06142002 MATERIAL SAFETY DATA SHEET : 00000013 PAGE:1
HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO CANADA L6T 2J4
(905) 459-1140
PRODUCT : LEPAGE INSTABOND SUPER GLUE
SECTION 01: PRODUCT INFORMATION
MANUFACTURER.....................HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO
CANADA ; L6T 2J4
(905) 459-1140
AFTER HOURS - CANUTEC (613) 996-6666
WHMIS CLASSIFICATION.............B3. D2B. WHEN THIS PRODUCT IS LABELLED AS A CONSUMER PRODUCT IT IS EXEMPT
FROM WHMIS REGULATIONS. (SEE SECTION 12(f) OF THE HAZARDOUS PRODUCTS ACT).
T.D.G. CLASSIFICATION............NOT REGULATED
PRODUCT NAME.....................LEPAGE INSTABOND SUPER GLUE
CHEMICAL FAMILY..................CYANOACRYLATE ADHESIVE
MATERIAL USE.....................ADHESIVE
SECTION 02: HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % EXPOSURE LEVELS C.A.S. # LD/50, ROUTE, SPECIES LC/50, ROUTE, SPECIES
2-Propenoic acid, 2-cyano- 60-100 TLV-TWA: 2 PPM 137-05-3 Not available Not available
methyl ester
SECTION 03: PHYSICAL DATA
PHYSICAL STATE...................Liquid
APPEARANCE & ODOUR...............Transparent. Pungent odour
ODOUR THRESHOLD (ppm)............Not available
VAPOUR PRESSURE (mm Hg)..........0.3 @ 24 deg C
VAPOUR DENSITY (AIR=1)...........> 1
BY VOLUME
BY WEIGHT
EVAPORATION RATE.................Not available
BOILING POINT (deg C)............48 deg C @ 2.5 mm Hg
pH...............................Not applicable
SPECIFIC GRAVITY.................1.10
SOLUBILITY IN WATER (% W/W)......Insoluble
COEFFICIENT OF WATER/OIL.........Not available
DISTRIBUTION
SECTION 04: FIRE & EXPLOSION DATA
FLAMMABILITY
IF YES, UNDER WHICH..............Not applicable
CONDITIONS?
AUTO IGNITION TEMPERATURE........Not available
EXTINGUISHING MEDIA..............CO2. Dry chemical. Foam
SPECIAL PROCEDURES...............Fire fighters should be equipped with self-contained breathing apparatus
to protect against potentially toxic and irritating fumes.
FLASH POINT (C), METHOD..........75 C, Setaflash Closed Tester
LOWER FLAMMABLE LIMIT (% VOL)....Not applicable
UPPER FLAMMABLE LIMIT (% VOL)....Not applicable
HAZARDOUS COMBUSTION PRODUCTS....Oxides of carbon (CO,CO2). Oxides of nitrogen
SECTION 05: REACTIVITY DATA
CHEMICAL STABILITY:
YES........................Under normal conditions
NO, WHICH CONDITIONS ?
COMPATIBILITY WITH OTHER
SUBSTANCES:
YES
NO, WHICH ONES?............Water. Alkaline materials. Peroxides or other polymerization initiators
REACTIVITY CONDITIONS ?..........Contamination of adhesive with alkaline materials, peroxides or water can
result in rapid polymerization. In large quantities, this could lead to an
uncontrollable rise in temperature and a buildup of pressure in closed
containers.
HAZARDOUS PRODUCTS OF............Stable under normal temperature and pressure.
DECOMPOSITION
SECTION 06: TOXICOLOGICAL PROPERTIES
SKIN CONTACT...............Immediately bonds skin. May cause irritation, especially on prolonged
contact.
06142002 MATERIAL SAFETY DATA SHEET : 00000013 PAGE:2
PRODUCT : LEPAGE INSTABOND SUPER GLUE
SECTION 06: TOXICOLOGICAL PROPERTIES
SKIN ABSORPTION............May be absorbed by the skin.
EYE CONTACT................Vapours are lachrymatory. On contact, will bond eyelids together.
Cyanoacrylates will not bond to the eye but may cause corneal scratching.
INHALATION.................Irritating to mucous membranes and eyes. Vapour exposures of 40-60 ppm in
air is very objectionable, producing lacrimation, rhinorrhea, and blurred
vision. Lower concentrations, near the TLV, caused irritation of the eyes
and nose. Vapours may be irritating to respiratory system and nasal
passages
INGESTION..................Immediately bonds the mouth. It is almost impossible to swallow
cyanoacrylate. The adhesive solidifies and adheres in the mouth.
EFFECTS OF ACUTE EXPOSURE........Refer to route of entry.
EFFECTS OF CHRONIC EXPOSURE......May aggravate existing eye, skin, and lung conditions.
LD 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
LC 50 OF MATERIAL, SPECIES &.....Not available
ROUTE
EXPOSURE LIMIT OF MATERIAL.......Not available
IRRITANCY OF MATERIAL............Refer to route of entry
SENSITIZING CAPABILITY OF........None known
MATERIAL
CARCINOGENICITY OF MATERIAL......None known
SYNERGISTIC MATERIALS............Not available
SECTION 07: PREVENTATIVE MEASURES
GLOVES/ TYPE...............Polyethylene or PVC with disposible polyethylene liners. Do not wear
rubber or cloth gloves.
RESPIRATORY/TYPE...........Avoid prolonged or repeated breathing of vapour or mists. Use a NIOSH/MSHA
approved respirator whenever mist or spray is generated.
EYE/TYPE...................Safety glasses, goggles or face shield to protect against splashing.
FOOTWEAR/TYPE..............Standard work shoes.
CLOTHING/TYPE..............Standard work clothes.
VENTILATION REQUIREMENTS.........Use adequate local exhaust ventilation.
LEAK/SPILL.......................SMALL SPILLS: Wipe up with cloth. Immediately soak cloth with water to
polymerize the adhesive. Caution! Cloth containing adhesive may undergo
autoignition if not soaked with water. LARGE SPILLS: Flood area with
water. When cured, remove film with a scraper. Wear NIOSH approved
respirator for organic vapours if needed, and protective clothing.
WASTE DISPOSAL...................In accordance with municipal, provincial and federal regulations. Since
emptied container retains product residues all labelled hazard precautions
must be observed.
HANDLING PROCEDURES AND..........Use adequate ventilation. Avoid breathing vapours. Avoid skin and eye
EQUIPMENT contact. Wear chemical splash goggles, gloves, and protective clothing.
Wash thoroughly after handling.
STORAGE NEEDS....................Avoid contact with moisture. Avoid extreme temperatures. Avoid open flames.
SPECIAL SHIPPING INSTRUCTIONS....Not regulated
SECTION 08: FIRST AID MEASURES
EYE CONTACT......................Immediately flush with water for a minimum of 15 minutes holding lids
apart to ensure flushing of entire surface. Washing within 1 minute is
essential to achieve maximum effectiveness. Cured adhesive will not bond
well to surface of eye, but corneal damage from abrasion may result. Do
not wear contact lenses when working with this material.
INGESTION........................Immediate bonding of mouth will occur. Get immediate medical attention
INHALATION.......................Remove to fresh air. If breathing is difficult, give oxygen. If breathing
has stopped, give artificial respiration. Get medical attention.
SKIN CONTACT.....................Wash affected area(s) thoroughly with soap and water. Discard footwear
that has been contaminated on the inner surface. Do not remove material
from skin. Obtain medical assistance for removal.
SECTION 09: PREPARATION INFORMATION
PREPARED BY:.....................Regulatory Affairs
TELEPHONE NUMBER:................(905) 459-1140
DISCLAIMER2:.....................All information, recommendations, and suggestions appearing herein
concerning our product are based upon tests and data believed to be
reliable. However, it is the user's responsibility to determine the
safety, toxicity, and suitability for his own use of the product described
herein. Since the actual use by others is beyond our control, no
guarantee, express or implied, is made by Henkel Consumer Adhesives as to
the effects of such use, the results obtained, or the safety and toxicity
of the product nor does Henkel Consumer Adhesives assume any liability
arising out of use, by others, of the product referred to herein. The
information herein is not to be construed as absolutely complete since
additional information may be necessary or desirable when particular or
exceptional conditions or circumstan ces exist or because of applicable
laws or government regulations.
PREPARATION DATE.................JUN 13/2002
CANUTEC EMERGENCY (613) 996-6666
|