MATERIAL SAFETY DATA SHEET
Page 1 of 5
Sika Boom
HMIS
HEALTH 1
FLAMMABILITY 1
REACTIVITY 1
C
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
Sika Corporation None Given
201 Polito Ave
Lyndhurst, NJ 07071
Company Contact: EHS Department
Telephone Number: 201-933-8800
FAX Number: 201-933-9379
Web Site: www.sikausa.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
CHEMTREC: 800-424-9300 None Given
INTERNATIONAL: 703-527-3887
Issue Date: 07/08/2003
Product Name: Sika Boom
CAS Number: Not Established
Chemical Family: Urethane Foam
MSDS Number: 2697
Product Code: C439012
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
FLUOROCARBON (NON-FLAMMABLE COMPRESSED GAS, HCFC) Not Establis
HIGHER OLIGOMERS OF MDI (POLYMERIC MDI) 9016-87-9
METHYLENE BISPHENYL ISOCYANATE 101-68-8
EMERGENCY OVERVIEW
Physical Hazard
Since the containers are pressurized, storage temperature should not exceed 120F (49C) in order to avoid
excessive pressure build-up and possible container rupture. Also, the foam has strong adhesive-like
characteristics and will adhere to skin and other surfaces. If accidental foam contact occurs, follow the
appropriate first-aid procedure described in this MSDS.
3. Hazards Identification
Eye Hazards
May cause eye irritation. Foam contact can cause physical damage due to adhesive character.
MATERIAL SAFETY DATA SHEET Page 2 of 5
Sika Boom
3. Hazards Identification - Continued
Skin Hazards
May cause localized irritation, reddening or swelling. Prolonged or repeated exposure may lead to sensitization
and/or dermatitis.
Ingestion Hazards
May cause irritation of mucous membranes in the mouth and digestive tract.
Inhalation Hazards
May irritate mucus membranes with tightness in chest, coughing, or allergic asthma-like sensitivity. Extensive
over exposure can lead to respiratory symptoms like bronchitis and pulmonary edema. These effects are usually
reversible.
Over exposure to fluorocarbon may cause lightheadedness, headaches, or lethargy. Persons with cardiac
arrhythmia may be at increased risk in severe exposure.
4. First Aid Measures
Eye
Flush with clean water for atleast 15 minutes and obtain medical attention.
Skin
Use a rag to remove excess foam from skin and remove contaminated clothing. Cured foam may be physically
removed by persistent washing with soap and water. If irritation develops, use mild skin cream. If irritation
persists, obtain medical attention.
Ingestion
Do not induce vomiting. Drink 1-2 glasses of water or milk. Consult a physician. Do not give anything orally to an
unconscious person.
Inhalation
If breathing difficulty is experienced, move to an area free of exposure. Provide fresh air, If necessary, provide
oxygen or artificial respiration by trained personnel and obtain medical attention.
5. Fire Fighting Measures
Flash Point: 800 掳F 426.6 掳C
Fire And Explosion Hazards
High temperatures will raise the pressure in the containers, which may lead to rupturing.
Extinguishing Media
Dry chemical, carbon dioxide, halon 1211, chemical foam, or water spray if used in large quantities (water
contamination will produce carbon dioxide).
Fire Fighting Instructions
Wear self-contained breathing apparatus to protect against toxic decomposition by-products, including CO, CO2,
NO, and traces of HCN aor HCL. Cured foam is organic and, tehrefore, will burn in the presence of sufficient heat,
oxygen and ignition source.
6. Accidental Release Measures
Provide adequate ventilation and wear recommended protective clothing (gloves, safety goggles, long sleeve work
clothes). Uncured foam is very sticky, so carefully remove the bulk of the foam by scraping it up and then immediately
remove residue with a rag and solvent. Once foam has cured, it can only be removed physically by scraping, buffing,
etc. Dispose as plastic waste (foam plastic) in accordance with all applicable guidelines and regulations.
Before disposing of containers, relieve container of any remaining foam and pressure. Allow foam to fully cure before
disposing.
MATERIAL SAFETY DATA SHEET Page 3 of 5
Sika Boom
7. Handling And Storage
Handling And Storage Precautions
Store in a cool, dry place. Ideal storage temperature is 60F to 80F (15.5C to 26.6C). Storage above 90F (32.2C)
will shorten the shelf life. Protect containers from physical abuse. Protect unused product from freezing.
8. Exposure Controls/Personal Protection
Engineering Controls
Use with adequate general and local exhaust ventilation.
Eye/Face Protection
Safety glasses with side shields or goggles recommended.
Skin Protection
Chemical-resistant gloves. Lab coat or other work clothing to prevent skin exposure. Launder before reuse.
Respiratory Protection
A respirator protection program that meets 29 CFR 1910.134 requirement must be followed whenever workplace
conditions warrant a respirator's use. In areas where the Permissible Exposure Limits are exceeded, use a
properly fitted NIOSH-approved respirator.
Ingredient(s) - Exposure Limits
FLUOROCARBON (NON-FLAMMABLE COMPRESSED GAS, HCFC)
OSHA - 1,000 ppm TWA
ACGIH - 1,000 TWA
METHYLENE BISPHENYL ISOCYANATE
OSHA - 0.020 ppm ceiling
OSHA - 0.200 mg/m3 ceiling
ACGIH - 0.005 ppm TWA
ACGIH - 0.051 mg/m3 TWA
9. Physical And Chemical Properties
Odor
Slight fluorocarbon odor during curing stage.
Chemical Type: Mixture
Physical State: Liquid
Specific Gravity: 1.2
Physical Appearance: Viscous liquid which foams upon release from container as an off-white to yellowish froth.
Boiling Point: Fluorocarbon component (Non-Flammable Gas) boils at less then 0F (-17.7C). Other components boil at
temperature greater than 200F (93.3C).
Vapor Pressure: Contents under pressure have a vapor pressure greater than 50 psig (345 Kpa). After release from
container, vapor pressure is very low (not determined).
Solubility in Water: Insoluble, reacts slowly with water during cure; liberating traces of CO2.
Explosive Data: Contents are not known to be sensitive to mechanical impact or static discharge.
10. Stability And Reactivity
Stability: Stable under normal storage and handling and conditions
Hazardous Polymerization: None Known
Incompatible Materials
Avoid alcohols, strong bases or amines and metal compounds (such as small particle metal catalysts).
11. Toxicological Information
Ingredient(s) - Carginogenicity
METHYLENE BISPHENYL ISOCYANATE
Listed In The IARC Monographs
MATERIAL SAFETY DATA SHEET Page 4 of 5
Sika Boom
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with applicable federal, state and local government regulations.
14. Transport Information
Proper Shipping Name
Containers less than 1000 cu. cm (1 liter)
Ground: Consumer Commodity ORM-D
Air: Aerosols, Non-Flammable 2.2 UN 1950 (Non-Flammable Gas Label)
Water (export): Aerosols, Non-Flammable 2.2 UN 1950 (with a capacity of 1000 cu. cm or less)( No Hazard
Labels Required). Boxes or Cartons should be marked (Aerosols UN 1950) only. IMDG page #2102
Note: Emergency Response Guide Numbers - Consumer Commodity #171, for Aerosols
Packaging Exceptions
N/A
15. Regulatory Information
SARA Hazard Classes
Acute Health Hazard
SARA Section 313 Notification
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372. This information must be
included in all MSDSs that are copied and distributed for this material.
Ingredient(s) - U.S. Regulatory Information
FLUOROCARBON (NON-FLAMMABLE COMPRESSED GAS, HCFC)
SARA Title III - Section 313 Form "R"/TRI Reportable Chemical
METHYLENE BISPHENYL ISOCYANATE
SARA Title III - Section 313 Form "R"/TRI Reportable Chemical
SARA - Acute Health Hazard
SARA - Chronic Health Hazard
State Regulations
Based upon information currently available, this product is not known to contain detectable amounts of any
chemicals currently listed under California Proposition 65.
Ingredient(s) - State Regulations
METHYLENE BISPHENYL ISOCYANATE
New Jersey - Workplace Hazard
New Jersey - Environmental Hazard
Pennsylvania - Workplace Hazard
Massachusetts - Hazardous Substance
New York City - Hazardous Substance
16. Other Information
HMIS Rating
Health: 1
F ir e : 1
Reactivity: 1
Personal Protection: C
MATERIAL SAFETY DATA SHEET Page 5 of 5
Sika Boom
16. Other Information - Continued
Revision/Preparer Information
MSDS Preparer: EHS Department
Disclaimer
The data in this Material Safety Data Sheet relates only to the specific material herein and does not relate to use in
combination with any other materialor in any process. The information set forth herein is based on technical da ta
that Sika believes to be reliable as of the date hereof. Since conditions of use are outside our control, we make no
warranties, express or implied andassume no liability in connection with any use of this information. Nothing herein
is to be taken as a license to operate under or a recommendation to infringe any patents.
SIKA CORPORATION
Printed Using MSDS Generator鈩? 2000
|