MSDS-250

                                                    September 2006



                                      MATERIAL SAFETY DATA SHEET

                                   CPD FASTCRETE ULTRA PART A POWDER



SECTION 1 - PRODUCT INFORMATION

Manufacturer: CPD Construction Products

              219 Connie Crescent # 13

              Concord, Ontario L4K 1L4



Product Identifier: CPD Fastcrete Ultra Part A Powder



Application and Use: Used for patching of vertical, overhead and horizontal concrete.



Product Description: Patching Compound. This is a two component product. The other component is CPD Fastcrete

Ultra Part “B� Latex.



Regulatory Classification

WHMIS - Class E (Portland Cement)         Class D Division 2 Subdivision A (Silica Quartz)



Transportation of Dangerous Goods Information: Not regulated



EMERGENCY TELEPHONE NUMBERS

CANUTEC: (613) 996-6666



SECTION 2 - HAZARDOUS INGREDIENTS

The following component data is defined in accordance with sub-paragraph 13(a)(i) to (iv) or paragraph 14 (a) of the

Hazardous Products Act.



NAME                                             (pbw)%                  CAS

Sand **(Quartz)                                  30-60                   14808-60-7

Portland Cement (Hydraulic Cement)               30-60                   65997-15-1



NOTE: LD50 (not available for the above)         LC50 (not available for the above)



** The sand used in this product contains approximately 85% (by weight) Quartz. The Quartz that exists as dust particles

with an aerodynamic diameter less than 5 microns is hazardous. An approved dust mask (for crystalline Silica) should be

worn by workers handling this product in the dry state.



SECTION 3 - PHYSICAL DATA

Physical State: Powder/Granular Solid                    Specific Gravity: 2.00

Vapour Pressure: n/a                                     Solubility in Water: < 1.0%

PH: 12.0 @ 20°C (Aqueous Solution)                       Boiling Point: n/a

Viscosity: n/a                                           Vapour Density (Air=1): n/a

Evaporation Rate: n/a                                    % Volatile: n/a

Odour: None                                              Appearance: Light Grey Powder Containing Fine Sand.



SECTION 4 - TOXICOLOGICAL PROPERTIES

NATURE OF HAZARD

INHALATION: Crystalline Silica (Quartz) dust particles below 5 Microns in diameter may be present in this product.

Excessive inhalation of particles of this size (or smaller) may cause lung disease (Silicosis). The prolonged inhalation of

dust may result in irritation of nasal tissue and the cornea (white) of the eye. Certain people may develop allergic

dermatitis.



                                                                                                                       /...2

                                                      MSDS-250

                                                    September 2006



EYE CONTACT: May Irritate. No permanent damage likely.



SKIN CONTACT: Will dry skin and cause defatting dermatitis with excessive exposure of skin to dry and wet product.



INGESTION: Can cause irritation to throat.



CHRONIC: Excessive exposure inhalation could lead to development of the irreversible lung disease "Silicosis".

Crystalline silica is classified by IARC as " 2A-Probably Carcinogenic to humans".



OCCUPATIONAL EXPOSURE LIMIT: Maximum TWA of silica is 0.2 mg. per M3 of air. For further information of

the designated substance "Silica" contact the Ministry of Labour (Occupational Health and Safety Division) in your

region.



SECTION 5 - FIRST AID MEASURES

INHALATION: Remove to fresh air.



EYE CONTACT: Flush eye(s) with lukewarm water for 15 minutes holding eyelids open. If irritation persists see

physician.



INGESTION: Will irritate throat. Give individual water and see physician.



SKIN: Wash hands with soap and water. Apply good quality hand lotion. If irritation persists see physician.



SECTION 6 - PREVENTIVE MEASURES

PERSONAL PROTECTION: Wear safety glasses (with side shields), waterproof PVC or Neoprene gloves and an

approved dust mask when handling the product. Observe good personal hygiene. No engineering controls necessary.



HANDLING STORAGE AND SHIPPING: Product must be stored under dry conditions. May be stored off the ground

and under waterproof tarp in the field for short periods of time. DO NOT ALLOW product to get wet as it will harden.



SPILL CONTROL AND DISPOSAL: Sweep area with dust retarding floor sweeping compound. Dispose of as normal

garbage. No special precautions required.



SECTION 7 - FIRE AND EXPLOSION DATA

None. This product will not burn.



SECTION 8 - REACTIVITY DATA

Stable. Hazardous decomposition will not occur.



SECTION 9 - PREPARATION

Prepared By: R.J. Green

             Plant Manager

             CPD Construction Products

             Concord, Ontario L4K 1L4