MSDS-281
September 2006
MATERIAL SAFETY DATA SHEET
CIPADOME P PART A
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CIPADOME P Part A
Application and Use: Trowel applied epoxy floor surfacing for industrial floors.
Product Description: Three component trowel applied epoxy floor surfacing.
Regulatory Classification:
WHMIS Information: Class D, Division 2, Subdivision B
Transportation of Dangerous Goods Information: Not Regulated.
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
Ingredients CAS# %(pbwt) LD/50 Route/Species
Diglycidyl Ether of Bisphenol A 25068-38-6 30-60 30g/kg(Oral-Rat )
Dibutyl Phthalate 000084742 1-5 8000mg/kg(Oral-Rat) 25000mg/kg(Dermal-Rabbit)
Aromatic Hydrocarbon 64742-94-5 1-5 LD50-Not available
Glycidyl Ether of 2-ethylhexanol 2461-15-6 1-5 7800mg/kg (Oral-Rat)
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.50
Vapour Pressure: n/a Solubility in Water: Insoluble
Boiling Point: n/a Freezing/Melting Point: n/a
Viscosity:9000 cps @ 23掳C (73掳F) Vapour Density: n/a
Evaporation Rate: n/a % Volatile: (voc): 10gm/l
Odour: n/a Appearance: Medium Grey mobile liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION, ACUTE: Not considered a problem unless heated to high temperatures.
INHALATION, CHRONIC: Refer to acute inhalation.
EYE CONTACT: Irritating.
SKIN CONTACT: This product may cause skin irritation and/or sensitization after repeated contact.
/...2
MSDS-281
September 2006
INGESTION, ACUTE: Low toxicity, causes irritation.
INGESTION, CHRONIC: Low toxicity, causes irritation.
SECTION 5 - FIRST AID MEASURES
INHALATION: If inhaled, remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has
stopped, give artificial respiration. Keep person warm, quiet, and get medical attention.
EYE CONTACT: Flush with water for at least 15 minutes while forcibly holding eyelids apart to ensure complete
irrigation of all eye and lid tissue. Consult a physician if irritation develops.
SKIN CONTACT: Wash with soap and water. Launder contaminated clothing before reuse. Contact a physician.
INGESTION: If swallowed DO NOT induce vomiting. Get prompt medical attention.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: The selection of personal protective equipment varies depending upon conditions of use.
When handling product wear long sleeves, chemical resistant gloves and safety glasses with side shields. Where splashing
during mixing may occur wear full face shield. Where concentrations in air may exceed the occupational exposure limits
and where engineering work practices or other means of exposure reduction are not adequate, approved respirators may be
necessary to prevent overexposure by inhalation.
ENGINEERING CONTROLS: General ventilation; local exhaust ventilation as necessary to control any air
contaminants, to within their TLV鈥檚, in the use of this product.
HANDLING, STORAGE AND SHIPPING: Avoid all skin contact. Avoid breathing vapours of heated materials. Keep
away from heat, sparks and open flame. Wash thoroughly after handling.
SPILL CONTROL AND DISPOSAL: Consult an expert on the disposal of recovered material. Ensure disposal in
compliance with government requirements and ensure conformity to local disposal regulations. Notify the appropriate
authorities immediately. Take all additional action necessary to prevent and remedy the adverse effects of the spill.
LAND SPILL: Eliminate source of ignition. Keep public away. Prevent additional discharge of material, if possible to do
so without hazard. Prevent spills from entering sewers, watercourses or low areas. Contain spilled liquid with sand or
earth. Do not use combustible materials such as sawdust. Recover by using a suitable absorbent.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and
environmental agencies, sinking and/or suitable dispersants may be used in unconfined water.
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: >100掳C (T.C.C)
Auto ignition Temperature: Not Available
Flammable Limits: Not Available
GENERAL HAZARDS: Combustible liquid; may release vapours that combustible mixtures at or above the flash point.
Toxic gases will from upon combustion.
/...3
MSDS-281
September 2006
FIRE FIGHTING: Use water spray to cool fire exposed surfaces and to protect personnel. Use foam or dry chemical to
extinguish fire. Respiratory and eye protection required for fire fighting personnel. A self-contained breathing apparatus
(SCUBA) should be used for all indoor fires and any significant outdoor fires. For small outdoor fires, which may easily
be extinguished with a portable fire extinguisher, use of an SCUBA may not be required.
HAZARDOUS COMBUSTION PRODUCTS: Fumes, smoke, and carbon monoxide, carbon dioxide and various hydro
carbons.
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Excessive heating. Avoid contact with strong
acids bases and oxidizers.
HAZARDOUS DECOMPOSITION: Carbon dioxide, carbon monoxide, various hydrocarbons.
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|