06172002 MATERIAL SAFETY DATA SHEET : 00000568 PAGE:1
HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO CANADA L6T 2J4
(905) 459-1140
PRODUCT : LEPAGE LPL 9410 PREMIUM HARDWOOD FLOORING ADHESIVE
SECTION 01: PRODUCT INFORMATION
MANUFACTURER.....................HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO
CANADA ; L6T 2J4
(905) 459-1140
AFTER HOURS - CANUTEC (613) 996-6666
WHMIS CLASSIFICATION.............D1A. D1B. D2A. D2B. WHEN THIS PRODUCT IS LABELLED AS A CONSUMER PRODUCT IT
IS EXEMPT FROM WHMIS REGULATIONS. (SEE SECTION 12(f) OF THE HAZARDOUS
PRODUCTS ACT).
T.D.G. CLASSIFICATION............NOT REGULATED
PRODUCT NAME.....................LEPAGE LPL 9410 PREMIUM HARDWOOD FLOORING ADHESIVE
CHEMICAL FAMILY..................MIXTURE
MATERIAL USE.....................ADHESIVE
SECTION 02: HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % EXPOSURE LEVELS C.A.S. # LD/50, ROUTE, SPECIES LC/50, ROUTE, SPECIES
Talc (hydrous magnesium 10-30 2 mg/m3 14807-96-6 Not available Not available
silicate)
Light petroleum distillate, 7-13 100ppm 64742-47-8 >5.0g/kg,oral,rat Not available
hydrotreated
Polymethylene polyphenyl 5-10 Not available 9016-87-9 >10g/kg oral,rat 490mg/m3/4hr
isocyanate inhal., rat
Methylene bisphenyl 10-30 TLV-TWA:0.051mg/m3 101-68-8 >10g/kg,oral,rat <490mg/m3/4hr
diisocyanate TLV-TWA:0.005 ppm 2.2g/kg,oral,rabbit inhal., rat
SECTION 03: PHYSICAL DATA
PHYSICAL STATE...................Liquid
APPEARANCE & ODOUR...............Brown viscous material with mild oily odor.
ODOUR THRESHOLD (ppm)............No data available
VAPOUR PRESSURE (mm Hg)..........< 1mmHg @ 25 deg C
VAPOUR DENSITY (AIR=1)...........Heavier than air
VOLATILES %
BY VOLUME..................13-17 %
BY WEIGHT
EVAPORATION RATE.................Slower than n-butyl acetate
BOILING POINT....................> 249 deg C
FREEZING POINT...................Not available
pH...............................Not available
SPECIFIC GRAVITY.................1.25
SOLUBILITY IN WATER (% W/W)......Negligible (< 0.1 %)
COEFFICIENT OF WATER/OIL.........Not applicable
DISTRIBUTION
SECTION 04: FIRE & EXPLOSION DATA
FLAMMABILITY.....................Not flammable
IF YES, UNDER WHICH
CONDITIONS?
EXTINGUISHING MEDIA..............Water fog; Foam; CO2; Dry chemical
SPECIAL PROCEDURES...............Fire fighters should be equipped with self-contained breathing apparatus
to protect against potentially toxic and irritating fumes. Use water to
cool exposed containers. Water stream directed into fire may cause
frothing with subsequent spread of fire.
FLASH POINT (C), METHOD..........121 deg C, (TAG)
AUTO IGNITION TEMPERATURE........Not available
UPPER FLAMMABLE LIMIT (% VOL)....7.0 % (in air)
LOWER FLAMMABLE LIMIT (% VOL)....0.6 % (in air)
HAZARDOUS COMBUSTION PRODUCTS....Irritating and/or toxic gases or fumes may be generated by thermal
decomposition or combustion. Closed containers may rupture or explode (due
to pressure build-up) when exposed to extreme heat. Oxides of carbon
(CO,CO2). Oxides of nitrogen
EXPLOSION DATA
SENSITIVITY TO STATIC............Not applicable
DISCHARGE
SENSITIVITY TO IMPACT......Not applicable
RATE OF BURNING............Not applicable
EXPLOSIVE POWER............Not applicable
06172002 MATERIAL SAFETY DATA SHEET : 00000568 PAGE:2
PRODUCT : LEPAGE LPL 9410 PREMIUM HARDWOOD FLOORING ADHESIVE
SECTION 05: REACTIVITY DATA
CHEMICAL STABILITY:
YES........................Stable under normal temperature and pressure.
NO, WHICH CONDITIONS ?.....Heating may cause pressure build-up and possible rupture of the container.
COMPATIBILITY WITH OTHER
SUBSTANCES:
YES
NO, WHICH ONES?............Strong bases or oxidants. Strong Lewis or mineral acids. Water. Alcohols.
Surface-active compounds. Amines
REACTIVITY CONDITIONS ?..........Contact with moisture and other materials which react with isocyanates.
Long-term exposure to elevated temperatures. Sources of ignition.
HAZARDOUS PRODUCTS OF............Acrid fumes. Oxides of carbon (CO,CO2). Oxides of nitrogen. Traces of
DECOMPOSITION hydrogen cyanide in an oxygen-deficient environment.
SECTION 06: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY:
SKIN CONTACT...............Severe irritant. May cause dermatitis and allergic responses.
SKIN ABSORPTION............Strong skin sensitizer.
EYE CONTACT................Moderate irritant. May cause tearing, reddening of the eyes and reversible
corneal injury.
INHALATION.................Causes irritation of respiratory tract. Severe exposure can also cause
wheezing, chest pain, and delayed pulmonary edema.
INHALATION, ACUTE :..............Respiratory irritant and sensitizer. Lung irritation and chest pain.
Material aspirated into lungs may cause chemical pneumonitis.
INGESTION..................May cause irritation of mouth, throat, and stomach.
EFFECTS OF ACUTE EXPOSURE........Skin, eye, and respiratory tract irritation.
EFFECTS OF CHRONIC EXPOSURE......May aggravate existing eye, skin, and lung conditions. This product
contains isocyanate. Isocyanates have been shown to cause sensitization in
individuals overexpose d to products containing such material. Deliberate
and repeated inhalation of concentrated solvent vapors may cause permanent
neurological damage. Chronic overexposure effects are targeted at the
kidneys and liver.
LD 50 OF MATERIAL, SPECIES &.....Refer to hazardous ingredients section.
ROUTE
LC 50 OF MATERIAL, SPECIES &.....Refer to hazardous ingredients section.
ROUTE
EXPOSURE LIMIT OF MATERIAL.......See hazardous ingredients section (2)
IRRITANCY OF MATERIAL............Moderate
SENSITIZING CAPABILITY OF........Repeated contact may cause allergic skin and/or respiratory reactions
MATERIAL resulting in sensitization of the individual. Respiratory sensitivity
results in asthma-like symptoms on subsequent exposure. Individuals
previously sensitized to isocyanates should take proper precautions
against exposure by following proper handling procedures.
CARCINOGENICITY OF MATERIAL......This product may contain crystalline silica. Crystalline silica is an
IARC-listed known lung carcinogen.
REPRODUCTIVE EFFECTS.............None known
MUTAGENICITY OF MATERIAL.........None known
TERATOGENICITY OF MATERIAL.......None known
SYNERGISTIC MATERIALS............None known
SECTION 07: PREVENTATIVE MEASURES
PROTECTIVE EQUIPMENT
GLOVES/ TYPE...............Butyl rubber gloves.
RESPIRATORY/TYPE...........If the TLV is exceeded, or if used in a poorly ventilated space or area
with limited ventilation, use an approved respirator in accordance with
applicable safety regulations. Use approved respirator for dusts and mists
when sanding, grinding or machining cured compound.
EYE/TYPE...................Wear chemical safety goggles.
FOOTWEAR/TYPE..............Standard work shoes.
CLOTHING/TYPE..............Clothing that covers any exposed area of arms, legs or torso.
OTHER/TYPE.................Eye bath and safety shower.
ENGINEERING CONTROLS.............Local exhaust as needed to control vapor/dust levels to below recommended
limits.
LEAK/SPILL.......................Ventilate. Eliminate all sources of ignition. Wear adequate protective
clothing and equipment. Contain the spill. Absorb with inert material.
Scrape or shovel into containers. Cover loosely and remove to appropriate
well ventilated area until disposal. Wash spill area with soap and water.
Prevent washings from entering waterways.
WASTE DISPOSAL...................In accordance with municipal, provincial and federal regulations. Since
emptied container retains product residues all labelled hazard precautions
must be observed.
HANDLING PROCEDURES AND..........For professional use only. Do not take internally. Avoid contact with
EQUIPMENT eyes, skin, and clothing. Wear appropriate personal protective equipment.
Avoid breathing vapours. Use with adequate ventilation and employ
respiratory protection where spray or mist may be generated. Tightly
reseal all partially used containers. Avoid smoking, drinking or eating in
use. Wash thoroughly after handling.
STORAGE NEEDS....................Protect containers from physical damage to avoid leaks and spills. Keep
container closed when not in use. KEEP AWAY FROM CHILDREN.
SPECIAL SHIPPING INSTRUCTIONS....None.
06172002 MATERIAL SAFETY DATA SHEET : 00000568 PAGE:3
PRODUCT : LEPAGE LPL 9410 PREMIUM HARDWOOD FLOORING ADHESIVE
SECTION 08: FIRST AID MEASURES
SKIN CONTACT.....................Remove contaminated clothing. Wash affected area with water and soap. Seek
medical attention if irritation occurs or persists.
EYE CONTACT......................Immediately flush with water for a minimum of 15 minutes holding lids
apart to ensure flushing of entire surface. Washing within 1 minute is
essential to achieve maximum effectiveness. Obtain immediate medical
attention.
INHALATION.......................Remove victim to fresh air. If not breathing qualified personnel should
administer artificial respiration. Get medical attention.
INGESTION........................Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs. Obtain
immediate medical attention.
SECTION 09: PREPARATION INFORMATION
PREPARED BY:.....................Regulatory Affairs
TELEPHONE NUMBER:................(905) 459-1140
DISCLAIMER2:.....................All information, recommendations, and suggestions appearing herein
concerning our product are based upon tests and data believed to be
reliable. However, it is the user's responsibility to determine the
safety, toxicity, and suitability for his own use of the product described
herein. Since the actual use by others is beyond our control, no
guarantee, express or implied, is made by Henkel Consumer Adhesives as to
the effects of such use, the results obtained, or the safety and toxicity
of the product nor does Henkel Consumer Adhesives assume any liability
arising out of use, by others, of the product referred to herein. The
information herein is not to be construed as absolutely complete since
additional information may be necessary or desirable when particular or
exceptional conditions or circumstan ces exist or because of applicable
laws or government regulations.
PREPARATION DATE.................JUN 17/2002
CANUTEC EMERGENCY (613) 996-6666
|