Wednesday, November 17, 2004
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Release Agent
MSDS No.: SRA-10
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
4
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 0
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Premier Crown Tech Support
Information Telephone Number: 919-554-2244
1
4
Last Update: 2-27-2008 Expiration Date:
0
X Liquid Gas Solid
Chemical State:
B
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
63148629 Dimethyl polysiloxane
142825 Heptane
68476-85-7 Liquified Petroleum Gas 1000ppm 1000ppm
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic X Fire X Pressure Reactive
Hazardous Identification Information:
CONTENTS EXTREMELY FLAMMABLE AND UNDER PRESSURE. AVOID CONTACT WITH SKIN AND EYES. VAPOR
HARMFUL, INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING AND INHALING THE CONTENTS MAY BE
HARMFUL OR FATAL.
IV. First Aid Measures:
Route(s) of Entry:
INGESTION: Unlikely due to being an aerosol. Should actual ingestion occur, DO NOT INDUCE VOMITING! Drink a glass of milk
or water to dilute. Call a physician or poison control immediately. Never give anything by mouth to an unconscious person.
EYE: Immediately flush with plenty of clear water for at least 15 minutes. Make sure to flush under the eyelids. Consult a
physician for definitive treatment.
SKIN: Remove with soap and water. Continue flushing with water for several minutes. Use skin cream to counter resulting
dryness. Consult a physician if irritation continues.
INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Seek medical
attention if symptons persist or the person is unconscious.
Health Hazards (Acute and Chronic):
Acute Oral LD50: No data available.
Acute Dermal LD50: No data available.
Acute Inhalation LC50: Liquified petroleum gas
Wednesday, November 17, 2004
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Release Agent
MSDS No.: SRA-10
Signs and Symptoms:
SKIN: Defatting and drying of the skin, skin irritation.
EYES: Liquid and vapors may cause redness, burning, tearing, swelling and/or pain.
INGESTION: Irritation to the membranes of the mouth, throat and gastrointestinal tract, resulting in vomiting or cramps.
INHALATION: May cause irritation of the respiratory tract, or acute nervous system depression characterized by headache,
dizziness, staggering gait, or confusion.
Medical Conditions Generally Aggravated by Exposure:
Skin contact may aggravate existing dermatitus. Other conditions unknown.
Emergency and First Aid Procedures:
See above Routes of Entry.
Other Health Warnings:
None of the ingredients in this product are listed with OSHA, IARC or NTP as being carcinogenic.
V. Fire Fighting Measures:
Flash Point: <0潞 F Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Use NFPA Class B extinguishers (CO2, dry chemical or aqueous foam)
Special Fire Fighting Procedures:
Use water spray to cool fire exposed aerosol containers because containers may rupture violently from heat-developed pressure.
Unusual Fire and Explosion:
Contents under pressure. When liquid or vapor comes into contact with flames or red hot metal, products of combustion will be
created. Firefighters should wear self-contained breathing apparatus.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
CONTAINMENT PROCEDURES: Product is an aerosol so spill is unlikely. In case of rupture, released content should be
contained as any other solvent spill.
SPILL CLEANUP: In case of actual rupture, avoid breathing vapors and ventilate area well. Remove all sources of ignition and use
non-sparking equipment. Soak up material with inert absorbent material and place in safety containers for proper disposal.
SPECIAL INSTRUCTIONS: Aerosol products present a limited hazard and will not spill or leak unless ruptured. In case of rupture,
the container will evacuate rapidly. The area should be ventilated immediately and continuous ventilation provided until all fumes
and vapors have been removed. AEROSOL CANS SHOULD NEVER BE INCINERATED OR BURNED."Empty" containers may
contain product residue and may be dangerous. Empty containers should be completely drained and bunged and then disposed of
according to local, state and federal regulation
REPORTING REQUIREMENTS: If a large spill occurs, the reporting requirements of the EPA and other state, local and federal
agencies should be observed.
VII. Handling and Storage:
Precautions to be Taken:
Avoid prolonged or repeated skin contact. Avoid breathing vapors. Store in area below 120潞 F. Do not incinerate or burn
containers. Assure container is in a secure place to prevent knocking over and accidental rupture. Always replace the overcap
when not in use.
Wednesday, November 17, 2004
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Release Agent
MSDS No.: SRA-10
Other Precautions:
For storage of pallet quantities, compliance with ANSI/NFPA 30B is recommended.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
General ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. Local
exhaust or an enclosed handling system may be needed to control air contamination below that of the lowest TLV/PEL rated
ingredient in Section 2.
Personal Protective Equipment:
EYE PROTECTION: Safety glasses with side protection or safety goggles are recommended as a minimum when using this
product. Where eye contact could occur, use chemical, splash-proof goggles.
SKIN PROTECTION: For brief contact, no precautious other than clean, body covering clothing should be needed. Should
prolonged or repeated contact be likely, use protective clothing like Sol-Vex gloves or other clothing impervious to ingredients listed
in Section 2.
RESPIRATORY PROTECTION: Use an appropriate NIOSH-approved respirator for organic vapor.
IX. Physical and Chemical Properties:
Boiling Point: <0潞 F Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): No Data
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): Above 1.0
Solubility In Water: Negligible Appearance and Odor: Clear colorless liquid, with paint-like odor.
Other Information:
X. Stability and Reactivity:
Stability:
Normally stable.
Incompatibility (Materials to Avoid):
Heat, sparks, flame, hot metal.
Decomposition/By Products:
Oxides of carbon.
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
Acute Inhalation: LC50: Liquified Petroleul Gas
XII. Ecological Information:
This product has not been tested for environmental effects.
Wednesday, November 17, 2004
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Silicone Rubber Release Agent
MSDS No.: SRA-10
XIII. Disposal Considerations:
An aerosol container that does not contain a significant amount of liquid would meet the definition of scrap metal (40 CFR 261.11(c)
(6), and would be exempt from RCRA regulations if it is to be recycled. If the container is not to be recycled, they must be managed
under all applicable RCRA and state regulations.
"Empty" containers may contain product residue and may be dangerous. Empty containers should be completely drained and
bunged and then disposed of according to local, state and federal regulations.
XIV. Transport Information:
IATA
Shipping name: Aerosols, flammable
Hazard class: 2.1
UN no.: 1950
Flammable gas!
XV. Regulatory Information:
Toxic Substances Control Act: All of the ingredients are on the TSCA inventory.
CAA, CWA: Not listed.
Canadian Workplace Hazardous Materials Information System (WHMIS): Heptane and LPG are listed.
XVI. Other Information:
Keep in tightly closed container. Transport at temperatures below 120 F. Keep cool and dry. Avoid direct sunlight. Avoid all ignition
sources (heat, open flame, spark). Avoid incompatible materials. Avoid contact with skin, eyes and clothing. Avoid ingestion and
inhalation. Wash thoroughly after handling.
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
Using this product under normal, properly instructed procedures should not be hazardous.
|