MATERIAL SAFETY DATA SHEET
HMIS CODES: H F R P
KEY8883
PRODUCT NAME: KEY 3-N-1 DTM/PRIMER/SEALER ACTIVATOR 2 2 1 G
PRODUCT CODE: KEY8883
SECTION I - HAZARDOUS INGREDIENTS/SARA III INFORMATION
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
* Toluene 108-88-3 38 20 C 30 鈥? 35
OSHA TWA 100 ppm
Methoxy-2-Propyl Acetate 108-65-6 3.7 20 C 25 鈥? 30
None established by OSHA or ACGIH as of 8/98
n-Butyl Acetate 123-86-4 7.8 20 C 10 鈥? 15
OSHA PEL 150 ppm (TWA)/ 200 ppm (STEL)
ACGIH TLV 150 ppm (TWA)/ 200 ppm (STEL)
* Xylene, mixed isomers 1330-20-7 38 20 C 5 鈥? 10
OSHA TWA 100 ppm, STEL 150 ppm
* Ethylbenzene 100-41-4 38 20 C <1
OSHA TWA 100 ppm, STEL 125 ppm
* 1,6-Hexamethylene Diisocyanate 822-06-0 < .01 20 C <1
ACGIH TWA .005 ppm
Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. WARNING:
DETECTABLE AMOUNTS OF A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND/OR
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM MAY BE PRESENT IN THIS PRODUCT.
SECTION II - PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING RANGE: 150 F - 282 F SPECIFIC GRAVITY (H20=1): 0.95
VAPOR DENSITY: Heavier than air EVAPORATION RATE: Slower than n-Butyl Acetate
COATING V.O.C.: 5.93 lb/gal MATERIAL V.O.C.: 5.93 lb/gal
SOLUBILITY IN WATER: Non soluble APPEARANCE AND ODOR: Viscous liquid with ketone odor.
SECTION III - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 45 F METHOD USED: TCC
LOWER: 1.0 UPPER: 7.6
FLAMMABLE LIMITS IN AIR BY VOLUME:
EXTINGUISHING MEDIA: FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL, AND WATER FOG.
REV. 12\02 1
Document#: MS-????
SPECIAL FIREFIGHTING PROCEDURES: Respiratory equipment should be worn to avoid inhalation of concentrated
vapors. Water should not be used except as fog to keep nearby containers cool.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Handle as flammable liquid. Vapors form explosive mixture in air
between upper and lower explosive limits which can be ignited by many sources such as pilot lights, open flames,
electrical motors and switches.
SECTION IV - REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive heat, poor ventilation, corrosive atmospheres, excessive age.
INCOMPATIBILITY (Materials to avoid): Alkaline materials, strong acids, and oxidizing agents.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: Carbon monoxide, carbon dioxide, oxides of nitrogen.
HAZARDOUS POLYMERIZATION: Will Not Occur.
SECTION V - HEALTH HAZARD DATA
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Inhalation: Dizziness, breathing difficulty, headache
& loss of coordination.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Eye contact: severe irritation, tearing,
redness and blurred vision.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Skin contact: Can dry and defat skin causing
cracks, irritation, and dermatitis.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Ingestion: Can cause gastrointestinal irritation,
vomiting, nausea, and diarrhea.
HEALTH HAZARDS (ACUTE AND CHRONIC): ACUTE: Inhalation - Dizziness, breathing difficulty, headaches, & loss
of coordination. Eye Contact - Severe irritation, tearing, redness, and blurred vision. Skin Contact - Can dry and defat
skin causing cracks, irritation, and dermatitis. Ingestion - Can cause gastrointestinal irritation, vomiting, nausea, and
diarrhea. CHRONIC: Repeated and prolonged overexposure to solvents may lead to permanent brain and nervous
system damage.
CARCINOGENICITY: NTP CARCINOGEN: NO IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Anesthesia, respiratory tract irritation,
dermatitis, nausea, and vomiting.
EMERGENCY AND FIRST AID PROCEDURES: Inhalation Overexposure - Move person to fresh air. If breathing
stops, apply artificial respiration and seek immediate medical attention. Eye Contact - Flush with large quantities of
water for 15 minutes. Skin Contact - Wash thoroughly with soap and water, and see a doctor. Ingestion - DO NOT
induce vomiting, can cause chemical pneumonitis and pulmonary edema. Contact physician immediately.
SECTION VI - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate ignition sources, provide good
ventilation, dike spill area and add absorbent earth or sawdust to spilled liquid.
REV. 12\02 2
Document#: MS-????
WASTE DISPOSAL METHOD: Collect absorbent/spilled liquid mixture into metal container; cover and seal container.
Consult local, state, and federal hazardous waste regulations before disposing into approved hazardous waste landfill.
Obey relevant laws.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Use non-sparking utensils when handling this material.
Avoid hot metal surface. Use in cool, well-ventilated areas. Keep containers closed when not in use. Keep away from
excessive heat and open flames.
OTHER PRECAUTIONS: Smoking in areas where this material is used should be strictly prohibited. Tools used with this
material should be made from aluminum, brass, or copper. Plastic utensils should not be used.
SECTION VII - CONTROL MEASURES
RESPIRATORY PROTECTION: When spraying this material use a fresh-air supplying respirator or a self-contained
breathing apparatus.
VENTILATION: General mechanical ventilation or local exhaust should be suitable to keep vapor concentrations below
TLV. Ventilation equipment must be explosion proof.
PROTECTIVE GLOVES: Impermeable chemical handling gloves for skin protection.
EYE PROTECTION: Use chemical safety glasses, goggles, and face shields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Use impermeable aprons and protective clothing whenever
possible to prevent skin contact. The use of head caps whenever possible is strongly recommended.
WORK/HYGIENIC PRACTICES: Eye washes and safety showers in the workplace are recommended.
SECTION VIII - DISCLAIMER
To the best of our knowledge, the information contained herein is accurate, obtained from sources believed by
Cumberland Products Inc. to be accurate.
REV. 12\02 3
Document#: MS-????
|