Tuesday, May 23, 2006
Page 1 of 3
MSDS - Material Safety Data Sheet
Product Name: Modeling Clay
MSDS No.: STM1003
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 0
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
1
Last Update: 2-27-2008 Expiration Date:
0
X
Liquid Gas Solid
Chemical State:
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
1332587 Kaolin 57.70 10 mg/m3 2 mg/m3
III. Hazardous Identification:
Hazard Category:
X Acute Chronic Fire Pressure Reactive
Hazardous Identification Information:
Eye irritant.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Signs and Symptoms:
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Emergency and First Aid Procedures:
Eyes: Rinse with plenty of water for 15 minutes and seek medical attention.
Contact a Poison Control Center.
Other Health Warnings:
Tuesday, May 23, 2006
Page 2 of 3
MSDS - Material Safety Data Sheet
Product Name: Modeling Clay
MSDS No.: STM1003
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Use proper extinguishing media suitable for surrounding fire.
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Clean with paper towel and wet sponge. Wash spill area with soap and water.
VII. Handling and Storage:
Precautions to be Taken:
Keep in closed container. Uncovered product will dry out. Avoid incompatible materials. Use only in well-ventilated areas. Wash
thoroughly after handling.
Other Precautions:
Pigments used in this product are formed at high temperature calcination. Frits are produced from the chemical reactions which
occur during high temperature smelting of various raw materials to form a molten glass. This glass is rapidly cooled to produce
granules or flakes. These may subsequently be milled to produce powdered frit. Frit (glass) is an essentially insoluble substance.
Therefore, pigments/frits do not necessarily have any of the properties of the components oxides or metals.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Not needed
IX. Physical and Chemical Properties:
Boiling Point: NE Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): N/A Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): >1
Solubility In Water: Yes Appearance and Odor:
Other Information:
Tuesday, May 23, 2006
Page 3 of 3
MSDS - Material Safety Data Sheet
Product Name: Modeling Clay
MSDS No.: STM1003
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Decomposition/By Products:
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in closed container. Uncovered product will dry out. Avoid incompatible materials. Wash thoroughly after handling.
XV. Regulatory Information:
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|