedures should not be hazardous.
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|