06212002 MATERIAL SAFETY DATA SHEET : 00000560 PAGE:1
HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO CANADA L6T 2J4
(905) 459-1140
PRODUCT : LEPAGE PRO 2000 PLUS - CLEAR
SECTION 01: PRODUCT INFORMATION
MANUFACTURER.....................HENKEL CONSUMER ADHESIVES
50 WEST DRIVE
BRAMPTON, ONTARIO
CANADA ; L6T 2J4
(905) 459-1140
AFTER HOURS - CANUTEC (613) 996-6666
WHMIS CLASSIFICATION.............B4. D2A. D2B. WHEN THIS PRODUCT IS LABELLED AS A CONSUMER PRODUCT IT IS
EXEMPT FROM WHMIS REGULATIONS. (SEE SECTION 12(f) OF THE HAZARDOUS
PRODUCTS ACT).
T.D.G. CLASSIFICATION............SOLIDS CONTAINING FLAMMABLE LIQUID, N.O.S. (PETROLEUM NAPHTA). CLASS 4.1,
UN 3175, PKG GP II. WHEN THIS PRODUCT IS LABELLED AS A CONSUMER COMMODITY
IT IS EXEMPT FROM T.D.G. REGULATIONS (SEE SECTION 2.7(1) OF TRANSPORTATION
OF DANGEROUS GOODS REGULATIONS).
PRODUCT NAME.....................LEPAGE PRO 2000 PLUS - CLEAR
CHEMICAL FAMILY..................THERMOPLASTIC
MATERIAL USE.....................SEALANT
SECTION 02: HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % EXPOSURE LEVELS C.A.S. # LD/50, ROUTE, SPECIES LC/50, ROUTE, SPECIES
Solvent naptha (petroleum), 15-40 TLV: 300ppm 8hrTWA 64742-89-8 >5g/kg,oral,rat Not available
light aliphatic PEL: 500ppm 8hrTWA >3.16g/kg,skin,
rabbit
Xylene 10-30 100 ppm 1330-20-7 4300mg/kg rat,oral 5000ppm/4hr rat,
inhal.
SECTION 03: PHYSICAL DATA
PHYSICAL STATE...................Paste
APPEARANCE & ODOUR...............Colourless. High viscosity smooth mastic with moderate solvent odor.
ODOUR THRESHOLD (ppm)............No data available
VAPOUR PRESSURE (mm Hg)..........5.1 mm / 20 deg C
VAPOUR DENSITY (AIR=1)...........Heavier than air
VOLATILES %
BY VOLUME..................30-35 %
BY WEIGHT
EVAPORATION RATE.................Slower than n-butyl acetate
BOILING POINT....................Not available
FREEZING POINT...................Not available
pH...............................Not applicable
SPECIFIC GRAVITY.................0.905
SOLUBILITY IN WATER (% W/W)......Insoluble in water
COEFFICIENT OF WATER/OIL.........Not applicable
DISTRIBUTION
SECTION 04: FIRE & EXPLOSION DATA
FLAMMABILITY.....................FLAMMABLE SOLID
IF YES, UNDER WHICH..............Excessive heat, sparks and open flame
CONDITIONS?
EXTINGUISHING MEDIA..............Foam. Carbon dioxide. Dry chemical
SPECIAL PROCEDURES...............Fire fighters should be equipped with self-contained breathing apparatus
to protect against potentially toxic and irritating fumes. Water stream
directed into fire may cause frothing with subsequent spread of fire.
FLASH POINT (C), METHOD..........21 deg C, CC
AUTO IGNITION TEMPERATURE........Not available
UPPER FLAMMABLE LIMIT (% VOL)....7.0 % (in air)
LOWER FLAMMABLE LIMIT (% VOL)....1.0 % (in air)
HAZARDOUS COMBUSTION PRODUCTS....Irritating and/or toxic gases or fumes may be generated by thermal
decomposition or combustion. Closed containers may rupture or explode (due
to pressure build-up) when exposed to extreme heat. Strong oxidizers.
Empty containers may contain explosive vapors or dangerous residues.
EXPLOSION DATA
SENSITIVITY TO STATIC............Not applicable
DISCHARGE
SENSITIVITY TO IMPACT......Not applicable
RATE OF BURNING............Not applicable
EXPLOSIVE POWER............Not applicable
06212002 MATERIAL SAFETY DATA SHEET : 00000560 PAGE:2
PRODUCT : LEPAGE PRO 2000 PLUS - CLEAR
SECTION 05: REACTIVITY DATA
CHEMICAL STABILITY:
YES........................Stable under normal temperature and pressure.
NO, WHICH CONDITIONS ?
COMPATIBILITY WITH OTHER
SUBSTANCES:
YES
NO, WHICH ONES?............Strong bases or oxidants. Strong Lewis or mineral acids
REACTIVITY CONDITIONS ?..........Sources of ignition.
HAZARDOUS PRODUCTS OF............Acrid fumes. Oxides of carbon (CO,CO2)
DECOMPOSITION
SECTION 06: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY:
SKIN CONTACT...............Moderate irritant. May cause dermatitis and allergic responses.
SKIN ABSORPTION............Repeated or prolonged overexposure may cause sensitization.
EYE CONTACT................Moderate irritant. May cause reversible corneal injury.
INHALATION, ACUTE :..............Irritating to respiratory tract. Intoxicant. Overexposure shown by
headache, dizziness and confusion to coma. Material aspirated into lungs
may cause chemical pneumonitis.
INGESTION..................May cause irritation/burns of mouth, throat and stomach. Symptoms include
nausea, abdominal pain and possible collapse.
EFFECTS OF ACUTE EXPOSURE........Possible skin, eye, and respiratory tract irritation.
EFFECTS OF CHRONIC EXPOSURE......This product contains xylenes. High exposure to xylenes in some animal
studies have been reported to cause health effects on the developing
embryo/fetus. The significance of these findings to humans has not been
determined. Deliberate and repeated inhalation of concentrated solvent
vapors may cause permanent neurological damage. Preexisting pulmonary and
dermatological disorders may be aggravated by exposure to hazardous
components.
LD 50 OF MATERIAL, SPECIES &.....Refer to hazardous ingredients section.
ROUTE
LC 50 OF MATERIAL, SPECIES &.....Refer to hazardous ingredients section.
ROUTE
EXPOSURE LIMIT OF MATERIAL.......Not established
IRRITANCY OF MATERIAL............Moderate
SENSITIZING CAPABILITY OF........Repeated contact may cause allergic skin and/or respiratory reactions
MATERIAL resulting in sensitization of the individual. Respiratory sensitivity
results in asthma-like symptoms on subsequent exposure.
MUTAGENICITY OF MATERIAL.........None known
TERATOGENICITY OF MATERIAL.......Xylenes have produced fetotoxic effects in animals, in the absence of
maternal toxicity. The significance of these effects to humans has not
been determined.
CARCINOGENICITY OF MATERIAL......None known
REPRODUCTIVE EFFECTS.............Xylenes represent an embryotoxic hazard in animals. Effects of exposure to
xylenes on humans have not been confirmed.
SYNERGISTIC MATERIALS............None known
SECTION 07: PREVENTATIVE MEASURES
PROTECTIVE EQUIPMENT
GLOVES/ TYPE...............Wear impervious gloves (in neoprene or rubber).
RESPIRATORY/TYPE...........If the TLV is exceeded, or if used in a poorly ventilated space or area
with limited ventilation, use an approved respirator in accordance with
applicable safety regulations. Use approved respirator for dusts and mists
when sanding, grinding or machining cured compound.
EYE/TYPE...................Wear chemical safety goggles.
FOOTWEAR/TYPE..............Work shoes
CLOTHING/TYPE..............Wear adequate protective clothes.
OTHER/TYPE.................Eye bath and safety shower.
ENGINEERING CONTROLS.............Local exhaust as needed to control vapor/dust levels to below recommended
limits.
LEAK/SPILL.......................Ventilate area. Eliminate all sources of ignition. Wear appropriate
protective equipment during cleanup. Shut off source of leak if safe to do
so. Scrape or shovel into containers. Cover loosely and remove to
appropriate well ventilated area until disposal. Wash spill area with soap
and water. Prevent washings from entering waterways. For small spills:
wipe up. Wait until solidification. Discard.
WASTE DISPOSAL...................In accordance with municipal, provincial and federal regulations. Since
emptied container retains product residues all labelled hazard precautions
must be observed.
HANDLING PROCEDURES AND..........Do not take internally. Avoid contact with eyes, skin, and clothing. Wear
EQUIPMENT appropriate personal protective equipment. Avoid breathing
vapor/dust/mist. Wash thoroughly after handling. Tightly reseal all
partially used containers. Avoid smoking, drinking or eating in use. Use
adequate ventilation.
STORAGE NEEDS....................Store away from all sources of heat and ignition. Store empty containers
away from heat and flame. KEEP AWAY FROM CHILDREN.
SPECIAL SHIPPING INSTRUCTIONS....Ship in accordance with applicable Transportation of Dangerous Goods (TDG)
regulations.
06212002 MATERIAL SAFETY DATA SHEET : 00000560 PAGE:3
PRODUCT : LEPAGE PRO 2000 PLUS - CLEAR
SECTION 08: FIRST AID MEASURES
SKIN CONTACT.....................Remove contaminated clothing. Wash affected area with water and soap. Seek
medical attention if irritation occurs or persists.
EYE CONTACT......................Immediately flush with water for a minimum of 15 minutes holding lids
apart to ensure flushing of entire surface. Washing within 1 minute is
essential to achieve maximum effectiveness. Obtain immediate medical
attention.
INHALATION.......................Remove victim to fresh air. If not breathing qualified personnel should
administer artificial respiration. Get medical attention.
INGESTION........................Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs. Obtain
immediate medical attention.
SECTION 09: PREPARATION INFORMATION
PREPARED BY:.....................Regulatory Affairs
TELEPHONE NUMBER:................(905) 459-1140
DISCLAIMER2:.....................All information, recommendations, and suggestions appearing herein
concerning our product are based upon tests and data believed to be
reliable. However, it is the user's responsibility to determine the
safety, toxicity, and suitability for his own use of the product described
herein. Since the actual use by others is beyond our control, no
guarantee, express or implied, is made by Henkel Consumer Adhesives as to
the effects of such use, the results obtained, or the safety and toxicity
of the product nor does Henkel Consumer Adhesives assume any liability
arising out of use, by others, of the product referred to herein. The
information herein is not to be construed as absolutely complete since
additional information may be necessary or desirable when particular or
exceptional conditions or circumstan ces exist or because of applicable
laws or government regulations.
PREPARATION DATE.................JUN 20/2002
CANUTEC EMERGENCY (613) 996-6666
|