ANCHOR-WELD CA1
DIRECT STICK CARPET ADHESIVE
鈥? Colour: Off White
Low Odour / Water Based
Viscosity: Thick paste
鈥? High Initial Grab
Solids: 59%
鈥? High Early Bond Strength
PACKAGING
DESCRIPTION
Available in 20L pails
Anchor-Weld CA1 is a water based trowelable adhesive for
Direct Stick bonding of carpet. It displays high initial grab and
CLEAN UP
good early bond strength.
Tools should be washed with water whilst adhesive is still wet.
PURPOSE FOR USE
SAFETY PRECAUTIONS
Anchor-Weld CA1 bonds jute, latex, Action Bac魏, woven, foam
Anchor-Weld CA1 is not dangerous to health or flammable. A
back and needle punch carpet to concrete and wooden
Material Safety Data Sheet is available on request.
subfloors.
STORAGE & SHELF LIFE
LIMITATIONS
Do not allow to freeze, store out of direct sunlight, keep in
Because of the wide range of surfaces and floorings, a test of
original containers tightly closed when not in use. Shelf life:
any new combination should be conducted before using.
minimum 12 months from date of manufacture if stored under
Not recommended for: Oily timber, Oil tempered particleboard,
cover between 5掳C and 30掳C.
External use.
TECHNICAL SUPPORT
PREPARATION
Anchor-Weld Technical Services are available to pre-test any
Ensure the surface is even, clean, dry and free from oil, dust or
samples of substrate where the specifier / applicator may believe
flaking paint. A very porous or highly absorbent surface (eg.
doubts on application suitability exists.
concrete or wood) should be primed first with Anchor-Weld PR1
The tests will aid in determining the proper surface preparation
Primer.
method. Following this procedure will remove many of the
Ensure concrete subfloors are free from hydrostatic pressure,
unknown variables that affect field success. Please contact your
and test moisture content prior to priming or laying floor covering.
Anchor-Weld Distributor for further details.
APPLICATION & COVERAGE RATE
WARRANTY
Refer to refer to AS/NZS2455.1-1995 A Textile Floor Coverings -
Your purchase of this product is subject to Anchor-Weld鈥檚
Installation Practice, Part 1: General for further preparation and
standard terms and conditions of sale. The representation and
laying details.
recommendations regarding the products are based on tests
Do not apply adhesive if temperature is below 10掳C.
which we believe to be reliable. However, no guarantee of their
Spread CA1 evenly with a 螒V鈮? notch trowel.
accuracy can be made because of the great range of field
conditions and variations encountered in raw materials,
Smooth backed carpets:
manufacturing equipment and methods.
2
Trowel: 2.4 mm V-notch (coverage approx. 3 m /L)
Ideal Open time: 20 minutes
Thus, the products are sold with a limited warranty only, and on
Coarse backed carpets:
the condition that purchasers will make their own tests to
2
Trowel: 3.2 mm V-notch (coverage approx. 2 m /L)
determine the suitability of the product for their particular
Ideal Open time: 30 minutes
purposes. Under no circumstances will Anchor-Weld be liable to
anyone except for replacement of the products or refund of the
The adhesive must be allowed to tack up and develop some
purchase price.
grab before laying in the floor covering. This can be assessed by
lightly pressing your finger onto the surface of the adhesive then
All other warranties whether express or implied, including without
pulling away - tack up is observed when the adhesive appears
limitation, any warranty of merchantability of fitness of purpose
stringy / leggy.
are expressly disclaimed unless prohibited by law or given in
Ensure adhesive transfer occurs into the carpet backing.
writing by Anchor-Weld for a specific project.
Note: Open time is influenced by substrate porosity and
ALL SALES ARE EXPRESSLY LIMITED TO THE TERMS AND
atmospheric conditions (ie. Temperature, humidity, air
CONDITIONS OF SALE OF ANCHOR-WELD AUSTRALIA.
movement).
Roll the installation using a 25 - 35 kg roller in both directions
Anchor-Weld CA1
immediately after laying. Then re-roll after 20 minutes.
ITEM NO. STOCK SIZE
Avoid heavy traffic for 24 hours after installation.
511765 Anchor-Weld CA1 20L
TYPICAL TECHNICAL DATA
Base: Latex
|