06142002 MATERIAL SAFETY DATA SHEET : 00000032 PAGE:1
HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO CANADA L6T 2J4
(905) 459-1140
PRODUCT : LEPAGE EXTERIOR WOOD FILLER
SECTION 01: PRODUCT INFORMATION
MANUFACTURER.....................HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO
CANADA ; L6T 2J4
(905) 459-1140
AFTER HOURS - CANUTEC (613) 996-6666
WHMIS CLASSIFICATION.............D2A. WHEN THIS PRODUCT IS LABELLED AS A CONSUMER PRODUCT IT IS EXEMPT FROM
WHMIS REGULATIONS. (SEE SECTION 12(f) OF THE HAZARDOUS PRODUCTS ACT).
T.D.G. CLASSIFICATION............NOT REGULATED
PRODUCT NAME.....................LEPAGE EXTERIOR WOOD FILLER
CHEMICAL FAMILY..................SYNTHETIC POLYMER
MATERIAL USE.....................WOOD FILLER
SECTION 02: HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % EXPOSURE LEVELS C.A.S. # LD/50, ROUTE, SPECIES LC/50, ROUTE, SPECIES
Crystalline silica 0.1-1 0.1 mg/m3 (dust) 14808-60-7 Not available Not available
SECTION 03: PHYSICAL DATA
PHYSICAL STATE...................Paste
APPEARANCE & ODOUR...............Tan paste. Slight odour
ODOUR THRESHOLD (ppm)............Not available
VAPOUR PRESSURE (mm Hg)..........17.5 @ 20 deg C
VAPOUR DENSITY (AIR=1)...........0.62
BY VOLUME
BY WEIGHT
EVAPORATION RATE.................1 (water)
BOILING POINT (deg C)............100 deg C
pH...............................8.5-9.5
SPECIFIC GRAVITY.................0.86
SOLUBILITY IN WATER (% W/W)......Slightly Soluble
COEFFICIENT OF WATER/OIL.........Not available
DISTRIBUTION
SECTION 04: FIRE & EXPLOSION DATA
FLAMMABILITY
IF YES, UNDER WHICH..............Not applicable
CONDITIONS?
AUTO IGNITION TEMPERATURE........Not available
EXTINGUISHING MEDIA.............."Alcohol" Foam, CO2, Dry Chemical. Water fog
SPECIAL PROCEDURES...............Fire fighters should be equipped with self-contained breathing apparatus
to protect against potentially toxic and irritating fumes.
FLASH POINT (C), METHOD..........Not applicable
LOWER FLAMMABLE LIMIT (% VOL)....Not applicable
UPPER FLAMMABLE LIMIT (% VOL)....Not applicable
HAZARDOUS COMBUSTION PRODUCTS....Oxides of carbon (CO,CO2)
SECTION 05: REACTIVITY DATA
CHEMICAL STABILITY:
YES........................Stable under normal temperature and pressure.
NO, WHICH CONDITIONS ?
COMPATIBILITY WITH OTHER
SUBSTANCES:
YES
NO, WHICH ONES?
REACTIVITY CONDITIONS ?..........Product is stable; hazardous polymerization will not occur.
HAZARDOUS PRODUCTS OF............Oxides of carbon (CO,CO2) at high temperatures.
DECOMPOSITION
SECTION 06: TOXICOLOGICAL PROPERTIES
SKIN CONTACT...............May be a sensitizer. May cause irritation, especially on prolonged contact.
SKIN ABSORPTION............Unlikely to be absorbed through skin.
EYE CONTACT................Slightly irritating but does not cause eye tissue damage.
INHALATION.................Vapours may be irritating to respiratory system and nasal passages. The
dust of this product constitutes a potential inhalation hazard. May cause
delayed lung damage.
06142002 MATERIAL SAFETY DATA SHEET : 00000032 PAGE:2
PRODUCT : LEPAGE EXTERIOR WOOD FILLER
SECTION 06: TOXICOLOGICAL PROPERTIES
INGESTION..................No hazard in normal industrial use.
EFFECTS OF ACUTE EXPOSURE........Refer to route of entry.
EFFECTS OF CHRONIC EXPOSURE......Prolonged or repeated contact may cause irritation. This product contains
crystalline silica. Prolonged exposure to respirable crystalline quartz
may cause delayed (chronic) lung injury (silicosis).
LD 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
LC 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
EXPOSURE LIMIT OF MATERIAL.......Not available
IRRITANCY OF MATERIAL............Not available
SENSITIZING CAPABILITY OF........None known
MATERIAL
CARCINOGENICITY OF MATERIAL......Crystalline silica is an IARC-listed known lung carcinogen.
MUTAGENICITY OF MATERIAL.........None known
REPRODUCTIVE EFFECTS.............None known
TERATOGENICITY OF MATERIAL.......None known
SYNERGISTIC MATERIALS............Not available
SECTION 07: PREVENTATIVE MEASURES
GLOVES/ TYPE...............Chemical resistant gloves.
RESPIRATORY/TYPE...........Use approved respirator for dusts and mists when sanding, grinding or
machining cured compound.
EYE/TYPE...................Safety glasses with side-shields
FOOTWEAR/TYPE..............Standard work shoes.
CLOTHING/TYPE..............Standard work clothes.
VENTILATION REQUIREMENTS.........Use adequate general ventilation.
LEAK/SPILL.......................Clean up spills immediately. Absorb residual material with sand, or other
absorbent material. Flush area with plenty of water. Collect waste in
sealed containers.
WASTE DISPOSAL...................In accordance with municipal, provincial and federal regulations. Since
emptied container retains product residues all labelled hazard precautions
must be observed.
HANDLING PROCEDURES AND..........Avoid chronic inhalation of dust. Use adequate ventilation. Avoid
EQUIPMENT breathing vapours. Avoid skin and eye contact. Wear chemical splash
goggles, gloves, and protective clothing. Wash thoroughly after handling.
STORAGE NEEDS....................Store in a cool, dry place away from direct heat. Maximum storage
temperature is 38 deg C
SPECIAL SHIPPING INSTRUCTIONS....Protect against physical damage.
SECTION 08: FIRST AID MEASURES
EYE CONTACT......................Immediately flush with water for a minimum of 15 minutes holding lids
apart to ensure flushing of entire surface. Washing within 1 minute is
essential to achieve maximum effectiveness. If irritation persists, get
medical attention.
INGESTION........................Dilute with large quantities of water or milk. DO NOT induce vomiting. Get
immediate medical attention. Never give anything by mouth to an
unconscious person. Get immediate medical attention
INHALATION.......................Remove to fresh air. If symptoms develop, seek medical attention.
SKIN CONTACT.....................Remove contaminated clothing. Wash affected area with water and soap. Seek
medical attention if irritation occurs or persists.
SECTION 09: PREPARATION INFORMATION
PREPARED BY:.....................Regulatory Affairs
TELEPHONE NUMBER:................(905) 459-1140
DISCLAIMER2:.....................All information, recommendations, and suggestions appearing herein
concerning our product are based upon tests and data believed to be
reliable. However, it is the user's responsibility to determine the
safety, toxicity, and suitability for his own use of the product described
herein. Since the actual use by others is beyond our control, no
guarantee, express or implied, is made by Henkel Consumer Adhesives as to
the effects of such use, the results obtained, or the safety and toxicity
of the product nor does Henkel Consumer Adhesives assume any liability
arising out of use, by others, of the product referred to herein. The
information herein is not to be construed as absolutely complete since
additional information may be necessary or desirable when particular or
exceptional conditions or circumstan ces exist or because of applicable
laws or government regulations.
PREPARATION DATE.................JUN 13/2002
CANUTEC EMERGENCY (613) 996-6666
|